EN ISO 20869-2010 en Footwear - Test methods for outsoles insoles lining and insocks - Water soluble content《鞋靴 外底 内底 衬里和内袜的试验方法 水溶量［代替 CEN EN 12748］》.pdf

《EN ISO 20869-2010 en Footwear - Test methods for outsoles insoles lining and insocks - Water soluble content《鞋靴 外底 内底 衬里和内袜的试验方法 水溶量［代替 CEN EN 12748］》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 20869-2010 en Footwear - Test methods for outsoles insoles lining and insocks - Water soluble content《鞋靴 外底 内底 衬里和内袜的试验方法 水溶量［代替 CEN EN 12748］》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO20869:2010ICS 61.060NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDFootwear Testmethods for outsoles,insoles, lining andinsocks Watersoluble content (ISO20869:2010)This British Standardwas published under theauthority of the StandardsPolicy and Strateg

2、yCommittee on 30 June2010 BSI 2010ISBN 978 0 580 62923 5Amendments/corrigenda issued since publicationDate CommentsBS EN ISO 20869:2010National forewordThis British Standard is the UK implementation of EN ISO 20869:2010.It supersedes BS EN 12748:1999 which is withdrawn.The UK participation in its pr

3、eparation was entrusted to TechnicalCommittee TCI/69, Footwear, leather and coated fabrics.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible fo

4、r its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 20869 May 2010 ICS 61.060 Supersedes EN 12748:1999English Version Footwear - Test methods for outsoles, insoles, lining and insocks - Wat

5、er soluble content (ISO 20869:2010) Chaussures - Mthodes dessai applicables aux premires de montage, aux doublures, aux premires de propret et aux semelles dusure - Dtermination des substances solubles dans leau (ISO 20869:2010) Schuhe - Prfverfahren fr Laufsohlen, Brandsohlen, Futter und Decksohlen

6、 - Wasserlslicher Anteil (ISO 20869:2010)This European Standard was approved by CEN on 22 April 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. U

7、p-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation

8、under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germ

9、any, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG

10、 Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 20869:2010: EBS EN ISO 20869:2010EN ISO 20869:2010 (E) 3 Foreword This document (EN ISO 20869:2010) has been prepared by

11、 Technical Committee CEN/TC 309 “Footwear“, the secretariat of which is held by AENOR, in collaboration with Technical Committee ISO/TC 216 “Footwear“. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest

12、 by November 2010, and conflicting national standards shall be withdrawn at the latest by November 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all s

13、uch patent rights. This document supersedes EN 12748:1999. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

14、Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN ISO 20869:2010ISO 20869:2010(E) ISO 2010 All rights reserved iiiForew

15、ord ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a techni

16、cal committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of e

17、lectrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to

18、the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for i

19、dentifying any or all such patent rights. ISO 20869 was prepared by the European Committee for Standardization (CEN) Technical Committee CEN/TC 309, Footwear, in collaboration with Technical Committee ISO/TC 216, Footwear, in accordance with the Agreement on technical cooperation between ISO and CEN

20、 (Vienna Agreement). This second edition cancels and replaces the first edition (ISO 20869:2001) which has been technically revised. BS EN ISO 20869:2010BS EN ISO 20869:2010INTERNATIONAL STANDARD ISO 20869:2010(E) ISO 2010 All rights reserved 1Footwear Test method for outsoles, insoles, linings and

21、insocks Water soluble content 1 Scope This International Standard specifies a method for the determination of the water soluble contents for outsoles, insoles, lining and insocks. 2 Normative references The following referenced documents are indispensable for the application of this document. For da

22、ted references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 17709, Footwear Sampling location, preparation and duration of conditioning of samples and test pieces ISO 18454, Footwear Standard atmosphere

23、s for conditioning and testing of footwear and components for footwear 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 water soluble matter quantity of all those substances that, under certain conditions, are dissolved out of the material by

24、water 3.2 water soluble inorganic substances sulfated ash of water soluble substances 3.3 water soluble organic substances difference between total water solubles and sulfated ash of water solubles 4 Apparatus The following apparatus and material shall be used: 4.1 650 ml to 750 ml flask, with a wid

25、e neck and close-fitting glass or rubber stopper. 4.2 Fluted filter, 185 mm in diameter. 4.3 500 ml measuring vessel. BS EN ISO 20869:2010ISO 20869:2010(E) 2 ISO 2010 All rights reserved4.4 50 ml delivery pipette. 4.5 Quartz, platinum or porcelain evaporating basin, with flat bottom, to hold 50 ml,

26、and suitable desiccators. 4.6 Funnel and 300 ml Erlenmeyer flask. 4.7 Appropriate shaker apparatus, capable of (50 10) rpm (0,867 0,167)s. 4.8 Thermometer. 4.9 Laboratory balance, with a sensitivity of 0,1 mg. 4.10 Analytical balance. 4.11 Suitable oven, set to (102 2) C. 4.12 Water bath. 4.13 Muffl

27、e oven, set to (690 10) C. 5 Reagents 5.1 Distilled water. 5.2 1 mol/l sulfuric acid. 6 Sampling Test specimens shall be taken in accordance with ISO 17709. The material shall be ground and extracted with dichloromethane using a soxhlet apparatus for a minimum of 30 refluxes of solvent. Condition th

28、e material for 24 h in accordance with ISO 18454. A minimum of two test pieces is necessary. 7 Test method 7.1 Shaking in water Shake mechanically at (50 10) rpm for 2 h, 10 g of conditioned ground and dichloromethane extracted material with 500 ml distilled water at (23 2) C in a wide-necked flask

29、(4.1). 7.2 Filtrate Filter the contents of the flask through a fluted filter until clear. Discard the first 50 ml of the filtrate. Determine the soluble organic and inorganic substances in a further 50 ml of the subsequent filtrate. 7.3 Total water solubles Evaporate on the water bath (4.12) until d

30、ry, exactly 50 ml of the filtrate in a previously weighed dish heated at (690 10) C, drying at (102 2) C for approximately 2 h; cool in the desiccator; and weigh quickly. Only one dish at a time shall be put into a small desiccator and at most two into a large desiccator. Repeat drying until the red

31、uction in mass amounts to less than 2 mg, but not for more than 8 h. BS EN ISO 20869:2010ISO 20869:2010(E) ISO 2010 All rights reserved 37.4 Sulfated ash of water solubles Thoroughly wet the residue obtained in accordance with 7.3 in the dish with a few drops of 1 mol/l sulfuric acid (5.2), fume ove

32、r a low flame until no sulfuric acid vapour is visible. Heat until red hot. Transfer to the muffle oven (4.13) at (690 10) C for 15 min. Cool in the desiccator and weigh as quickly as possible. Repeat the addition of acid, heating, cooling and weighing until the mass of the residue is constant. NOTE

33、 If the mass of water soluble inorganic matter is likely to be less than 2,0 %, a 100 ml or 200 ml aliquot portion should be used. 8 Expression of results 8.1 The total water solubles, mws, in per cent, is given by Equation (1) dwsc10 100rmm= (1) where rdis the mass of dry residue, in grams; mcis th

34、e original mass of the component, in grams. 8.2 Sulfated ash of water solubles, msaws, in per cent, is given by Equation (2) sisawsc10 100rmm= (2) where rsiis the mass of sulfated residue from ignition, in grams. 8.3 Water soluble organic substances are the difference between the total water soluble

35、 substances and the water soluble inorganic substances. The result is the average of the two values obtained for each test piece. All values are calculated on the basis of fat free conditional samples. 9 Test report The test report shall include, at least, the following information: a) a reference t

36、o this International Standard, i.e. ISO 20869:2010; b) results, expressed in accordance with Clause 8, rounded up or down to one decimal place; c) full identification of the sample; d) reference to this method of test; e) date of testing. BS EN ISO20869:2010BSI GroupHeadquarters 389Chiswick High Roa

37、d,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBr

38、itish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity whil

39、e usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers a

40、utomatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BS

41、I Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andin

42、ternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing mem

43、bers of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to Br

44、itish Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspe

45、rmitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course o

46、f implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: