EN 61169-58-2016 en Radio-frequency connectors - Part 58 Sectional specification for RF coaxial connectors with blind-mate coupling - Characteristic impedance 50 (type SBMA).pdf

《EN 61169-58-2016 en Radio-frequency connectors - Part 58 Sectional specification for RF coaxial connectors with blind-mate coupling - Characteristic impedance 50 (type SBMA).pdf》由会员分享，可在线阅读，更多相关《EN 61169-58-2016 en Radio-frequency connectors - Part 58 Sectional specification for RF coaxial connectors with blind-mate coupling - Characteristic impedance 50 (type SBMA).pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、Radio-frequency connectorsPart 58: Sectional specification for RF coaxial connectors with blind-mate coupling Characteristic impedance 50 (type SBMA)BS EN 61169-58:2016BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06National forewordThis British Standard is the UK im

2、plementation of EN 61169-58:2016. It isidentical to IEC 61169-58:2016. The UK participation in its preparation was entrusted to TechnicalCommittee EPL/46, Cables, wires and waveguides, radio frequency connectors and accessories for communication and signalling.A list of organizations represented on

3、this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 87768 1ICS

4、 33.120.30Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 December 2016.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 61

5、169-58:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61169-58 November 2016 ICS 33.120.30 English Version Radio-frequency connectors - Part 58: Sectional specification for RF coaxial connectors with blind-mate coupling - Characteristic impedance 50 O (type SBMA) (IEC 61169-58:2016) Connec

6、teurs pour frquences radiolectriques - Partie 58: Spcification intermdiaire relative aux connecteurs coaxiaux pour frquences radiolectriques accouplement en aveugle - Impdance caractristique 50 O (type SBMA) (IEC 61169-58:2016) Hochfrequenz-Steckverbinder - Teil 58: Rahmenspezifikation fr koaxiale H

7、F-Steckverbinder mit Blindsteckverbindung - Wellenwiderstand 50 O (Typ SBMA) (IEC 61169-58:2016) This European Standard was approved by CENELEC on 2016-09-20. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standar

8、d the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (Engli

9、sh, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of

10、Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,

11、Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CENELEC All rights

12、 of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 61169-58:2016 E BS EN 61169-58:2016EN 61169-58:2016 2 European foreword The text of document 46F/347/FDIS, future edition 1 of IEC 61169-58, prepared by SC 46F “RF and microwave passive components“, of

13、IEC/TC 46 “Cables, wires, waveguides, RF connectors, RF and microwave passive components and accessories“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61169-58:2016. The following dates are fixed: latest date by which the document has to be implemented at national lev

14、el by publication of an identical national standard or by endorsement (dop) 2017-06-20 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2019-09-20 Attention is drawn to the possibility that some of the elements of this document may be the subject o

15、f patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61169-58:2016 was approved by CENELEC as a European Standard without any modification. BS EN 61169-58:2016EN 61169-58:2016 3

16、Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited app

17、lies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of

18、the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 61169-1 2013 Radio-frequency connectors - Part 1: Generic specification - General requirements and measuring methods EN 61169-1 2013 IEC 62037-3 - Passive RF and microwave devices, in

19、termodulation level measurement - Part 3: Measurement of passive intermodulation in coaxial connectors EN 62037-3 - BS EN 61169-58:2016 2 IEC 61169-58:2016 IEC 2016 CONTENTS FOREWORD . 4 1 Scope 6 2 Normative references. 6 3 Mating face and gauge information . 7 3.1 Dimensions General connectors . 7

20、 3.1.1 Connector with socket centre contact . 7 3.1.2 Connector with socket-centre contact . 8 3.2 Gauges for general purpose connectors . 9 3.2.1 Gauge pins for socket centre contact 9 3.2.2 Test procedure . 10 3.2.3 Gauge pins for outer contact 10 3.2.4 Test procedure . 11 3.3 Dimensions standard

21、test connectors grade 0 11 3.3.1 Connector with pin-centre contact. 11 3.3.2 Connector with socket-centre contact . 12 3.4 Requirements for installation . 12 3.4.1 Radial misalignment . 12 3.4.2 Axial separation between mating reference planes 13 4 Quality assessment procedures . 14 4.1 General . 14

22、 4.2 Ratings and characteristics (see Clause 5 of IEC 61169-1:2013) 14 4.3 Test schedule and inspection requirements 16 4.3.1 Acceptance tests 16 4.3.2 Periodic tests . 16 4.4 Procedures for the quality conformance . 19 4.4.1 Quality conformance inspection 19 4.4.2 Qualification approval and its mai

23、ntenance . 19 5 Instructions for preparation of detail specifications . 19 5.1 General . 19 5.2 Identification of the component 19 5.3 Performances 19 5.4 Marking, ordering information and related matters 20 5.5 Selection of tests, test conditions and severities 20 5.6 Blank detail specification pro

24、-forma for type SMBA connector 20 6 Marking . 24 6.1 Marking of component . 24 6.2 Marking and contents of package 25 Figure 1 Connector with pin centre contact (for dimensions, see Table 1) 7 Figure 2 Connector with socket centre contact (for dimensions, see Table 2) 8 Figure 3 Gauge pin for socket

25、-centre contact (for dimensions, see Table 3) 9 Figure 4 Gauge pin for outer contact (for dimensions, see Table 4) . 10 Figure 5 Connector with pin centre contact (for dimensions, see Table 5) 11 Figure 6 Connector with socket centre contact (for dimensions, see Table 6) 12 Figure 7 Radial misalignm

26、ent . 13 BS EN 61169-58:2016IEC 61169-58:2016 IEC 2016 3 Figure 8 Rigidly mounted receptacle and jack . 13 Figure 9 Rigidly mounted receptacle and float mounted jack . 14 Table 1 Dimensions of connector with pin-centre contact 8 Table 2 Dimensions of connector with socket-centre contact . 9 Table 3

27、Gauge pins dimensions for socket-centre contact . 9 Table 4 Gauge pins dimensions for outer contact 10 Table 5 Dimensions of connector with pin-centre contact 11 Table 6 Dimensions of connector with socket-centre contact . 12 Table 7 Rating and characteristics 15 Table 8 Acceptance tests . 17 Table

28、9 Periodic tests 18 BS EN 61169-58:2016 4 IEC 61169-58:2016 IEC 2016 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ RADIO-FREQUENCY CONNECTORS Part 58: Sectional specification for RF coaxial connectors with blind-mate coupling Characteristic impedance 50 (type SBMA) FOREWORD 1) The International Electr

29、otechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. T

30、o this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC Nati

31、onal Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (I

32、SO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation

33、from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be

34、 held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. An

35、y divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access t

36、o IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individu

37、al experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, thi

38、s IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of thi

39、s IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61169-58 has been prepared by subcommittee 46F: RF and microwave passive components, of IEC technical committee 46: Cables, wires, wavegu

40、ides, RF connectors, RF and microwave passive components and accessories. The text of this standard is based on the following documents: FDIS Report on voting 46F/347/FDIS 46F/352/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in t

41、he above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. BS EN 61169-58:2016IEC 61169-58:2016 IEC 2016 5 A list of all parts of the IEC 61169 series, under the general title: Radio-frequency connectors, can be found on the IEC website. The committee has de

42、cided that the contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amend

43、ed. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. BS EN 61169-58:2016 6 IEC 61169-58:2016 IE

44、C 2016 RADIO-FREQUENCY CONNECTORS Part 58: Sectional specification for RF coaxial connectors with blind-mate coupling Characteristic impedance 50 (type SBMA) 1 Scope This part of IEC 61169, which is a sectional specification (SS), provides information and rules for the preparation of detail specific

45、ations (DS) for SBMA series coaxial connectors with blind-mate coupling. The connectors are used with cables with characteristic impedance 50 in an operating frequency range up to 28 GHz. The connectors are widely used in communications, antennas, radars and other applications for modules interconne

46、ctions. It is also normally used in conjunction with appropriate transmission line. It describes the interface dimensions for general purpose connectors with gauging information and the mandatory tests selected from IEC 61169-1, applicable to all detail specifications relative to type SBMA connector

47、s. This specification indicates the recommended performance characteristics to be considered when writing a DS and covers all tests schedules and inspection requirements. NOTE Dimension are in mm, however original dimensions were in inches. All un-dimensioned pictorial configurations are for referen

48、ce purpose only. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (in

49、cluding any amendments) applies. IEC 61169-1:2013, Radio-frequency connectors Part 1: Generic specification General requirements and measuring methods IEC 62037-3, Passive RF and microwave devices, intermodulation level measurement Part 3: Measurement of passive intermodulation in coaxial connectors BS EN 61169-58:2016IEC 61169-58:2016 IEC 2016 7 3 Mating face and gauge information 3.1 Dimensions General connectors 3.1.1 Connect