EN ISO 12127-1-2015 en Clothing to protect against heat and flame - Determination of contact heat transmission through clothing or constituent materials - Part 1 Contact heat produ.pdf

《EN ISO 12127-1-2015 en Clothing to protect against heat and flame - Determination of contact heat transmission through clothing or constituent materials - Part 1 Contact heat produ.pdf》由会员分享，可在线阅读，更多相关《EN ISO 12127-1-2015 en Clothing to protect against heat and flame - Determination of contact heat transmission through clothing or constituent materials - Part 1 Contact heat produ.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN ISO 12127-1:2015Clothing to protectagainst heat and flame Determination of contact heattransmission through clothingor constituent materialsPart 1: Contact heat produced by heatingcylinderBS EN ISO 12127-1:2015 BRITISH STANDARDNational forewordThis British Standard is

2、the UK implementation of EN ISO12127-1:2015. It supersedes BS EN 702:1995 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PH/3/2, Heat and Flame Personal Protective Equipment.A list of organizations represented on this committee can beobtained on reques

3、t to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 73132 7ICS 13.340.10Compliance with a British Stan

4、dard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 January 2016.Amendments/corrigenda issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 12127-1

5、December 2015 ICS 13.340.10 Supersedes EN 702:1994English Version Clothing to protect against heat and flame - Determination of contact heat transmission through clothing or constituent materials - Part 1: Contact heat produced by heating cylinder (ISO 12127-1:2015) Vtements de protection contre la

6、chaleur et la flamme - Dtermination de la transmission thermique par contact travers les vtements de protection ou leurs matriaux constitutifs - Partie 1 : Transmission thermique par contact produite par un cylindre de chauffage (ISO 12127-1:2015) Schutzkleidung gegen Hitze und Flammen - Bestimmung

7、des Kontaktwrmedurchgangs durch Schutzkleidung oder -materialien - Teil 1: Durch heie Zylinder erzeugte Kontaktwrme (ISO 12127-1:2015)This European Standard was approved by CEN on 12 September 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditi

8、ons for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists i

9、n three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standar

10、ds bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slove

11、nia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved

12、worldwide for CEN national Members. Ref. No. EN ISO 12127-1:2015 EBS EN ISO 12127-1:2015EN ISO 12127-1:2015 (E) 3 European foreword This document (EN ISO 12127-1:2015) has been prepared by Technical Committee CEN/TC 162 “Protective clothing including hand and arm protection and lifejackets“, the sec

13、retariat of which is held by DIN, in collaboration with Technical Committee ISO/TC 94 “Personal safety - Protective clothing and equipment“. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 20

14、16, and conflicting national standards shall be withdrawn at the latest by June 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights.

15、This document supersedes EN 702:1994. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an

16、integral part of this document. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Re

17、public of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 12127-1:2015 has bee

18、n approved by CEN as EN ISO 12127-1:2015 without any modification. BS EN ISO 12127-1:2015EN ISO 12127-1:2015 (E) 4 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 89/686/EEC This European Standard has been prepared under a mandate giv

19、en to CEN by the European Commission and the European Free Trade Association to provide a means of conforming to Essential Requirements of the New Approach Directive 89/686/EEC on the approximation of the laws of the Member States relating to personal protective equipment. Once this standard is cite

20、d in the Official Journal of the European Union under that Directive and has been implemented as a national standard in at least one Member State, compliance with the clauses of this standard, together with the relevant requirements given in the product standards, confers within the limits of the sc

21、ope of those standards, a presumption of conformity with the Essential Requirement 3.6.1 of Annex II of that Directive and associated EFTA regulations. WARNING Other requirements and other EU Directives may be applicable to the product(s) falling within the scope of this standard. BS EN ISO 12127-1:

22、2015ISO 12127-1:2015(E)Foreword ivIntroduction v1 Scope . 12 Terms and definitions . 13 Principle 14 Apparatus . 25 Sampling and conditioning 25.1 Sampling . 25.2 Conditioning 36 Test method . 36.1 Starting conditions 36.2 Procedure 36.3 Evaluation 37 Test report . 3Annex A (informative) Best practi

23、ces for cleaning the heating cylinder 8Annex B (normative) Determination of property values for rating and classification 9 ISO 2015 All rights reserved iiiContents PageBS EN ISO 12127-1:2015ISO 12127-1:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation

24、 of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.

25、International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those

26、 intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (se

27、e www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the docum

28、ent will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and e

29、xpressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationISO 12127-1 was prepared by Technical Committee ISO/TC 94, Personal safety Protective clo

30、thing and equipment, Subcommittee SC 13, Protective clothing, and by Technical Committee CEN/TC 162, Protective clothing including hand and arm protection and lifejackets in collaboration.This second edition cancels and replaces the first edition (ISO 12127-1:2007), of which it constitutes a minor r

31、evision. The following changes have been made:a) title, for better comprehension;b) alphabetical order, “Terms and definitions”;c) modified clause for “Heating cylinder” regarding example and pictures;d) modified clause for “Calorimeter” regarding more detailed information;e) modified clause for “As

32、sembly” regarding speed and picture;f) latest standard numbers in clause “Test report”;g) new Annex A for “Best practices for cleaning the heating cylinder”;h) new Annex B for “Determination of property values for rating and classification”.ISO 12127 consists of the following parts, under the genera

33、l title Clothing for protection against heat and flame Determination of contact heat transmission through protective clothing or constituent materials : Part 1: Contact heat produced by heating cylinder Part 2: Test method using contact heat produced by dropping small cylindersiv ISO 2015 All rights

34、 reservedBS EN ISO 12127-1:2015ISO 12127-1:2015(E)IntroductionProtective clothing designed to protect against heat and flame can be exposed to direct contact with hot substances or hot surfaces.The diversity of such contact conditions makes it difficult to evaluate the hazards that can arise from hi

35、gh temperature.The test method described in this part of ISO 12127 allows this heat transfer to be assessed when a heating cylinder and the clothing material are brought into contact with each other.This part of ISO 12127 forms part of a series of standards concerned with clothing designed to protec

36、t against heat and fire. ISO 2015 All rights reserved vBS EN ISO 12127-1:2015BS EN ISO 12127-1:2015Clothing for protection against heat and flame Determination of contact heat transmission through protective clothing or constituent materials Part 1: Contact heat produced by heating cylinder1 ScopeTh

37、is part of ISO 12127 specifies a test method for the determination of contact heat transmission. It is applicable to protective clothing (including hand protectors) and its constituent materials intended to protect against high contact temperatures.Application of this part of ISO 12127 is restricted

38、 to contact temperatures between 100 C and 500 C.2 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.2.1contact forceforce acting on the test specimen and the calorimeter when they have been brought into contact with the heating cylinder2.2contact temp

39、eratureTcsurface temperature of the contact area of the heating cylinder, this temperature being kept constant2.3rate of contactrelative speed with which the heating cylinder and the calorimeter with the test specimen are brought into contact with each other2.4start of timingmoment when the upper su

40、rface of the calorimeter and the bottom edge of the heating cylinder are within 10 mm of each other2.5threshold timetttime between the start of timing and the moment when the temperature of the calorimeter is 10C above its starting value3 PrincipleThe heating cylinder is heated to and maintained at

41、the contact temperature and a test specimen is placed on the calorimeter. The heating cylinder is lowered onto the test specimen supported by the calorimeter or, alternatively, the calorimeter with the specimen is lifted up to the heating cylinder. In either case, the operation is carried out at a c

42、onstant speed. The threshold time is determined by monitoring the temperature of the calorimeter.INTERNATIONAL STANDARD ISO 12127-1:2015(E) ISO 2015 All rights reserved 1BS EN ISO 12127-1:2015ISO 12127-1:2015(E)4 Apparatus4.1 Heating cylinderThe heating cylinder shall be constructed from a suitable

43、metal which can withstand temperatures of over 500C (e.g. Silver Alloy, 925 Sterling Silver). Figures 1, 2 and 3 show an example of the stamp and heating cylinder. The contact surface shall have a diameter of (25,2 0,05) mm and shall be polished. There shall be a central boring which ends 2 mm above

44、 the lower surface of the heating cylinder. This boring is intended to hold the temperature sensor, which is necessary for regulation of the temperature of the heating cylinder, and its diameter should be chosen accordingly. The heating cylinder shall be enclosed by heat-resistant insulation, leavin

45、g free the bottom contact surface.The heating cylinder shall be capable of being heated to over 500C and be capable of maintaining the chosen testing temperature.4.2 CalorimeterThe calorimeter (as shown in Figure 4) consists of a cylindrical disc of black anodized pure aluminium of (25 0,05) mm diam

46、eter, and thickness of approximately 5.0 mm and a mass of (6,63 0,03) g, which is pushed into a mounting made from polyamide 6.6 so as to be a tight fit. The upper contact surface of the disc shall be surface ground before anodization and shall have a thermocouple attached to its lower surface by me

47、ans of adhesive tape.NOTE A PR 6462 BK/02 Thermocoax thermocouple or equivalent has been found to be suitable.1)4.3 AssemblyFigure 5 shows an example of the assembly. The heating cylinder and calorimeter are mounted with parallel faces and with their symmetrical axes in line in a supporting frame. P

48、rovision shall be made for moving at a controlled speed (5,0 0,5 mm/s) either the heating cylinder down towards the calorimeter or the calorimeter up towards the heating cylinder. An additional weight shall be dimensioned in such a way that the contact force is (49 0,5) N. Between measurement, durin

49、g cooling periods, a suitable shielding shall be put between the heating cylinder and the calorimeter in order to prevent the calorimeter from being heated by thermal radiation from the heating cylinder.4.4 Electronic devicesSuitable electronic devices shall be provided to raise the temperature of the heating cylinder to the chosen testing temperature and maintain this temperature to 2C. control the rate of contact; measure and register the calorimeter temperature to an accuracy of 0,1C; measure the threshold time.5 Samplin