EN ISO 9142-2003 en Adhesives Guide to the selection of standard laboratory ageing conditions for testing bonded joints《粘合剂 胶粘件试验用标准实验室老化条件的选择指南 代替EN 29142-1993 ISO 9142-2003》.pdf

《EN ISO 9142-2003 en Adhesives Guide to the selection of standard laboratory ageing conditions for testing bonded joints《粘合剂 胶粘件试验用标准实验室老化条件的选择指南 代替EN 29142-1993 ISO 9142-2003》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 9142-2003 en Adhesives Guide to the selection of standard laboratory ageing conditions for testing bonded joints《粘合剂 胶粘件试验用标准实验室老化条件的选择指南 代替EN 29142-1993 ISO 9142-2003》.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN ISO 9142:2003 Incorporating Corrigendum No. 1 Adhesives Guide to the selection of standard laboratory ageing conditions for testing bonded joints The European Standard EN ISO 9142:2003 has the status of a British Standard ICS 83.180 BS EN ISO 9142:2003 This British Standard wa

2、s published under the authority of the Standards Policy and Strategy Committee on 8 January 2004 BSI 6 April 2004 ISBN 0 580 43188 6 National foreword This British Standard is the official English language version of EN ISO 9142:2003. It is identical with ISO 9142:2003. It supersedes BS EN 29142:199

3、3 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee PRI/52, Adhesives, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which imple

4、ment international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication doe

5、s not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/Europea

6、n committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN ISO title page, t

7、he EN ISO foreword page, the ISO title page, pages ii to iv, pages 1 to 24, the Annex ZA page and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments 15070 Corrigendum No. 1 6 April

8、2004 Corrected EN ISO foreword page and incorporation of Annex ZAEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM ENISO9142 December2003 ICS83.180 SupersedesEN29142:1993 Englishversion AdhesivesGuidetotheselectionofstandardlaboratoryageing conditionsfortestingbondedjoints(ISO9142:2003) AdhsifsGuidepou

9、rlaslectiondeconditionsnormales dessaidevieillissementenlaboratoiredesassemblages colls(ISO9142:2003) KlebstoffeAuswahlrichtlinienfrLabor AlterungsbedingungenzurPrfungvonKlebverbindungen (ISO9142:2003) ThisEuropeanStandardwasapprovedbyCENon8December2003. CENmembersareboundtocomplywiththeCEN/CENELECI

10、nternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheManagementCentreortoanyCENmember. ThisEuropeanStandardexistsinthreeoff

11、icialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheManagementCentrehasthesamestatusasthe official versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,CzechRepublic,Denmark,Finland,France

12、,Germany,Greece, Hungary,Iceland,Ireland,Italy,Luxembourg,Malta,Netherlands,Norway,Portugal,Slovakia,Spain,Sweden,SwitzerlandandUn ited Kingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2003CEN Allright

13、sofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.ENISO9142:2003EINESO19:2402(30E) 2 CORRECTED20040303 Foreword Thisdocument(ENISO9142:2003)hasbeenpreparedbyTechnicalCommitteeISO/TC61 “Plastics“incollaborationwithTechnicalCommitteeCEN/TC193“Adhesives“,thesecretaria

14、tof whichisheldbyAENOR. ThisEuropeanStandardshallbegiventhestatusofanationalstandard,eitherbypublicationof anidenticaltextorbyendorsement,atthelatestbyJune2004,andconflictingnational standardsshallbewithdrawnatthelatestbyJune2004. ThisdocumentsupersedesEN29142:1993. AccordingtotheCEN/CENELECInternal

15、Regulations,thenationalstandardsorganizationsof thefollowingcountriesareboundtoimplementthisEuropeanStandard:Austria,Belgium,Czech Republic,Denmark,Finland,France,Germany,Greece,Hungary,Iceland,Ireland,Italy, Luxembourg,Malta,Netherlands,Norway,Portugal,Slovakia,Spain,Sweden,Switzerlandand theUnited

16、Kingdom. Endorsementnotice ThetextofISO9142:2003hasbeenapprovedbyCENasENISO9142:2003withoutany modifications. NOTENormativereferencestoInternationalStandardsarelistedinAnnexZA(normative). ENISO9142:2003 Reference number ISO 9142:2003(E) OSI 3002INTERNATIONAL STANDARD ISO 9142 Second edition 2003-12-

17、15 Adhesives Guide to the selection of standard laboratory ageing conditions for testing bonded joints Adhsifs Guide pour la slection de conditions normales dessai de vieillissement en laboratoire des assemblages colls ENISO9142:2003IS:2419 O3002(E) DPlcsid Fremia ihTs PDF file mya ctnoian emdebt de

18、dyfepcaes. In ccacnadrow eitA hebods licnesilop gnic,y tihs file mirp eb yatnde iv roweb detu slahl ton ide ebtlnu deess teh typfecaes wihce era hml era deddebicsnede ti dna onstlalde t noeh comuptfrep reromign tide ehtin.g In wodlnidaot gnihs fil,e trapise atpecc tiereht nser ehnopsiiblity fo nto i

19、fnriigngn Aebods licnesilop gnic.y ehT ISO tneClar Secrteirata caceptl on siibality in this .aera Ai ebods a tedarmfo kra Aebod SystemI snctaropro.de teDials fo teh sfotwcudorp erats sut deo crtaee tihs PDF file cna f ebi dnuon tlareneG eh Ifnler oatit evt oeh file; tP ehDc-Frtaeino marapterew stpo

20、ereimizde fro irptni.gn Evyre cera neeb sah takne tsne oeru taht teh file is siutlbae fosu re yb ISO memdob rebeis. In tlnu ehikletneve y ttah lborp aem lertait gno it is f,dnuo plsaee ifnrom ttneC ehlar Secterirata ta teh serddaig sleb nevwo. ISO 3002 All irthgs erse.devr lnUeto sswrehise specified

21、, on trap fo this lbupictaion maeb y cudorperro de tuilizi den yna form ro na ybm ynae,s lecetrinoc ro mceinahcla, incliduntohp gcoiypodna gn micrfoilm, wittuoh repmissii now nritign from ietI rehSa Ot tsserdda eh ebolw or ISOs memreb i ydobn the cnuotfo yr ttseuqer ehe.r ISO cirypothg fofice saCe t

22、sopale 65 eneG 1121-HC 02 av leT. 4 + 10 947 22 1 11 xaF0 947 22 14 + 9 74 E-mial coirypthgis.o gro We bwww.is.o groii ISO 3002 Allr ihgtsser edevrENISO9142:2003IS:2419 O3002(E) I SO 3002 All irhgts seredevr iiiContents Page Foreword iv 1 Scope 1 2 Normative references. 1 3 Materials. 2 4 Apparatus.

23、 2 5 Specimens. 2 6 Procedure. 2 7 Expression of results 3 8 Test report 4 Annex A (normative) General conditions of ageing 5 Annex B (normative) Atmospheric conditions for single-variable ageing . 6 Annex C (normative) Atmospheric conditions for multi-variable ageing. 7 Annex D (normative) Atmosphe

24、ric conditions for cyclic ageing 8 Annex E (normative) Special procedures 23 Annex F (normative) Exposure to chemical attack. 24 ENISO9142:2003IS:2419 O3002(E) iv I SO 3002 All irhgts seredevrForeword ISO (the International Organization for Standardization) is a worldwide federation of national stan

25、dards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International org

26、anizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given

27、 in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75

28、 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 9142 was prepared by Technical Committee ISO/TC 61, Plast

29、ics, Subcommittee SC 11, Products. This second edition cancels and replaces the first edition (ISO 9142:1990), of which it constitutes a minor revision. ENISO9142:2003INTENRATIONAL TSANDADR IS:2419 O3002(E)I SO 3002 All irhgts seredevr 1Adhesives Guide to the selection of standard laboratory ageing

30、conditions for testing bonded joints 1 Scope This International Standard describes laboratory ageing conditions under which adhesive joints may be exposed to various environmental influences climatic or chemical for the purpose of assessing the effects of such influences on certain properties. The a

31、geing conditions are applicable to bonded assemblies and may be used to constitute a set of tests for the evaluation of an adhesive. The results obtained using the procedures described in this International Standard are not necessarily applicable to the determination of the service life of a bonded

32、assembly because there is no direct relation between the test results and the behaviour of a bonded assembly over a period of time under service conditions. However, for certain specific applications, experience with the procedures may enable a correlation to be established. NOTE The ageing conditio

33、ns should preferably be related to the specific application of the adhesive. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the refer

34、enced document (including any amendments) applies. ISO 175:1999, Plastics Methods of test for the determination of the effects of immersion in liquid chemicals ISO 291:1997, Plastics Standard atmospheres for conditioning and testing ISO 483:1988, Plastics Small enclosures for conditioning and testin

35、g using aqueous solutions to maintain relative humidity at constant value ISO 3205:1976, Preferred test temperatures ISO 4587:2003, Adhesives Determination of tensile lap-shear strength of rigid-to-rigid bonded assemblies ISO 4588:1995, Adhesives Guidelines for the surface preparation of metals ISO

36、4892 (all parts), Plastics Methods of exposure to laboratory light sources ISO 6238:2001, Adhesives Wood-to-wood adhesive bonds Determination of shear strength by compression loading ISO 9227:1990, Corrosion tests in artificial atmospheres Salt spray tests ENISO9142:2003IS:2419 O3002(E) 2 I SO 3002

37、All irhgts seredevr3 Materials 3.1 De-ionized or distilled water, having a conductivity less than 200 S/m. 3.2 Materials for ageing tests under special environmental conditions (see appropriate annex). 4 Apparatus 4.1 Conditioning chamber, meeting the requirements of ISO 483, capable of being mainta

38、ined at a temperature of (23 2) C and a relative humidity of (50 5) %. 4.2 Dry-heat chamber, ventilated and adjustable to a temperature between 20 C and 200 C. 4.3 Humid chamber, meeting the requirements of lSO 483, adjustable to a relative humidity between 25 % and 100 %. The chamber shall be equip

39、ped with a) a device to enable the temperature to be measured to within 1 C; b) a device to enable the relative humidity to be measured to within 3 % R.H. 4.4 Cold chamber, adjustable to temperatures of ( 20 3) C and ( 40 3) C. 4.5 Controlled-pressure chamber, capable of operating at a pressure of 0

40、,6 MPa 1)and at an underpressure of 0,092 MPa. 5 Specimens 5.1 Number and type The number of test specimens, and the type used, will depend on the properties to be measured and the required ageing conditions. The test specimens shall be prepared in accordance with the requirements of the appropriate

41、 ISO standard test method. Prepare a sufficient number of specimens to provide homogeneous sets of samples for testing and to provide control samples. The following International Standards, which do not constitute an exhaustive list, are applicable: ISO 4587, ISO 4588, ISO 6238. 5.2 Conditioning Spe

42、cimens shall be conditioned in the conditioning chamber (4.1) for a minimum duration of 24 h before being subjected to ageing. The conditioning shall be carried out after the adhesive has been cured in accordance with the materials specification or the methods specified by the manufacturer of the ad

43、hesive. 6 Procedure 6.1 Tests before ageing Determine the properties required for the sample under test by the appropriate test method, using specimens conditioned in accordance with 5.2. 1) 1 MPa = 10 bar ENISO9142:2003IS:2419 O3002(E) I SO 3002 All irhgts seredevr 36.2 Ageing Expose conditioned sp

44、ecimens to the environmental conditions as defined in Annex A to Annex F, as required. 6.3 Tests after ageing Determine the properties after ageing in accordance with the procedure(s) of the appropriate standard(s). Unless there are indications to the contrary in the Annexes, condition test specimen

45、s in the conditioning chamber (4.1) for (3 1) h in the case of specimens exposed at a relative humidity higher than 50 %, for at least 24 h for all other specimens, before determining the properties. In addition to the test results, all changes visible during the ageing and testing periods, includin

46、g mode of failure, shall be noted. 6.4 Controls For control purposes, a representative group of specimens shall be kept in the conditioning chamber (4.1) for the period of time covered by the ageing conditions selected. 7 Expression of results For properties that can be measured, the results obtaine

47、d are expressed as either absolute values or a relative variation with respect to the initial value. For properties that cannot be measured, the nature of the effects observed shall be noted, e.g. rupture between the substrate and adhesive, failure of cohesion of the adhesive joint due to partial or

48、 total corrosion of the substrate beneath the adhesive, etc. NOTE It may be worth verifying that the variation in a measured property is caused only by the ageing process from the following three values: A the value of the property measured before accelerated ageing; B the value of the same property measured on the co