EN ISO 20863-2004 en Footwear - Test method for stiffeners and toepuffs - Bondability《鞋靴 补强胶条和皮鞋包头的试验方法 粘合程度 ISO 20863-2004》.pdf

《EN ISO 20863-2004 en Footwear - Test method for stiffeners and toepuffs - Bondability《鞋靴 补强胶条和皮鞋包头的试验方法 粘合程度 ISO 20863-2004》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 20863-2004 en Footwear - Test method for stiffeners and toepuffs - Bondability《鞋靴 补强胶条和皮鞋包头的试验方法 粘合程度 ISO 20863-2004》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN ISO 20863:2004 Footwear Test method for stiffeners and toepuffs Bondability The European Standard EN ISO 20863:2004 has the status of a British Standard ICS 61.060 BS EN ISO 20863:2004 This British Standard was published under the authority of the Standards Policy and Strategy

2、 Committee on 20 December 2004 BSI 20 December 2004 ISBN 0 580 45127 5 National foreword This British Standard is the official English language version of EN ISO 20863:2004. It is identical with ISO 20863:2004. The UK participation in its preparation was entrusted to Technical Committee TCI/69, Foot

3、wear and leather, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Cat

4、alogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its c

5、orrect application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests

6、informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN ISO title page, pages 2 to 8, an inside back cover and a back cover. The BSI copyright notice displayed in this docum

7、ent indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM ENISO20863 December2004 ICS61.060 Englishversion FootwearTestmethodforstiffenersandtoepuffsBondability (ISO20863:2004) ChaussuresMthodesdessaipour

8、cotrefortsetrenforts Aptitudeaucollage(ISO20863:2004) SchuhePrfverfahrenfrHinterkappenundZehenkappen Klebefestigkeit(ISO20863:2004) ThisEuropeanStandardwasapprovedbyCENon23August2004. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Sta

9、ndardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheCentralSecretariatortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadeby

10、tra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheCentralSecretariathasthesamestatusast heofficial versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, Germany,Greece,Hungary,Iceland,Ireland,Italy,Latvi

11、a,Lithuania,Luxembourg,Malta,Netherlands,Norway,Poland,Portugal, Slovakia, Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2004CEN Allrightsofexploitationinan

12、yformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.ENISO20863:2004:EEN ISO 20863:2004 (E) 2 Contents Page Foreword3 1 Scope4 2 Normative references4 3 Terms and definitions .4 4 Apparatus and materials.4 5 Sampling and conditioning.5 5.1 Method 1: Heat activated materials5 5.2 Method

13、2: Solvent activated materials 5 6 Procedure.5 7 Expression of results6 7.1 Dry bondability.6 7.2 Wet bondability6 8 Test report7 Annex ZA (normative) Normative references to International publications with their corresponding European publications8 EN ISO 20863:2004 (E) 3Foreword This document (EN

14、ISO 20863:2004) has been prepared by Technical Committee CEN/TC 309 “Footwear“, the secretariat of which is held by AENOR, in collaboration with Technical Committee ISO/TC 216 “Footwear“. This European Standard shall be given the status of a national standard, either by publication of an identical t

15、ext or by endorsement, at the latest by June 2005, and conflicting national standards shall be withdrawn at the latest by June 2005. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austr

16、ia, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN ISO 20863:2004 (E) 4 1 Scope T

17、his document specifies a method for the determination of the bondability of heat activated and solvent activated stiffeners and toepuffs to upper and lining materials. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated referenc

18、es, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12222, Footwear Standard atmospheres for conditioning and testing of footwear and components for footwear. EN ISO 3696, Water for analytical laboratory use

19、 Specification and test methods (ISO 3696:1987). EN ISO 4048, Leather Determination of matter soluble in dichloromethane (ISO 4048:1977). EN ISO 7500-1, Metallic materials Verification of static uniaxial testing machines Part 1: Tension/compression testing machines Verification and calibration of th

20、e force-measuring system (ISO 7500-1:2004). 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. bondability aptitude of a material to be bonded to it self or to other material by applying pressure and/or heat and eventually adhesive. 4 Apparatus and

21、materials 4.1 General The following apparatus and materials shall be used. 4.2 Tensile testing machine with a jaw separation rate of 100 mm/min 10 mm/min, an appropriate force range (this will usually be less than 100 N), capable of measuring the force to an accuracy of better than 2 % as specified

22、by class 2 in EN ISO 7500-1, which registers the force applied in terms of the displacement. 4.3 Press knife or other means of cutting rectangular test specimens of (150 mm 10mm) x (30 mm 2 mm). 4.4 Press with the following characteristics. 4.4.1 Heated plates which can maintain a pre-established te

23、mperature with a precision of 5 C. 4.4.2 Operating pressure of 245 kPa 5 kPa (245 kPa are 2,5 kg/cm 2 ). 4.5 Reference leather, full chrome splits (thickness of 1,5 mm to 1,7 mm) with a grease content of 4 % in total fat and 1 % in fatty acid (see EN ISO 4048). 4.6 Non-woven fabric, 150 g 20 g per s

24、quare metre. EN ISO 20863:2004 (E) 5 4.7 Water distilled or deionised complying with grade 3 of EN ISO 3696. 5 Sampling and conditioning 5.1 Method 1: Heat activated materials 5.1.1 Cut sufficient strips of (150 mm 10 mm) x (30 mm 2 mm) from the sample and the corresponding strips of the same size f

25、rom the non-woven fabric and the reference leather (4.5) or the material to be used. 5.1.2 Make a “compound test piece” of leather-sample-non-woven fabric. A strip of paper is placed on one of the short sides between the leather and the sample, so that 20 mm remain unstuck and so that the ends can b

26、e held in the jaws of the tensile testing machine. NOTE The side of the material to be tested should be that in contact with the standard leather, i.e. the side that in the shoe will be in contact with the upper leather. 5.1.3 Unless the manufacture establishes the application conditions, follow the

27、 Clauses 5.1.4 and 5.1.5. 5.1.4 Place the compound test piece between both press plates heated to 70 C 5 C, and apply a pressure of 245 kPa 5 kPa for 10 s. 5.1.5 Repeat the procedure described in sections 5.1.2 and 5.1.4 with the other test pieces and both press plates heated to 90 C 5 C, 110 C 5 C,

28、 130 C 5 C and 150 C 5 C, respectively. 5.1.6 Condition the set test pieces in a conditioned environment as specified in EN 12222 for 24 h. 5.2 Method 2: Solvent activated materials 5.2.1 Cut at least two strips of (150 mm 10 mm) x (30 mm 2 mm) from the sample and two strips of the same size from th

29、e non-woven fabric and the reference leather (4.5) or the material to be used. 5.2.2 Activate the test specimen by applying acetone or other solvent (4.7) to it until it is uniformly wetted, then leave it for 2,5 min 0,5 min. 5.2.3 Make a “compound test piece” of leather-sample-non-woven fabric. A s

30、trip of paper is placed on one of the short sides between the leather and the sample, so that 20 mm remain unstuck and so that the ends can be held in the jaws of the tensile testing machine. 5.2.4 Unless the manufacturer establishes the application conditions, place the compound test piece between

31、both press plates heated to 50 C 5 C, and apply a pressure of 245 kPa 5 kPa for 10 s (245 kPa are 2,5 kg/cm 2 ). 5.2.5 Condition the set test pieces in a conditioned environment as specified in EN 12222 for 24 h. 6 Procedure 6.1 Fix the reference leather of the compound test piece in one of the jaws

32、 of the tensile testing machine and the end of the sample and the non-woven fabric in the other jaw. 6.2 Operate the tensile testing machine so that the jaw separates at a speed of 100 mm/min 10 mm/min. 6.3 Stop the tensile testing machine when half the length of the test piece has been unbonded. 6.

33、4 Repeat the procedure described in 6.1, 6.2 and 6.3 with the other test pieces. EN ISO 20863:2004 (E) 6 6.5 Submerge the part of the test pieces which are still bonded, in distilled water for 16 h. 6.6 Remove a test piece from the water, hold the free ends of the wet test piece in the jaws of the t

34、ensile testing machine and unbond the rest of the test piece. 6.7 Repeat the procedure described in 6.6 with the other test pieces. 7 Expression of results 7.1 Dry bondability 7.1.1 Calculate the average value of force (see Figure 1) obtained for 6.3 and 6.4 for each one of the test pieces, in newto

35、ns. 7.1.2 Divide the average value of force obtained for each one of the test pieces by the width of the test piece, measured in millimetres, and express the dry bondability, in newtons per millimetre. Key 1 Force, in N 2 Average 3 Deformation Figure 1 Example of diagram force/deformation 7.2 Wet bo

36、ndability 7.2.1 Calculate the average value of force obtained for 6.6 and 6.7 for each one of the wet test pieces, in newtons. 7.2.2 Divide the average value of force obtained in each one of the test pieces by the width of the test pieces, measured in millimetres, and express the wet bondability in

37、newtons per millimetre. EN ISO 20863:2004 (E) 7 8 Test report The test report shall include the following information: a) reference to this document; EN ISO 20863; b) a description of the samples tested, including commercial styles, codes, colours, nature, etc.; c) the average dry bondability or the

38、 average for each temperature tested as shown in 7.1; d) the average wet bondability or the average for each temperature tested as shown in 7.2; e) date of testing; f) any deviation from this standard test method. EN ISO 20863:2004 (E) 8 Annex ZA (normative) Normative references to International pub

39、lications with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) a

40、pplies. Publication Year Title EN Year ISO 3696 1987 Water for analytical laboratory use Specification and test methods. EN ISO 3696 1995 ISO 4048 1977 Leather Determination of matter soluble in dichloromethane EN ISO 4048 1998 ISO 7500-1 2004 Metallic materials Verification of static uniaxial testi

41、ng machines Part 1: Tension/compression testing machines Verification and calibration of the force- measuring system. EN ISO 7500-1 2004 ISO 18454 2001 Footwear Standard atmospheres for conditioning and testing of footwear and components for footwear EN 12222 1997 blankBS EN ISO 20863:2004 BSI 389 C

42、hiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are upda

43、ted by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British

44、 Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically re

45、ceive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/ww

46、w.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international s

47、tandards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribi

48、ng members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI