ETSI EN 300 430-2002 Fixed Radio Systems Point-To-Point Equipment Parameters for Radio Systems for the Transmission of STM-1 Digital Signals Operating in the 18 GHz Frequency Band _1.pdf

《ETSI EN 300 430-2002 Fixed Radio Systems Point-To-Point Equipment Parameters for Radio Systems for the Transmission of STM-1 Digital Signals Operating in the 18 GHz Frequency Band _1.pdf》由会员分享，可在线阅读，更多相关《ETSI EN 300 430-2002 Fixed Radio Systems Point-To-Point Equipment Parameters for Radio Systems for the Transmission of STM-1 Digital Signals Operating in the 18 GHz Frequency Band _1.pdf（31页珍藏版）》请在麦多课文档分享上搜索。

1、ETSI EN 300 430 VI .4.1 (2002-07) European Sfandard (Telecommunicafions series) Fixed Radio Systems; Point-to-point equipment; Parameters for radio systems for the transmission of STM-1 digital signals operating in the 18 GHz frequency band with channel spacing of 55 MHz and 27,5 MHz 2 ETSI EN 300 4

2、30 VI .4.1 (2002-07) Reference REN/TM-04149-4 Keywords architecture, DRRS, PDH, point-to-point, SDH, STM, transmission ETSI 650 Route des Lucioles F-O6921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 O0 Fax: +33 4 93 65 47 16 Siret No 348 623 562 00017 - NAF 742 C Association but non lucrati

3、f enregistre la Sous-prfecture de Grasse (06) No 7803/88 Important notice Individual copies of the present document can be downloaded from: http:lwmv.etsi .arq The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference

4、in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the

5、 document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at ha p:/pa rta I. etsi I a rgltbistat uslstatus .as p If you find errors in the present document, send your comment to: Cori vriaht Notifica tion No part may be

6、reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. O European Telecommunications Standards Institute 2002. All rights reserved. DECTTM, PLUGTESTSTMand UMTSTMare Trade Marks of ETSI registered for the benefit of its

7、Members. TIPHONTM and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI 3 ETSI EN 300 430 VI .4.1 (2002-07) Contents Intellectual Pr

8、operty Rights . .5 Foreword . 5 1 2 3 3.1 3.2 4 4.1 4.1.1 4.1.2 4.2 4.3 4.4 4.4.1 4.4.2 4.5 4.6 4.7 4.8 4.9 4.9.1 4.9.2 4.9.3 4.9.4 4.9.5 5 5.1 5.2 5.2.1 5.2.2 5.3 5.3.1 5.3.2 5.3.2.1 5.3.2.2 5.3.2.3 5.3.3 5.3.4 5.3.5 5.3.6 5.3.6.1 5.3.6.2 5.3.7 5.3.7.1 5.3.7.2 5.3.8 5.4 5.4.1 5.4.2 5.4.3 5.4.4 5.5

9、Scope 6 Symbols and abbreviations .9 ieferences . .7 . 9 . 9 3eneral characteristics . 1 O . 10 Channel spacing for systems operating on the same route 10 Compatibility requirements be 10 Performance and availability requirements 10 Environmental conditions 11 s Frequency bands and channel Channel a

10、rrangements . 10 Equipment within weather protected locations (indoor locations) . Equipment for non-weather protected locations (outdoor locations) . . . . nt Network (TMN) interface Antenna radiation patterns . Antenna Inter-Port Isolation (IPI) Waveguide flanges (or other connectors) Return loss

11、. Branching/feeder/antenna characteristics Antenna cross-Polar Discrimination (XPD) System Parameters .13 Transmission capacity . . 13 Baseband parameters. . 13 . 13 . 13 Transmitter characteristics. . 13 . 14 . 14 Automatic Transmit Power Control (ATPC) 14 .14 .14 .15 .15 Plesiochronous interfaces

12、. . SDH baseband interface . Transmitter power range Transmit power and frequency contro Remote Transmit Power Control (RTPC) Remote Frequency Control (RFC) . Transmitter output power tolerance . Transmit Local Oscillator (LO) frequency arrangements RF spectrum mask . .15 Discrete CW lines g the spe

13、ctrum mask limit .18 Spectral lines at the symbol rate . .18 . .18 Spurious emissions . .19 .19 Spurious emissions-external . .20 Spurious emissions-internal . Radio frequency tolerance . .20 Receiver characteristics. . 20 Input level range . 20 Receiver image rejection . . 20 Spurious emissions-ext

14、ernal . 21 Spurious emissions-internal . . 21 System performance without diversity . . 21 ETSI 4 ETSI EN 300 430 VI . 4.1 (2002-07) 5.5.1 5.5.2 5.5.3 5.5.3.1 5.5.3.2 5.5.3.3 5.5.4 5.6 BER as a function of Receiver input Signal Level (RSL) . 21 Equipment Residual BER . 22 Interference sensitivity 22

15、Co-channel interference sensitivity . 22 Adjacent channel interference . 22 CW spurious interference 23 Distortion sensitivity . 23 System characteristics with diversity . 23 . . . . Annex A (informative): Additional information 24 A . 1 Radio frequency channel arrangement . 24 A.2 Feededantenna ret

16、urn loss 24 A.3 Automatic Transmit Power Control (ATPC) . 25 A.4 Spectrum masks 25 A.5 RBER . 26 A.6 Co-channel and adjacent channel interference . 27 Annex B (normative): System type codes for regulatory procedures 29 Annex C (informative): Bibliography . 30 History 31 ETSI 5 ETSI EN 300 430 VI .4.

17、1 (2002-07) Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR O00 314: “Intellect

18、ual Property Rights (7PRs); Essential, orpotentially Essential, IPRs notlJied to ETSI in respect ofETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (5). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has be

19、en carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR O00 3 14 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (Telecommunications series) has been

20、produced by ETSI Technical Committee Transmission and Multiplexing (TM). The present document contains the minimum technical requirements to ensure compatibility of products and conformance with radio regulations across ETSI member states. Radio terminals from different manufacturers are not require

21、d to interwork at radio frequency (i.e. no common air interface). However, terminals may be combined with other manufacturers equipment on a Radio Frequency (RF) branching network for operation on different polarizations. The present document defines the requirements of radio terminal and radio rela

22、y equipment and associated interfaces. The requirements for multiplex, network management and antenna/feeder equipment may be addressed elsewhere. This new version modifies only class 5b spectrum mask giving more allowance for practical implementations, without modif$ng any other requirements, and p

23、roposed design objectives for class 5a BER versus RSL. National transposition dates Date of adoption of this EN: Date of latest announcement of this EN (doa): Date of latest publication of new National Standard or endorsement of this EN (dop/e): Date of withdrawal of any conflicting National Standar

24、d (dow): 12 July 2002 3 1 October 2002 30 April 2003 30 April 2003 ETSI 6 ETSI EN 300 430 VI .4.1 (2002-07) 1 Scope The present document specifies parameters for high capacity STM- 1 digital radio-relay systems designed to operate in the 17,7 GHz to 19,7 GHz band. The channel spacing between adjacen

25、t Co-polar channels shall be 55 MHz or 27,5 MHz. Operation in the Adjacent Channel Co-Polarization (ACCP) mode for class 4 systems and class 5 systems as defiied below with orthogonal polarizations or in the alternated cross-polar mode is foreseen. Additionally for class 4 systems, operation in the

26、Co-Channel Dual Polarized (CCDP) mode with orthogonal polarization is also foreseen. The present document covers both single and multi-channel systems. The present document specifies the minimum performance parameters for terrestrial fixed service radio communications equipment operating in the freq

27、uency range 17,7 GHz to 19,7 GHz and contains a revision from the previous version, in the area of - categorization of previously considered equipments into a new spectrum efficiency class 4; - introduction of unique system type codes for regulatory reference to the various system types detailed in

28、the present document, refer to new annex C and related categories of equipment classes of spectral efficiency; new spectrum efficiency class 5 for STM-1 capacity for 27,5 MHz Adjacent Channel Alternate-Polarization (ACAP as class 5a) and Adjacent Channel Co-Polarization (ACCP as class 5b), see examp

29、les of the spectrum usageinfigures 1.laandl.lb: - I II I II Figure 1 - technical specifications relevant to the EMC Directive 30, detailed in annex B. The applications of these digital radio-relay systems are anticipated to be in the regional and access networks, at data rates of Synchronous Transpo

30、rt Module, level 1 (STM-1). The parameters to be specified fall into two categories: a) those that are required to provide compatibility between channels from different sources of equipment on the same route connected either to: - separate antennas; or - - separate polarizations of the same antenna;

31、 or one polarization of one antenna at a frequency separation of 110 MHz or more, enabling, in addition for class 4 equipment only, intenvorking of different manufacturers equipment at the same Radio Frequency (RF) branching; this category also includes parameters providing compatibility with the ex

32、isting radio-relay network. - b) parameters defining the transmission quality of the proposed system. The standardization deals with RF and baseband characteristics. Antenna/feeder system requirements are covered in EN 300 833 33. Two possible baseband interfaces for SDH systems have to be considere

33、d: one for STM-1 and another for 140 Mbit/s signals. The present document does not contain aspects related to test procedures and test conditions, however they are to be found in EN 301 126-1 19. ETSI 7 ETSI EN 300 430 VI .4.1 (2002-07) As the maximum transmission rate in a given bandwidth depends o

34、n systems spectral efficiency, different classes are defined: - class 4: equipment spectral efficiency based on typically 16 or 32-states modulation scheme (e.g. 16-QAM, 32-QAM, or equivalent); class 5: equipment spectral efficiency based on typically 64 or 128-states modulation scheme (e.g. 64-QAM,

35、 128-QAM, or equivalent). - The above classes are indicative only and do not imply any constraint to the actual modulation format, provided that all the requirements in the present document are met. Safety aspects will not be considered in the present document. However compliance to EN 60950-1 28 wi

36、ll be required to comply with Directive 1999/5/EC 29 (R Environmental conditions and environmental tests for telecommunications equipment; Part 1 : Classification of environmental conditions“. ETSI ETS 300 019-2 (all parts): “Equipment Engineering (EE); Environmental conditions and environmental tes

37、ts for telecommunications equipment; Part 2: Specification of environmental tests“. ETSI ETS 300 132-1: “Equipment Engineering (EE); Power supply interface at the input to telecommunications equipment; Part 1 : Operated by alternating current (ac) derived from direct current (dc) sources“. ETSI 8 ET

38、SI EN 300 430 VI .4.1 (2002-07) ETSI EN 300 132-2: “Environmental Engineering (EE); Power supply interface at the input to telecommunications equipment; Part 2: Operated by direct current (dc)“. ITU-T Recommendation G.703 : “Physical/electrical characteristics of hierarchical digital interfaces“. IT

39、U-T Recommendation G.773 : “Protocol suites for Q-interfaces for management of transmission systems“. ITU-T Recommendation G.784: “Synchronous digital hierarchy (SDH) management“. ITU-T Recommendation G. 82 1 : “Error performance of an international digital connection operating at a bit rate below t

40、he primary rate and forming part of an integrated services digital network“. ITU-T Recommendation G. 826: “Error performance parameters and objectives for international, constant bit rate digital paths at or above the primary rate“. ITU-T Recommendation G.957: “Optical interfaces for equipments and

41、systems relating to the synchronous digital hierarchy“. ETSI EN 300 385: “Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for fixed radio links and ancillary equipment“. ETSI EN 301 126-1: “Fixed Radio Systems; Conformance testing; Part 1:

42、 Point-to-point equipment - Definitions, general requirements and test procedures“. ETSI TR 101 036-1: “Fixed Radio Systems; Point-to-point equipment; Generic wordings for standards on digital radio systems characteristics; Part 1 : General aspects and point-to-point equipment parameters“. ETSI ETS

43、300 635: “Transmission and Multiplexing (TM); Synchronous Digital Hierarchy (SDH); Radio specific functional blocks for transmission of M x STM-N“. ETSI EN 300 645: “Telecommunications Management Network (TMN); Synchronous Digital Hierarchy (SDH) radio relay equipment; Information model for use on Q

44、 interfaces“. CEPT/ERC/REC 74-0 1 : “Spurious emissions“. ITU-T Recommendation O. 15 1 (1 992): “Error performance measuring equipment operating at the primary rate and above“. ITU-T Recommendation O. 18 1 (2000): “Equipment to assess error performance on STM-N interfaces“. ETSI TR 101 035: “Transmi

45、ssion and Multiplexing (TM); Synchronous Digital Hierarchy (SDH) aspects regarding Digital Radio Relay Systems (DRRS)“. IEC 60 154-2: “Flanges for waveguides; Part 2: Relevant specifications for flanges for ordinary rectangular waveguides“. EN 60950-1 : “Information technology equipment - Safety - P

46、art 1 : General requirements“. Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity. Council Directive 89/336/EEC of 3 May 1989 on the approximation of the laws of

47、 the Member States relating to electromagnetic compatibility. ETSI ETS 300 785: “Transmission and Multiplexing (TM); Synchronous Digital Hierarchy (SDH); Radio specific functional blocks for transmission of M x sub-STM-1“. CEPT Recommendation T/R 13-02: “Preferred channel arrangements for fixed serv

48、ices in the range 22,O GHz-29,5 GHz“. ETSI 9 ETSI EN 300 430 VI .4.1 (2002-07) i331 ETSI EN 300 833 : “Fixed Radio Systems; Point-to-point Antennas; Antennas for point-to-point fixed radio systems operating in the frequency band 3 GHz to 60 GHz“. ETSI EN 301 489-1 : “Electromagnetic compatibility an

49、d Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1 : Common technical requirements“. ETSI EN 301 489-4: “Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 4: Specific conditions for fixed radio links and ancillary equipment and services“. i341 i351 3 3.1 Symbols and abbreviations Symbols For the purposes of the present document, the following symbols apply: dB deciBel dBm GHz GigaHertz kHZ kiloHertz Mbit/s Megab