EN 60384-3-2016 en Fixed capacitors for use in electronic equipment - Part 3 Sectional specification - Surface mount fixed tantalum electrolytic capacitors with solid (MnO2) electr.pdf

《EN 60384-3-2016 en Fixed capacitors for use in electronic equipment - Part 3 Sectional specification - Surface mount fixed tantalum electrolytic capacitors with solid (MnO2) electr.pdf》由会员分享，可在线阅读，更多相关《EN 60384-3-2016 en Fixed capacitors for use in electronic equipment - Part 3 Sectional specification - Surface mount fixed tantalum electrolytic capacitors with solid (MnO2) electr.pdf（36页珍藏版）》请在麦多课文档分享上搜索。

1、Fixed capacitors for use in electronic equipment Part 3: Sectional specification: Surfacemount fixed tantalum electrolyticcapacitors with solid (MnO2) electrolyteBS EN 60384-3:2016BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06National forewordThis British Standard

2、is the UK implementation of EN 60384-3:2016. It is identical to IEC 60384-3:2016. It supersedes BS EN 60384-3:2006 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee EPL/40X, Capacitors and resistors for electronic equipment.A list of organizations represe

3、nted on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 84

4、246 7ICS 31.060.30Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 October 2016.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDB

5、S EN 60384-3:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60384-3 October 2016 ICS 31.060.30 Supersedes EN 60384-3:2006 English Version Fixed capacitors for use in electronic equipment - Part 3: Sectional specification - Surface mount fixed tantalum electrolytic capacitors with solid (Mn

6、O2) electrolyte (IEC 60384-3:2016) Condensateurs fixes utiliss dans les quipements lectroniques - Partie 3: Spcification intermdiaire - Condensateurs fixes lectrolytiques au tantale pour montage en surface, lectrolyte solide (MnO2) (IEC 60384-3:2016) Festkondensatoren zur Verwendung in Gerten der El

7、ektronik - Teil 3: Rahmenspezifikation - Oberflchenmontierbare Tantal-Kondensatoren mit festem (MnO2)-Elektrolyt (IEC 60384-3:2016) This European Standard was approved by CENELEC on 2016-08-16. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditio

8、ns for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exist

9、s in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the natio

10、nal electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Port

11、ugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-10

12、00 Brussels 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 60384-3:2016 E BS EN 60384-3:2016EN 60384-3:2016 2 European foreword The text of document 40/2464/FDIS, future edition 4 of IEC 60384-3, prepared by IEC/TC 40 “Capacit

13、ors and resistors for electronic equipment“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60384-3:2016. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endor

14、sement (dop) 2017-05-16 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2019-08-16 This document supersedes EN 60384-3:2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENE

15、LEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60384-3:2016 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following not

16、e has to be added for the standard indicated : IEC 60068-2-58:2015 NOTE Harmonized as EN 60068-2-58:2015 (not modified). BS EN 60384-3:2016EN 60384-3:2016 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents,

17、 in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Pu

18、blication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 60062 - Marking codes for

19、resistors and capacitors EN 60062 - IEC 60063 - Preferred number series for resistors and capacitors EN 60063 - IEC 60068-1 2013 Environmental testing - Part 1: General and guidance EN 60068-1 2014 IEC 60384-1 2016 Fixed capacitors for use in electronic equipment - Part 1: Generic specification EN 6

20、0384-1 2016 IEC 60417 - Graphical symbols for use on equipment - - IEC 61193-2 2007 Quality assessment systems - Part 2: Selection and use of sampling plans for inspection of electronic components and packages EN 61193-2 2007 ISO 3 - Preferred numbers - Series of preferred numbers - - BS EN 60384-3:

21、2016 2 IEC 60384-3:2016 IEC 2016 CONTENTS FOREWORD . 5 1 General . 7 1.1 Scope . 7 1.2 Object . 7 1.3 Normative references 7 1.4 Information to be given in a detail specification 8 1.4.1 General . 8 1.4.2 Outline drawing and dimensions . 8 1.4.3 Mounting 8 1.4.4 Ratings and characteristics 8 1.4.5 M

22、arking . 9 1.5 Terms and definitions 9 1.6 Marking . 9 1.6.1 General . 9 1.6.2 Information for marking 9 1.6.3 Marking on capacitors 9 1.6.4 Marking on packaging 10 2 Preferred ratings and characteristics 10 2.1 Preferred characteristics . 10 2.2 Preferred values of ratings 10 2.2.1 Nominal capacita

23、nce (CN) 10 2.2.2 Tolerance on nominal capacitance 11 2.2.3 Rated voltage (UR) . 11 2.2.4 Category voltage (UC) 11 2.2.5 Surge voltage (URSor UCS) 11 2.2.6 Rated temperature . 11 3 Quality assessment procedures . 12 3.1 Primary stage of manufacture 12 3.2 Structurally similar components . 12 3.3 Cer

24、tified test records of released lots 12 3.4 Qualification approval procedures 12 3.4.1 General . 12 3.4.2 Qualification approval on the basis of the fixed sample size procedure 12 3.4.3 Tests . 13 3.5 Quality conformance inspection . 20 3.5.1 Formation of inspection lots 20 3.5.2 Test schedule 20 3.

25、5.3 Delayed delivery 20 3.5.4 Assessment levels . 20 4 Test and measurement procedures 21 4.1 Drying . 22 4.2 Measuring conditions 22 4.3 Mounting . 22 4.3.1 General . 22 4.3.2 Initial inspection . 22 4.3.3 Final inspections 22 BS EN 60384-3:2016IEC 60384-3:2016 IEC 2016 3 4.4 Visual examination and

26、 check of dimensions . 22 4.4.1 General . 22 4.4.2 Visual examination and check of dimensions 22 4.4.3 Requirements 22 4.5 Electrical tests 22 4.5.1 Leakage current . 22 4.5.2 Capacitance . 23 4.5.3 Tangent of loss angle (tan ) 23 4.5.4 Impedance (if required) 23 4.5.5 Equivalent series resistance (

27、ESR) (if required) 24 4.6 Resistance to soldering heat . 24 4.6.1 General . 24 4.6.2 Test conditions 24 4.6.3 Recovery . 24 4.6.4 Final inspections and requirements 25 4.7 Solderability 25 4.7.1 General . 25 4.7.2 Test conditions 25 4.7.3 Final inspections and requirements 25 4.8 Shear test . 25 4.8

28、.1 General . 25 4.8.2 Final inspections and requirements 25 4.9 Substrate bending test 25 4.9.1 General . 25 4.9.2 Final inspections and requirements 25 4.10 Rapid change of temperature 25 4.10.1 General . 25 4.10.2 Initial inspection . 25 4.10.3 Test conditions 25 4.10.4 Recovery . 26 4.10.5 Final

29、inspections and requirements 26 4.11 Climatic sequence (if required) 26 4.11.1 General . 26 4.11.2 Initial inspections . 26 4.11.3 Dry heat . 26 4.11.4 Damp heat, cyclic, test Db, first cycle . 26 4.11.5 Cold . 26 4.11.6 Damp heat, cyclic, test Db, remaining cycles 26 4.11.7 Recovery . 26 4.11.8 Fin

30、al inspections and requirements 26 4.12 Damp heat, steady state (if required) . 26 4.12.1 General . 26 4.12.2 Initial inspections . 27 4.12.3 Test conditions 27 4.12.4 Recovery . 27 4.12.5 Final inspections and requirements 27 4.13 Characteristics at high and low temperature . 27 4.13.1 General . 27

31、 4.13.2 Inspections and requirements . 27 BS EN 60384-3:2016 4 IEC 60384-3:2016 IEC 2016 4.14 Surge voltage 27 4.14.1 General . 27 4.14.2 Initial inspections . 27 4.14.3 Test conditions 27 4.14.4 Recovery . 28 4.14.5 Final inspections and requirements 28 4.15 Endurance 28 4.15.1 General . 28 4.15.2

32、Initial inspections . 28 4.15.3 Test conditions 28 4.15.4 Recovery . 28 4.15.5 Final inspections and requirements 29 4.16 Reverse voltage (if required) . 29 4.16.1 Initial inspections . 29 4.16.2 Test conditions 29 4.16.3 Recovery . 29 4.16.4 Final inspections and requirements 29 4.17 Component solv

33、ent resistance (if required) 29 4.18 Solvent resistance of the marking (if required) . 29 4.19 High surge current (if required) 29 Bibliography . 30 Table 1 Letter code and digit 10 Table 2 Category voltages and surge voltages 11 Table 3 Sampling plan for qualification approval, assessment level EZ

34、14 Table 4 Test schedule for qualification approval . 15 Table 5 Lot-by-lot inspection 21 Table 6 Periodic inspection 21 Table 7 Test temperatures . 28 BS EN 60384-3:2016IEC 60384-3:2016 IEC 2016 5 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 3: S

35、ectional specification Surface mount fixed tantalum electrolytic capacitors with solid (MnO2) electrolyte FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The

36、 object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifi

37、cations (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations l

38、iaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters exp

39、ress, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Commi

40、ttees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC Nation

41、al Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does n

42、ot provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have

43、the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoev

44、er, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publicatio

45、ns is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard

46、 IEC 60384-3 has been prepared by IEC technical committee 40: Capacitors and resistors for electronic equipment. This fourth edition cancels and replaces the third edition published in 2006 and constitutes a technical revision. This edition includes the following significant technical changes with r

47、espect to the previous edition: a) Revision of the structure in accordance with ISO/IEC Directives, Part 2:2011 (sixth edition) to the extent practicable, and harmonization between other similar kinds of documents. b) In addition, Clause 4 and all the tables have been reviewed in order to prevent du

48、plications and contradictions. The text of this standard is based on the following documents: BS EN 60384-3:2016 6 IEC 60384-3:2016 IEC 2016 FDIS Report on voting 40/2464/FDIS 40/2470/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated

49、in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The list of all the parts of the IEC 60384 series, under the general title Fixed capacitors for use in electronic equipment, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this da