EN 60317-20-2014 en Specifications for particular types of winding wires - Part 20 Solderable polyurethane enamelled round copper wire class 155.pdf

《EN 60317-20-2014 en Specifications for particular types of winding wires - Part 20 Solderable polyurethane enamelled round copper wire class 155.pdf》由会员分享，可在线阅读，更多相关《EN 60317-20-2014 en Specifications for particular types of winding wires - Part 20 Solderable polyurethane enamelled round copper wire class 155.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationSpecifications for particular types of winding wiresPart 20: Solderable polyurethane enamelled round copper wire, class 155BS EN 60317-20:2014National forewordThis British Standard is the UK implementation of EN 60317-20:2014. It isidentical to IEC 60317-20:2013. It supersed

2、es BS EN 60317-20:1996 which iswithdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee GEL/55, Winding wires.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary p

3、rovisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 75752 5ICS 29.060.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was publis

4、hed under the authority of theStandards Policy and Strategy Committee on 28 February 2014.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 60317-20:2014EUROPEAN STANDARD EN 60317-20 NORME EUROPENNE EUROPISCHE NORM February 2014CENELEC European Committee for Elect

5、rotechnical StandardizationComit Europen de Normalisation ElectrotechniqueEuropisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels 2014 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

6、 Ref. No. EN 60317-20:2014 E ICS 29.060.10 Supersedes EN 60317-20:1995 + A1:1998 + A2:2000 English version Specifications for particular types of winding wires - Part 20: Solderable polyurethane enamelled round copper wire, class 155(IEC 60317-20:2013) Spcifications pour types particuliers defils de

7、 bobinage - Partie 20: Fil brasable de section circulaireen cuivre maill avec polyurthane,classe 155 (CEI 60317-20:2013) Technische Lieferbedingungen frbestimmte Typen von Wickeldrhten - Teil 20: Runddrhte aus Kupfer,verzinnbar, lackisoliert mit Polyurethan,Klasse 155 (IEC 60317-20:2013) This Europe

8、an Standard was approved by CENELEC on 2013-11-14. CENELEC members are bound to complywith the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standardthe status of a national standard without any alteration. Up-to-date lists and bibliographical references co

9、ncerning such national standards may be obtained onapplication to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any otherlanguage made by translation under the responsibility of a CENELEC m

10、ember into its own language and notifiedto the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republ

11、ic of Macedonia, France, Germany,Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Foreword The text of document 55/1411/FDIS, future editio

12、n 3 of IEC 60317-20, prepared by IEC/TC 55 “Winding wires“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60317-20:2014. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national stan

13、dard or by endorsement (dop) 2014-08-14 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2016-11-14 This document supersedes EN 60317-20:1995. EN 60317-20:2014 includes the following significant technical changes with respect to EN 60317-20:1995: n

14、ew 3.2.2 containing general notes on winding wire, formerly a part of the scope; revision to references to EN 60317-0-1:2014 to clarify that their application is normative; modification to Clause 15 to remove specific wire specimen sizes; consolidation of 17.1 and 17.2 of the solderability requireme

15、nts; modification to Clause 19, Dielectric dissipation factor; new Clause 23, Pin hole test. The numbering of clauses in this standard is not continuous from Clauses 20 and 30 in order to reserve space for possible future wire requirements prior to those for wire packaging. Attention is drawn to the

16、 possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60317-20:2013 was approved by CENELEC as a Europe

17、an Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60264 Series NOTE Harmonized as EN 60264 Series (not modified). IEC 60317 Series NOTE Harmonized as EN 60317 Series (not modified). IEC 60851 Series

18、NOTE Harmonized as EN 60851 Series (not modified). BS EN 60317-20:2014 EN 60317-20:2014Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and

19、are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod),

20、 the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60317-0-1 2013 Specifications for particular types of winding wires - Part 0-1: General requirements - Enamelled round copper wire EN 60317-0-1 2014 BS EN 60317-20:2014 EN 60317-20:2014 2 60317-20 IEC:2013 CONTENTS INTRODUCTION . 5 1

21、 Scope . 6 2 Normative references . 6 3 Terms, definitions, general notes and appearance 6 3.1 Terms and definitions 6 3.2 General notes 6 3.2.1 Methods of test 6 3.2.2 Winding wire 6 3.3 Appearance . 7 4 Dimensions 7 5 Electrical resistance . 7 6 Elongation 7 7 Springiness 7 8 Flexibility and adher

22、ence 7 9 Heat shock . 7 10 Cut-through 7 11 Resistance to abrasion (nominal conductor diameters from 0,250 mm up to and including 0,800 mm) . 7 12 Resistance to solvents 8 13 Breakdown voltage . 8 14 Continuity of insulation . 8 15 Temperature index . 8 16 Resistance to refrigerants . 8 17 Solderabi

23、lity . 8 17.1 Nominal conductor diameters up to and including 0,100 mm 8 17.2 Nominal conductor diameters over 0,100 mm 9 18 Heat or solvent bonding 9 19 Dielectric dissipation factor . 9 20 Resistance to transformer oil 9 21 Loss of mass 9 23 Pin hole test . 9 30 Packaging 9 Bibliography 10 Table 1

24、 Resistance to abrasion 8 BS EN 60317-20:2014 EN 60317-20:201460317-20 IEC:2013 5 INTRODUCTION This part of IEC 60317 is one of a series which deals with insulated wires used for windings in electrical equipment. The series has three groups describing: 1) Winding wires Test methods (IEC 60851); 2) S

25、pecifications for particular types of winding wires (IEC 60317); 3) Packaging of winding wires (IEC 60264). BS EN 60317-20:2014 EN 60317-20:2014 6 60317-20 IEC:2013 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 20: Solderable polyurethane enamelled round copper wire, class 155 1 Scope Th

26、is part of IEC 60317 specifies the requirements of solderable enamelled round copper winding wire of class 155 with a sole coating based on polyurethane resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. NOTE A mod

27、ified resin is a resin that has undergone a chemical change, or contains one or more additives to enhance certain performance or application characteristics. The range of nominal conductor diameters covered by this standard is: Grade 1: 0,018 mm up to and including 0,800 mm; Grade 2: 0,020 mm up to

28、and including 0,800 mm. The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-1:2013. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition

29、cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60317-0-1:2013, Specifications for particular types of winding wires Part 0-1: General requirements Enamelled round copper wire 3 Terms, definitions, general notes and appeara

30、nce 3.1 Terms and definitions Subclause 3.1 of IEC 60317-0-1:2013 applies. 3.2 General notes 3.2.1 Methods of test Subclause 3.2.1 of IEC 60317-0-1:2013 applies. In case of inconsistencies between IEC 60317-0-1:2013 and this part of IEC 60317, the latter shall prevail. 3.2.2 Winding wire Class 155 i

31、s a thermal class that requires a minimum temperature index of 155 and a heat shock temperature of at least 175 C. The temperature in degrees Celsius corresponding to the temperature index is not necessarily that at which it is recommended that the wire be operated and this will depend on many facto

32、rs, including the type of equipment involved. BS EN 60317-20:2014 EN 60317-20:201460317-20 IEC:2013 7 3.3 Appearance Subclause 3.3 of IEC 60317-0-1:2013 applies. 4 Dimensions Clause 4 of IEC 60317-0-1:2013 applies. 5 Electrical resistance Clause 5 of IEC 60317-0-1:2013 applies. 6 Elongation Clause 6

33、 of IEC 60317-0-1:2013 applies. 7 Springiness Clause 7 of IEC 60317-0-1:2013 applies. 8 Flexibility and adherence Clause 8 of IEC 60317-0-1:2013 applies. 9 Heat shock Clause 9 of IEC 60317-0-1:2013 applies. The minimum heat shock temperature shall be 175 C. 10 Cut-through No failure shall occur with

34、in 2 min at 200 C. 11 Resistance to abrasion (nominal conductor diameters from 0,250 mm up to and including 0,800 mm) The wire shall meet the requirements given in Table 1. For intermediate nominal conductor diameters, the value of the next larger nominal conductor diameter shall be taken. BS EN 603

35、17-20:2014 EN 60317-20:2014 8 60317-20 IEC:2013 Table 1 Resistance to abrasion Nominal conductor diameter Grade 1 Grade 2 Minimum average force to failure Minimum force to failure of each measurement Minimum average force to failure Minimum force to failure of each measurement mm N N N N 0,250 2,30

36、1,95 4,10 3,50 0,280 2,50 2,10 4,40 3,70 0,315 2,70 2,30 4,75 4,00 0,355 2,90 2,50 5,10 4,30 0,400 3,15 2,70 5,45 4,60 0,450 3,40 2,90 5,80 4,90 0,500 3,65 3,10 6,20 5,25 0,560 3,90 3,30 6,65 5,60 0,630 4,20 3,55 7,10 6,00 0,710 4,50 3,80 7,60 6,45 0,800 4,80 4,10 8,10 6,90 12 Resistance to solvents

37、 Clause 12 of IEC 60317-0-1:2013 applies. 13 Breakdown voltage Clause 13 of IEC 60317-0-1:2013 applies. The elevated temperature shall be 155 C. 14 Continuity of insulation Clause 14 of IEC 60317-0-1:2013 applies. 15 Temperature index Clause 15 of IEC 60317-0-1:2013 applies. The minimum temperature

38、index shall be 155. 16 Resistance to refrigerants Test inappropriate. 17 Solderability 17.1 Nominal conductor diameters up to and including 0,100 mm The temperature of the solder bath shall be (390 5) C. The maximum immersion time shall be 2 s. BS EN 60317-20:2014 EN 60317-20:201460317-20 IEC:2013 9

39、 The surface of the tinned wire shall be smooth and free from holes and enamel residues. 17.2 Nominal conductor diameters over 0,100 mm The temperature of the solder bath shall be (390 5) C. The maximum immersion time (in seconds) shall be the following multiple of the nominal conductor diameter (in

40、 millimetres) with a minimum of 2 s. Grade 1 Grade 2 8 s/mm 12 s/mm The surface of the tinned wire shall be smooth and free from holes and enamel residues. 18 Heat or solvent bonding Test inappropriate. 19 Dielectric dissipation factor Test to be agreed between purchaser and supplier. 20 Resistance

41、to transformer oil Test inappropriate. 21 Loss of mass Test inappropriate. 23 Pin hole test Clause 23 of IEC 60317-0-1:2013 applies. 30 Packaging Clause 30 of IEC 60317-0-1:2013 applies. BS EN 60317-20:2014 EN 60317-20:2014 10 60317-20 IEC:2013 Bibliography IEC 60264 (all parts), Packaging of windin

42、g wires IEC 60317 (all parts), Specifications for particular types of winding wires IEC 60851 (all parts), Winding wires Test methods _ BS EN 60317-20:2014 EN 60317-20:2014This page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-relate

43、d publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together busines

44、s, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of a

45、ll sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowl

46、edge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development

47、 Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to ove

48、r 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy an

49、d subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are abl