EN 181101-1994 en Blank Detail Specification Fibre Optic Branching Devices Type Non Wavelength Selective Transmissive Star《空白详细规范 光纤分路器类型 非波长选择星型传送器》.pdf
《EN 181101-1994 en Blank Detail Specification Fibre Optic Branching Devices Type Non Wavelength Selective Transmissive Star《空白详细规范 光纤分路器类型 非波长选择星型传送器》.pdf》由会员分享,可在线阅读,更多相关《EN 181101-1994 en Blank Detail Specification Fibre Optic Branching Devices Type Non Wavelength Selective Transmissive Star《空白详细规范 光纤分路器类型 非波长选择星型传送器》.pdf(21页珍藏版)》请在麦多课文档分享上搜索。
1、. W 3404583 0151025 3T2 BS EN 181101 : 1995 Specification for Harmonized system of quality assessment for electronic components Blank detail specification Fibre optic branching devices Type: non wavelength selective transmissive star The European Standard EN 181101 : 1994 has the status of a British
2、 Standard oYri together with thevoting report, circulated as document CECC(Secretariat)3274, it was approved by CECC as EN 181 101 on 17 January 1993. The following dates were fixed: - latest date of announcement of the EN at national level - latest date of publication of an identical national stand
3、ard - latest date of declaration of national standards obsolescence - latest date of withdrawal of conflicting national standards 1993-041 4 199443-1 4 1994-03-1 4 200349-14 Page 3 EN 181 101: 1994 GUIDANCE FOR THE PREPARATION OF DETAIL SPECIFICATIONS 1 INTRODUCTION This specification is a BDS for F
4、ibre Optic Branching Devices of the “Non wavelength selective transmissive star“ type. This includes instructions for preparing a DS. 2 2.1 2.2 3 3.1 3.2 4 QUALIFICATION APPROVAL Procedure The DS shall state the qualification approval procedure to be used in accordance with clause 3.3 of EN 181 000.
5、 Test schedule and performance requirements The test schedule for qualification by the fixed sample procedure shall be given in table 1 of DS (see clauses 2.2, 4.5 and 4.6 of EN 181 000). QUALITY CONFORMANCE INSPECTION Lot-by-lot inspection The test schedule for lot-by-lot inspection (groups A and B
6、) shall be given in table 2 of the DS (see clauses 2.2, 4.5 and 4.6 of EN 181 000). Periodic inspection The test schedule for periodic inspection (groups C and D) shall be given in table 3 of the DS (See clauses 2.2, 4.5 and 4.6 of EN 181 000). PREPARATION OF DETAIL SPECIFICATIONS (DS) Each BDS is p
7、ublished separately as a pro forma document, with numbered spaces provided for entering the informa- tion necessary to create a DS. If the spaces provided are too small, then the information shall be provided on additional sheets forming part of the completed DS. Instructions for filling in the numb
8、ered spaces in a BDS are given below: (1) The name of the ONH under whose authority the DS is published and, if applicable, the organization from whom the DS is available. (2) The CECC symbol and the number allotted to the DS by the CECC General Secretariat. (3) The number and issue number of the CE
9、CC GS; also the national reference(s), if different. W 3404583 0151031 bTb W Page 4 EN 181 101: 1994 (4) If different from the CECC number, the national number of the DS, date of issue and any further information required by the national system, together with any amendment numbers. (5) A brief descr
10、iption of the component or range of components. (6) The level of quality assessment (A, B, C or X), sampling procedure (fixed quantity or lot-by-lot) and the climatic category. For (5) and (6) the text to be given in the DS shall be suitable for an entry in CECC O0 200 (Register of Approvals) and CE
11、CC O0 300 (Register of National Documents). (7) An outline drawing with main dimensions which are of importance for interchangeability, and/or reference to the appropriate national or international document for outlines. Alternatively, this drawing may be given in an annex to the DS, but (7) shall a
12、lways contain an illustration of the general outer appearance of the component. If an existing drawing from an IEC publication, or simi- lar source, is used in a CECC specification, then it can be either first or third angle projection, but the appro- priate symbol shall be shown on the drawing: Ist
13、 angle projection 3rd angle projection The symbol in the BDS may be converted to indicate either 1st or 3rd angle, by deleting the inappropriate part of the drawing. Alternative outline dimensions or tolerance limits of any variants shall be shown, and may be listed in the form of a table alongside
14、the drawing. (8) A list of variants and their identifying features covered by the DS. Enter the identification number. I1AYY“ for each variant of each component (see clause 2.7.1 of EN 181 000). Assign a column in the table for each variant feature. For example, cable type, housing, orientation of p
15、orts, means of mounting etc. Instruction: - max. values in dB for insertion losses between conduction ports; - min. values in dB for return losses; = 3404583 0151032 532 Page 5 EN 181 101: 1994 - min. values in dB for insertion losses between isolated ports. (9) Supplementary information Enter the s
16、upplementary information with respect to marking of the component, marking and contents of package, ordering information, related documents, certified test records and structural similarity. (10) Fixed-sample qualification approval test schedule Table 1 shall give the required measurements and tests
17、 for qualification by fixed-sample procedure. If qualification by lot-by-lot and periodic procedure is specified, insert “NOT APPLICABLE“ in table 1. If measurements or tests are specified for which no basic procedure is available, or which do not appear in the GS, EN 181 000, each procedure shall b
18、e clearly described in an individual annex to the DS. The format and the minimum mandatory test sequence shall be the same as specified in the GS. (11) Lot-by-lot inspection test schedule When completed, table 2 shall give the required measurements and tests for qualification by lot-by- lot procedur
19、e. One or more assessment level(s) shall be given in table 2. When differing from the prefer- red levels of the GS (see clause 2.1.5 of EN 181000) the IL and AQL shall be entered and the assessment level(s) titled X, (Y) . etc. If measurements or tests are specified for which no basic procedure is a
20、vailable, or which do not appear in the GS, EN 181 000, each procedure shall be clearly described in an individual annex to the DS. The format and the minimum mandatory test sequence shall be the same as specified in the GS. (12) Periodic C and D testing procedure Table 3 shall give the required mea
21、surements and tests for groups C and D periodic tests. One or more assessment level(s) shall be given in table 3. When differing from the preferred levels of the GS clause 2.1.5 of EN 181 000) the IL, AQL, p, n, c and t shall be entered and the assessment level(s) titled (X, Y). (see (13) Details, m
22、easurements, and performance requirements Table 4 shall list the details of each tests requirements. It shall be noted that the mandatory tests have been given as a minimum. Other tests shall be given in the same manner. W 3404583 0353033 479 (1) Specification available from Page 6 EN 181 101: 1994
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- EN1811011994ENBLANKDETAILSPECIFICATIONFIBREOPTICBRANCHINGDEVICESTYPENONWAVELENGTHSELECTIVETRANSMISSIVESTAR

链接地址:http://www.mydoc123.com/p-716304.html