EN 62005-4-1999 en Reliability of Fibre Optic Interconnecting Devices and Passive Optical Components Part 4 Product Screening《光纤互连器件和无源器件的可靠性 第4部分 产品筛选 IEC 62005-4 1999》.pdf

《EN 62005-4-1999 en Reliability of Fibre Optic Interconnecting Devices and Passive Optical Components Part 4 Product Screening《光纤互连器件和无源器件的可靠性 第4部分 产品筛选 IEC 62005-4 1999》.pdf》由会员分享，可在线阅读，更多相关《EN 62005-4-1999 en Reliability of Fibre Optic Interconnecting Devices and Passive Optical Components Part 4 Product Screening《光纤互连器件和无源器件的可靠性 第4部分 产品筛选 IEC 62005-4 1999》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、STDeBSI BS EN b2005-4-ENGL 2000 Lb24bb7 0827338 128 BRITISH STANDARD Reliability of fibre optic interconnecting devices and passive optical components - Part 4: Product screening The European Standard EN 620054.1999 has the status of a British Standard ICs 33.180.20 NO COPYING WITHOUT BSI PERMISSION

2、 EXCEPT AS PEEMITED BY COPYRIGHT LAW BS EN 62005-4:2000 EC 620054.1999 STD-BSI BS EN b2005-4-ENGL 2000 Lb24669 0829339 Ob4 BS EN 62006-4:2000 direction of the Electrotechnicai Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 March 2000 hd. No

3、. This British Standard is the official English language version of EN 620054: 1999. It is identical with IEC 6200541999. The UK participation in its preparation was entrusted by Technical Committee GEM, Fbre optics, to Subcommittee GEL/86/2, interconnecting devices and passive components, which has

4、 the responsibility to: D - present to the responsible inkrnational/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; - monitor related intemational and European developments and promulgate ULtiii Li ilte un A ist of organizations re

5、presented on this subcommittee can be obtained on request to its secretary. From 1 January 1997, all IEC publications have the number 60000 added to the old number. For instance, IEC 27-1 has been renumbered as IEC 60027-1. For a period of time during the change over from one numbering system to the

6、 other, publications may contain identifiers from both systems. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to inkrna,tional publications with their corresponding European publications. The British Standard

7、s which implement these international or European publications may be found in the BSI Standars Catalogue under the section entitled “International Standards Correspondence Index“, or by using the “Find facility of the BSI Stanhds Electronic Catalogue. A British Standard does not purport to include

8、ali the necessasy provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages lus document comprises a front cover, an inside front cover, the EN tit

9、ie page, pages 2 to 5 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. O BSI 03-2000 I I ISBN O 580 34045 7 - STD-BSI BS EN 62005-4-ENGL 2000 Lb246b9 0829320 886 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 62005-4 November 19

10、99 ICs 33.1 80.20 English version Reliability of fibre optic interconnecting devices and passive optical components Part 4: Product screening (IEC 62005-4: 1 999) Fiabilit des dispositifs dinterconnexion et des composants optiques passifs fibres optiques Verbindungselemente und Partie 4: Slection de

11、s produits (CE1 62005-41999) Teil 4: Produktsortierprfung Betrie bszuverlssig keit von Lichtwellenleitern passive Bauteile (IEC 62005-41999) This European Standard was approved by CENELEC on 1999-1 0-01. CENELEC members are bound to comply with the CENICENELEC Internal Regulations which stipulate th

12、e conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exist

13、s in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electr

14、otechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de No

15、rmalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stasssrt 35, B - 1050 Brussels 1999 CENELEC - All rights of emploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 62005-41999 E STD.BSI BS EN b2005-4-ENGL

16、 2000 = lib24bb7 0827323 732 Page 2 EN 62005-4: 1 999 Foreword The text of document 866/121 2/FDIS, future edition 1 of IEC 62005-4, prepared by SC 86B, Fibre optic interconnecting devices and passive components, of IEC TC 86, Fibre optics, was submitted to the IEC-CENELEC parallel vote and was appr

17、oved by CENELEC as EN 62005-4 on 1999-10-01. The following dates were fixed: - latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement with the EN have to be withdrawn - Iztze? Atz hich il roLi -Lai wids c,rifikiirig - id

18、entify stress limits of product design and materials, and ensure that the tests selected are within safe limits; identify the earliest possible step in the process to apply the screen process; validate the screen - effective and harmless to good products: 1) run the screen on a sample population of

19、product with known or deliberately induced defects of the type addressed by the screen. Ensure that the screening test effectively identifies defective products with a low rejection of good products; 2) run the screen on a “good“ population several times, then lifetest this population versus an unsc

20、reened population, to ensure that no unacceptable degradation in the product due to the performance of the screen has occurred; as the screen is implemented in normal production, track and report product fallout; f) continue to validate the relevance of a screen on an ongoing basis. O BSI 03-2000 Pa

21、ge 5 EN 62005-41999 4 Types of screens Screens are specific conditions designed to address known and understood failure mechanism(s). In that context, they can be any or all of the types shown below. The following list is not exhaustive, but merely provided for illustrative purposes: - thermal (prol

22、onged temperature); - thermal cycling; - humidity; - mechanical shock; - mechanical tension; - mechanical vibration. Where thermal cycling is applied in addition to other perturbations, it is recommended that thermal cycling be performed after mechanical tests, such as vibration. Parts which may be

23、affected by mechanical perturbation may appear good at normal laboratory temperature, but in fact may fail at lower or higher temperature extremes. The screens shall not have accelerated effects. The duration of screens shall be selected to put in evidence and to eliminate defects without affecting

24、component lifetime. 5 Ongoing validation of screen effectiveness Product screening is a process, not a test. As such, it requires ongoing validation of its effectiveness. This starts with monitoring product failure rates in processes and reactions to changes in those failure rates. It is possible th

25、at, with time and improvement of processes or materials, the screen no longer produces fallout of products, because the failure mechanism(s) have been eliminated in the process. In that case, the screen can be successfully eliminated. It is also possible that, with changes to processes or materials

26、over time, the level of severity or degree of acceleration may no longer be appropriate. Also, it is possible that degradation of the product by the screen may have begun to occur. For that reason, ongoing validation of the screen and its relationship to the failure mechanism(s) in question should b

27、e performed. 6 Conclusion Screening is a potential alternative to product redesign, in order to minimize early failures in a product population. Screens shall be properly applied to ensure that no degradation of product lifetime or effectiveness related to the failure mechanism(s) in question occurs

28、. Screens used on products shall also be maintained and validated on an ongoing basis, to ensure their effectiveness and relevance over time. Screening is a choice which shall never be mandatory, but chosen in the context of proper use, as a cost effective alternative to product design improvements.

29、 O BSI 03-2000 BS EN 6200542000 IEC 62005-4:1999 BSI 389 Chiswick High Road London w4 4AL BSI Rritish Star,dards BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the intemational level. It is incorporated by Royal

30、 Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an in

31、accuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel 020 8996 9OoO. Fax2 ?4%, BSI offers members an individual updating service caled PLUS which ensures that subscr

32、ibers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel O20 8996 9001. Fax: 020 8996 7001. In response to orders for intemational standards, it is BSI policy to s

33、upply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on nationai, European and intemational standards through its Library and its Technical Help to Exporters Service. Various

34、 BSI electronic information services are also available which give details on all its products and services. Contact the information Centre. Tel 020 8996 7111. Fax: O20 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purc

35、hase price of standars. For details of these and other benefits contact Membership Administsati on Tel 020 8996 7002. Fax: O20 8996 7001. Copyright Copyright subsists in ail BSI publications. BSI also holds the copyright, in the UK, of the publications of the intemationai standarchtion bodies. Excep

36、t as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recordmg or otherwise - without prior written permission from BSI. This does not preclude the free use, i

37、n the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permiscion is granted, the tem may include royalty payments or a licensuig agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.