EN ISO 105-J02-2000 en Textiles - Tests for Colour Fastness - Part J02 Instrumental Assessment of Relative Whiteness《纺织品 色牢度试验 第J02部分 相关白色的指导评定 ISO 105-J02-1997 包括技术勘误1-1996》.pdf

《EN ISO 105-J02-2000 en Textiles - Tests for Colour Fastness - Part J02 Instrumental Assessment of Relative Whiteness《纺织品 色牢度试验 第J02部分 相关白色的指导评定 ISO 105-J02-1997 包括技术勘误1-1996》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 105-J02-2000 en Textiles - Tests for Colour Fastness - Part J02 Instrumental Assessment of Relative Whiteness《纺织品 色牢度试验 第J02部分 相关白色的指导评定 ISO 105-J02-1997 包括技术勘误1-1996》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、STD*BSI BS EN IS0 LOS-J02-ENGL 2000 Lb24bb9 08b1844 IT9 BRITISH STANDARD Textiles - Tests for colour fastness - Part 502: Instrumental assessment of relative whiteness The European Standard EN IS0 105502: 1999 has the status of a British Standard ICs 59.080.01 3s EN IS0 105- J02:ZOOO NO COPYING WITH

2、OUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW STD-BSI BS EN IS0 LOS-J02-ENGL 2000 - Lb24bb9 08bL845 035 m been prepared under the direction of the Sedor Committee for Materiais and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 August 20

3、00 Amd. No. O BSI 082 ISBN O 580 36125 X BS EN IS0 106302:2000 Date Comments National foreword This British Standard is the official English language version of EN IS0 105JOZ1999. It is identical with IS0 1055021997. It SuPeisedes method JO2 ofBS 1W1990. The UK participation in its preparation was e

4、ntrusted to Technical Committee TCv81, Colour fastness and colour measurement, which has the responsibility to: - aid enquirers to understand the te* - present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests

5、informed; - monitor related internalional and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC standards normally include an ann

6、ex which lists nonnative references to internaonal publications with their corresponding European publications. The British Standads which implement these internationai or European publications may be found in the BSI Standards Catalogue under the section entitled “International standards Correspond

7、ence Index“, or by using the “Find“ facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include ali the necessary provisions of a contsact. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of

8、itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN IS0 title page, the EN IS0 foreword page, the IS0 title page, page ii, pages 1 to 8, the annex ZA page and a back cover. The BSI copynght notice displayed in this docu

9、ment indicates when the document was last issued. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM STD.BSI BS EN IS0 105-JO2-ENGL 2000 = 1624667 O86184b T71 111 EN IS0 105302 May 1999 ICs 59.080.01 English version Textiles - Tests for colour fastness - Part J02: Instrumental assessment of relative

10、whiteness (IS0 105-J02:1997, including Technical Corrigendum 1 :1998) Textiles - Essais de solidit des teintures - Partie J02: Evaluation instrumentale de la blancheur relative (IC0 105- J02:1997, Rectificatif Technique 1:1998, inclus) Textilien - Farbechtheitspruhrngen - Teil JM: Instrumentelle Bes

11、timmung des relativen Weigrades (IS0 105-502: 1997, einschlielich Technische Korrektur 1 :1998) This European Standard was approved by CEN on 18 April 1999. CEN members are bound to comply with the CEWCENELEC Internal Regulations which stipulate the conditions for giving this European Standard aie s

12、tatus of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German).

13、A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the Official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland

14、, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal. Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMiTEE FOR STANDARDLXTION COMITE EUROPEEN DE NORMALISATION EUROPAISCHES KOMITEE FUR NORMUNG Central Secretariat: rue de Stassart. 36 8-1050 Brussel

15、s 0 1999 CEN All rights of exploitation in any form and by any means resewed worldwide for CEN national Members. Ref. No. EN IS0 105-J02:1999 E Foreword The text of the International Standard from Technical Committee ISOTTC 38 Textiles of the International Organization for Standardization (ISO) has

16、been taken over as an European Standard by Technical Committee CEN/TC 248 “Textiles and textile products“, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by

17、November 1999, and conflicting national standards shall be withdrawn at the latest by November 1999. According to the CENEENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denm

18、ark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard IS0 105-J02:1997 has been approved by CEN as a European Standard without any modific

19、ation. NOTE: Normative references to International Standards are listed in annex ZA (normative). STD=BSI BS EN IS0 LOS-JOZ-ENGL 2000 M I1624669 0863848 844 EN IS0 105-502:1999 INTERNATIONAL IS0 STANDARD 1051J02 Second edition 1997-1 2-1 5 Textiles - Tests for colour fastness - Part J02: Instrumental

20、 assessment of relative whiteness Textiles - Essais de solidit des teintures - Pattie J02: valuation instrumentale de la blancheur relative Reference number IS0 105-J02:1997(E) EN IS0 105-502:1999 Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national

21、 standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Internationa

22、l organizations, governmental and non- governmental, in liaison with ISO, also take pari in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committee

23、s are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard IS0 105-JO2 was prepared by Technical Committee ISOTTC 38, Textiles, Subcommittee SC 1, Tests for coloured textile

24、s and colorants. This second edition cancels and replaces the first edition (IS0 105-J02:1987), which has been technically revised. IS0 105 was previously published in thirteen “paris”, each designated by a letter (e.9. “Part A), with publication dates between 1978 and 1985. Each part contained a se

25、ries of “sections”, each designated by the respective part letter and by a two-digit serial number (e.g. “Section A01”). These sections are now being republished as separate documents, themselves designated “parts” but retaining their earlier alphanumeric designations. A complete list of these paris

26、 is given in IS0 105-AO1. Annex A forms an integral pari of this part of IS0 105. STD.BS1 BS EN IS0 LOS-JO2-ENGL 2000 = Zb24bb 0863850 4T2 EN IS0 106-502:1999 Textiles - Tests for colour fastness - Part J02: Instrumental assessment of relative whiteness 1 Scope 1.1 This part of IS0 105 specifies a m

27、ethod intended for quantifying the whiteness and tint of textiles, including fluorescent materials. 1.2 average viewer. Tint, if other than zero, is an indication of a reddish or greenish hue having shifted away from a bluish (neutral) hue with a dominant wavelength of 466 nm. The formulae for calcu

28、lation of whiteness and tint are those recommended by the CIEi). Whiteness as measured by this test method is an indication of how white the textile appears to an 1.3 only between specimens of the same type of textile. Because reflectance is affected by the nature of the surface of the textile, comp

29、arisons can be made 1.4 The application of the formulae is restricted to specimens that are called “white“ commercially, that do not differ much in colour and fluorescence and that are measured on the same instrument at nearly the same time. Within these restrictions, the formulae provide relative,

30、but not absolute, evaluations of whiteness that are adequate for commercial use when employing measuring instruments having suitable modern and commercially available capabilities. i) International Commission on Illumination, Vienna. 1 - STDmBSI BS EN IS0 105-J02-ENGL 2000 - LbZLibbq OBbL85L 339 W E

31、N IS0 106-502:1999 1.5 Many impurities in textiles absorb short wavelength light, resulting in a yellowish appearance to observers. Therefore, a measurement of whiteness may be an indication of the degree to which a textile is free from impurities. 1.6 The effect of blueing components or fluorescent

32、 whitening agents (FWAs) on the whiteness of textiles may also be determined using the whiteness measurement. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of IS0 105. At the time of publication, the editio

33、ns indicated were valid. All standards are subject to revision, and parties to agreement based on this part of IS0 105 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of the IEC and IS0 maintain registers of currently valid

34、 International Standards. IS0 105-JO1 :-2), Textiles - Test for colour fastness - Part JOI: General principles for measurement of sur 0,3 13 8 and 0,33 1 O are, respectively, the xi, and y, chromaticity coordinates for the perfect reflecting diffuser. is the whiteness value or index; is the tristimu

35、lus value of the specimen; 8.4 Tint (for Illuminant D, and 1964 10“ observer): T,., = 900 (0.3 13 8 - x,) - 650 (0,33 1 O -yili) 6 STD.BSI BS EN IS0 LOS-J02-ENGL 2000 1624669 ObL5b 710 EN IS0 106-502:1999 where Tw, is the tint value; x, and y, are the chromaticity coordinates of the specimen; 0,3 13

36、 8 and 0,33 1 O are, respectively, the x, and y, chromaticity coordinates for the perfect reflecting diffuser. Values of Tw, when positive indicate a greenish hue, when negative indicate a reddish hue and when zero indicate a bluish (neutral) hue with a dominant wavelength of 466 nm. 9 Testreport Re

37、port the relative whiteness value , the tint value, if required, and the particulars specified in IS0 105-501. 10 Precision and bias 10.1 Precision. Precision for this test method has not been established. There is no contemplated activity to establish precision for this method. Users of the method

38、should use standard statistical techniques in making any comparisons of test results for either within-laboratory or between-laboratory averages. 10.2 Bias. The whiteness and tint of textiles can be defined only in terms of a test method. There is no independent method for determining the true value

39、s. As a means of estimating these properties, the method has no known bias. 7 STDmBSI BS EN IS0 205-JOZ-ENGL 2000 E Lh24bb9 0861857 857 EN IS0 106-502:1999 Annex A (normative) Method for Illuminant C/2“ observer Tristimulus colorimeters typically do not conform to CIE Iilluminant Dh5 and the CIE 196

40、4 10“ observer. Most produce calculations for CIE Illuminant C and the CIE 193 1 2“ observer. Although the CIE Publication 15.2 recognizes whiteness and tint calculations for the CIE 1931 2“ observer, it does not recognize calculations for the CIE Illuminant C. Therefore, the following equations are

41、 given for those users of tristimulus colorimeters that have no other choice but to perform calculations for Illuminant C and the 193 1 2“ observer. Bear in mind however, that these calculations are to be used only for relative “in-house“ measurements and comparisons (see NOTES 1 and 2 in 8.2). For

42、FWA-treated specimens, the use of illuminant C may give misleading results with respect to visual assessments., Whiteness (For Illuminant C and 193 1 2“ observer): Wc,2=Y+800(0,310 1 -x)+ 170(0,316 1 -y) where iVc.2 is the whiteness value or index; Y x and y are the chromaticity coordinates of the s

43、pecimen; 0,3 10 1 and 0,3 16 1 are, respectively, the x and y chromaticity coordinates for the perfect reflecting diffuser. is the tristimulus value of the specimen; Tint (For Illuminant C and 1931 2“ observer): Tc,2=l 000(0,310 1-)-650(0,316 1 -y) where Tc,2 is the tint value; x and y are the chrom

44、aticity coordinates of the specimen; 0,3 10 1 and 0.3 16 1 are, respectively, the x and y chromaticity coordinates for the perfect reflecting diffuser. Values of Tel, when positive indicate a greenish hue, when negative indicate a reddish hue and when zero indicate a bluish (neutral) hue with a domi

45、nant wavelength of 466 nm. a STD-BSI BS EN IS0 LOS-JOZ-ENGL 2000 Lb24bb9 08bL858 793 EN IS0 106-502:1999 Annex ZA (normative) Normative references to international publications with their relevant European publications This European Standard incorporates by dated or undated reference, provisions fro

46、m other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendme

47、nt or revision. For undated references the latest edition of the publication referred to applies. Publication Year - EN - Year IS0 105-JO1 1997 Textiles - Tests for colour EN IS0 105-JO1 1999 fastness -Part JO1: General principles for measurement of surface colour STD.BS1 BS EN IS0 LOS-JO2-ENGL 2000

48、 m Lb24bb9 0862859 b2T m BS EN IS0 105402:2000 BSI 389ChiswickHighRoad London w4 4AL BSI - British Standards Institution BSI is the independent national body responsible for preparing Brim Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by

49、 Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant alln of BSI to improve the quality of our products and services. We would be grateful if anyone ndmg an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: O20 8996 9OOO. Fax: 020 8996 7400. BSI of