EN ISO 7751-2016 en Rubber and plastics hoses and hose assemblies - Ratios of proof and burst pressure to maximum working pressure《橡胶和塑料软管和软管组件试验压力和爆破压力与最大工作压力比(ISO 7751 2016)》.pdf

《EN ISO 7751-2016 en Rubber and plastics hoses and hose assemblies - Ratios of proof and burst pressure to maximum working pressure《橡胶和塑料软管和软管组件试验压力和爆破压力与最大工作压力比(ISO 7751 2016)》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 7751-2016 en Rubber and plastics hoses and hose assemblies - Ratios of proof and burst pressure to maximum working pressure《橡胶和塑料软管和软管组件试验压力和爆破压力与最大工作压力比(ISO 7751 2016)》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO 7751:2016Rubber and plastics hoses and hose assemblies Ratios of proof and burst pressure to maximum working pressure( I S O 7 7 5 1 : 2 0 1 6 )BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN ISO 7751:2016 BRITISH STANDARDNational forewordThis British

2、 Standard is the UK implementation of EN ISO 7751:2016. It supersedes BS EN ISO 7751:1997+A1:2011 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/66, Rubber and plastics tubing, hoses and hose assemblies.A list of organizations represented on this

3、committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 89088 8 ICS 2

4、3.040.70 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STAN

5、DARD NORME EUROPENNE EUROPISCHE NORM EN ISO 7751 November 2016 ICS 23.040.70 Supersedes EN ISO 7751:1997English Version Rubber and plastics hoses and hose assemblies - Ratios of proof and burst pressure to maximum working pressure (ISO 7751:2016) Tuyaux et flexibles en caoutchouc et en plastique - R

6、apports des pressions dpreuve et de rupture la pression maximale de service (ISO 7751:2016) Gummi- und Kunststoffschluche und -schlauchleitungen - Verhltnisse von Prf- und Berstdruck zum Betriebsdruck (ISO 7751:2016) This European Standard was approved by CEN on 9 October 2016. CEN members are bound

7、 to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN

8、-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre ha

9、s the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Lu

10、xembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brus

11、sels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 7751:2016 EBS EN ISO 7751:2016EN ISO 7751:2016 (E) 3 European foreword This document (EN ISO 7751:2016) has been prepared by Technical Committee ISO/TC 45 “Rubber and ru

12、bber products “ in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies” the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the

13、latest by May 2017, and conflicting national standards shall be withdrawn at the latest by May 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such

14、patent rights. This document supersedes EN ISO 7751:1997. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, F

15、inland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text o

16、f ISO 7751:2016 has been approved by CEN as EN ISO 7751:2016 without any modification. BS EN ISO 7751:2016ISO 7751:2016(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Proof pressure ratio 15 Minimum burst pressure ratio 1Bibliography 3 ISO 2016 All rights reserved iiiCo

17、ntents PageBS EN ISO 7751:2016ISO 7751:2016(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each memb

18、er body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Ele

19、ctrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types

20、of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be hel

21、d responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information

22、 given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers

23、to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Rubber and plastics hoses and hose assemblies.This third edition cancels and replaces the second edition (ISO 7751:1991), which

24、 has been technically revised. It also incorporates the Amendment ISO 7751:1991/Amd.1:2011.The main changes are as follows: the term “design working pressure” has been replaced by “maximum working pressure” throughout the text in accordance with ISO 7751:1991/Amd.1:2011; a new category (hoses for de

25、livery of cement, concrete, plaster and grout) has been added.iv ISO 2016 All rights reservedBS EN ISO 7751:2016INTERNATIONAL STANDARD ISO 7751:2016(E)Rubber and plastics hoses and hose assemblies Ratios of proof and burst pressure to maximum working pressure1 ScopeThis document specifies ratios of

26、proof pressure and minimum burst pressure to maximum working pressure for various categories of hose service.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only

27、 the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 1402, Rubber and plastics hoses and hose assemblies Hydrostatic testing3 Terms and definitionsFor the purposes of this document, the terms and definitions given in

28、 ISO 8330 apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.iso.org/obp4 Proof pressure ratioThe methods and procedures to perform

29、the proof tests are specified in ISO 1402.The ratio of proof pressure to maximum working pressure shall, unless otherwise specified, in the relevant hose/hose assembly product standard, be in accordance with Table 1, which states the pressures for guidance only. When the hose product standard specif

30、ies different pressures, these pressures shall be used when testing the hoses.5 Minimum burst pressure ratioThe methods and procedures to perform the burst tests are specified in ISO 1402.The ratio of minimum burst pressure to maximum working pressure shall, unless otherwise specified, in the releva

31、nt hose/hose assembly product standard, be in accordance with Table 1. ISO 2016 All rights reserved 1BS EN ISO 7751:2016ISO 7751:2016(E)Table 1 Ratios of proof and minimum burst pressure to maximum working pressureNo.Type of service (for guidance only)Ratio of proof pressure to maximum working pres-

32、sureRatio of minimum burst pressure to maximum working pressure1Water hose, maximum working pressure 1 MPa (10 bar)1,5 3,02Hose for all other liquids, solid materials suspended in liquids or air, and water hose, maximum working pressure more than or equal to 1 MPa (10 bar)2,0 4,03 Hose for compresse

33、d air and other gases 2,0 4,04Hose for liquid media that change into the gaseous state when subjected to a reduction in pressure, i.e. released to atmosphere2,5 5,05 Steam hose 5,0 10,06 Jetting hose 1,5 2,57Hoses for the delivery of cement, concrete, plaster and grout1,5 2,0NOTE The ratios of proof

34、 and minimum burst pressures stated in Table 1 are intended to be used for guidance only, when the hose product standard concerned does not specify these pressures for the various types and classes of hoses and hose assemblies covered by that standard.2 ISO 2016 All rights reservedBS EN ISO 7751:201

35、6ISO 7751:2016(E)BibliographyISO 8330, Rubber and plastics hoses and hose assemblies Vocabulary ISO 2016 All rights reserved 3This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publication

36、s, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their c

37、ombined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve thei

38、r goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI p

39、ublications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team

40、.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information

41、 to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever

42、without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is acc

43、essible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only.Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. I

44、t may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Repr

45、oducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Onli

46、ne (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase

47、price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becom

48、ing a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your

49、 documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 34