EN 15534-5-2014 en Composites made from cellulose-based materials and thermoplastics (usually called wood-polymer composites (WPC) or natural fibre composites (NFC)) - Part 5 Speci.pdf

《EN 15534-5-2014 en Composites made from cellulose-based materials and thermoplastics (usually called wood-polymer composites (WPC) or natural fibre composites (NFC)) - Part 5 Speci.pdf》由会员分享，可在线阅读，更多相关《EN 15534-5-2014 en Composites made from cellulose-based materials and thermoplastics (usually called wood-polymer composites (WPC) or natural fibre composites (NFC)) - Part 5 Speci.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 15534-5:2014Composites made fromcellulose-based materials andthermoplastics (usually calledwood-polymer composites(WPC) or natural fibrecomposites (NFC)Part 5: Specifications for cladding profilesand tilesBS EN 15534-5:2014 BRITISH STANDARDNational forewordThis British

2、 Standard is the UK implementation of EN 15534-5:2014.Together with BS EN 15534-4:2014 it supersedes DD CEN/TS 15534-3:2007, which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/42, Fibre reinforced thermosetting plastics and prepregs.A list of organizat

3、ions represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2014.Published by BSI Standards Limited 2014ISB

4、N 978 0 580 79505 3ICS 79.080; 83.140.99Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2014.Amendments/corrigenda issued since publicationDate T e x t

5、a f f e c t e dBS EN 15534-5:2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15534-5 January 2014 ICS 79.080; 83.140.99 Supersedes CEN/TS 15534-3:2007English Version Composites made from cellulose-based materials and thermoplastics (usually called wood-polymer composites (WPC) or natural fi

6、bre composites (NFC) - Part 5: Specifications for cladding profiles and tiles Composites base de matires cellulosiques et de thermoplastiques (communment appels composites bois-polymres (WPC) ou composites fibres dorigine naturelle (NFC) - Partie 5: Spcifications relatives aux lames et plaques pour

7、bardage et lambris Verbundwerkstoffe aus cellulosehaltigen Materialien und Thermoplasten (blicherweise Holz-Polymer-Werkstoffe (WPC) oder Naturfaserverbundwerkstoffe (NFC) genannt) -Teil 5: Anforderungen an Profile und Formteile fr Wandbekleidungen This European Standard was approved by CEN on 9 Nov

8、ember 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be o

9、btained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the

10、 CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Irel

11、and, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Cen

12、tre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15534-5:2014 EBS EN 15534-5:2014EN 15534-5:2014 (E) 2 Contents Page Foreword 3 1 Scope 5 2 Normative references 5 3 Terms and definitions .

13、5 4 Requirements .5 4.1 General 5 4.2 Material .6 4.3 Appearance 6 4.4 Physical characteristics 6 4.5 Mechanical characteristics .7 4.5.1 Falling mass impact resistance 7 4.5.2 Flexural properties.7 4.5.3 Durability of products against biological agents .7 4.5.4 Durability of the products against ag

14、eing and moisture .8 4.5.5 Thermal properties 9 4.5.6 Additional characteristics .9 5 Marking 10 Annex A (informative) Minimum frequencies of testing for factory production control purposes . 12 Bibliography . 13 BS EN 15534-5:2014EN 15534-5:2014 (E) 3 Foreword This document (EN 15534-5:2014) has be

15、en prepared by Technical Committee CEN/TC 249 “Plastics”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2014, and conflicting national standards sha

16、ll be withdrawn at the latest by July 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document together with EN 15534-4:201

17、4 supersedes CEN/TS 15534-3:2007. The significant changes that have been made since the previous edition are the following: splitting into Parts 4 and 5 of CEN/TS 15534-3:2007; change of the status from Technical Specification to European Standard; complete technical review of the document; change o

18、f the scope from characterization to specification of the products. EN 15534 consists of the following parts: EN 15534-1, Composites made from cellulose-based materials and thermoplastics (usually called wood-polymer composites (WPC) or natural fibre composites (NFC) Part 1: Test methods for charact

19、erization of compounds and products prEN 15534-2, Composites made from cellulose-based materials and thermoplastics (usually called wood-polymer composites (WPC) or natural fibre composites (NFC) Part 2: Characterization of compounds1) EN 15534-4, Composites made from cellulose-based materials and t

20、hermoplastics (usually called wood-polymer composites (WPC) or natural fibre composites (NFC) Part 4: Specifications for decking profiles and tiles EN 15534-5, Composites made from cellulose-based materials and thermoplastics (usually called wood-polymer composites (WPC) or natural fibre composites

21、(NFC) Part 5: Specifications for cladding profiles and tiles prEN 15534-6, Composites made from cellulose-based materials and thermoplastics (usually called wood-polymer composites (WPC) or natural fibre composites (NFC) Part 6: Specifications for fencing profiles and systems1) prEN 15534-7, Composi

22、tes made from cellulose-based materials and thermoplastics (usually called wood-polymer composites (WPC) or natural fibre composites (NFC) Part 7: Specifications for general purpose profiles in external applications1)1) In preparation. BS EN 15534-5:2014EN 15534-5:2014 (E) 4 According to the CEN-CEN

23、ELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, I

24、celand, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 15534-5:2014EN 15534-5:2014 (E) 5 1 Scope This European Standard specifies the characteristics of claddin

25、g profiles and tiles made from cellulose-based materials and thermoplastics, usually called wood-polymer composites (WPC) or natural fibre composites (NFC), for external or internal use. This part of EN 15534 is applicable to extruded profiles but also to tiles manufactured by other plastics process

26、ing techniques, e.g. injection moulding. It is not applicable to support rail profiles, cover strip profiles and fastener devices which are out of the scope of this part of EN 15534. EN 15534-1 specifies the test methods relevant to this part of EN 15534. NOTE For editorial reasons, in EN 15534 the

27、abbreviation “WPC” is used for “composites made from cellulose-based materials and thermoplastics”. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited

28、 applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 927-6, Paints and varnishes Coating materials and coating systems for exterior wood Part 6: Exposure of wood coatings to artificial weathering using fluorescent UV lamps and water E

29、N 15534-1:2014, Composites made from cellulose-based materials and thermoplastics (usually called wood-polymer composites (WPC) or natural fibre composites (NFC) Part 1: Test methods for characterization of compounds and products EN 16472, Plastics Method for artificial accelerated photoageing using

30、 medium pressure mercury vapour lamps EN ISO 4892-2, Plastics Methods of exposure to laboratory light sources Part 2: Xenon-arc lamps (ISO 4892-2) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 15534-1:2014 apply. 4 Requirements 4.1 General Initial t

31、ype testing shall be performed to demonstrate compliance with the requirements specified in Clause 4 of this part of EN 15534. The tests according to 4.5.6 shall be carried out if the performance is declared by the manufacturer. Initial type testing shall be repeated, whenever a change occurs in the

32、 composition of the product, its geometry or in the production process. In case of a minor change, only the properties which could be influenced by this change shall be tested. NOTE Minimum frequencies of testing for factory production control purposes are given in Annex A. BS EN 15534-5:2014EN 1553

33、4-5:2014 (E) 6 4.2 Material The base polymer, from which the material is produced, and the type and content of cellulose-based material shall be declared by the manufacturer. Reprocessable and/or recyclable materials may be used for manufacturing the components provided that they satisfy to the prov

34、isions of this part of EN 15534. WPC materials are recyclable materials which can be treated in a material recovery process intended to save resources while minimizing harmful emissions into air, water and soil as well as their impacts on human health. NOTE A scheme for the characterization of plast

35、ics waste is given in EN 15347 2 and guidelines for the recovery and recycling are given in ISO 15270 3. 4.3 Appearance For production control purposes, the manufacturer shall compare three samples drawn at random from the same profile/tile production batch with a control sample, under the illuminat

36、ion conditions defined in EN 15534-1:2014, 6.1. The control samples shall be stored in a dark room and renewed every six months. If a control sample is put in contact with water, it shall be renewed immediately. 4.4 Physical characteristics When tested in accordance with the test methods as specifie

37、d in Table 1, using the parameters indicated, the profiles/tiles, as delivered to the customer, shall have characteristics conforming to the requirements given in Table 1. Table 1 Physical characteristics Characteristic Requirements Test method Number of test specimens Linear mass (applicable to pro

38、files) Individual values 95 % declared value by the manufacturer. The linear mass and tolerances shall be declared by the manufacturer. EN 155341:2014, 6.5 3 specimens Thickness, width and length (applicable to profiles) The relevant dimensional values and their tolerances shall be declared by the m

39、anufacturer. EN 155341:2014, 6.6.2 3 specimens Deviation from straightness (applicable to profiles) The deviation of straightness and its tolerance shall be declared by the manufacturer. EN 155341:2014, 6.6.3 3 specimens Cupping The cupping value and its tolerance shall be declared by the manufactur

40、er. EN 155341:2014, 6.6.4 3 specimens BS EN 15534-5:2014EN 15534-5:2014 (E) 7 4.5 Mechanical characteristics 4.5.1 Falling mass impact resistance When tested in accordance with the test methods as specified in Table 2, using the parameters indicated, the profiles/tiles, as delivered to the customer,

41、 shall have characteristics conforming to the requirements given in Table 2. Table 2 Falling mass impact resistance Requirements Test parameters Test method Number of test specimens Non-cellular material profiles No more than 1 test specimen out of 10 test specimens shall show a failure. H: (1 000 5

42、) mm Ms: (500 2) g EN 155341:2014, 7.1.2.2.1 10 specimens/face Cellular material profiles No more than 1 test specimen out of 10 test specimens shall show a failure. H: (1 000 5) mm Ms: (500 2) g EN 155341:2014, 7.1.2.2.2 10 specimens/face 4.5.2 Flexural properties When tested in accordance with the

43、 test method as specified in Table 3, using the parameters indicated, the profiles/tiles, as delivered to the customer, shall have characteristics conforming to the requirements given in Table 3. Table 3 Flexural properties Requirement Test parameters Test method Number of test specimens - Deflectio

44、n under a load of 250 N 5,0 mm (arithmetic mean value) - Bending strength Span in use declared by the manufacturer EN 155341:2014, Annex A 4 specimens/side 4.5.3 Durability of products against biological agents For the purpose of this part of EN 15534, use classes according to the environmental cond

45、itions are defined in Table 4. Table 4 Use class and occurrence of biological agents Use class Service situation Biological agents 2 Internal use or covered location None 3 External use, above ground Basidiomycetes NOTE Use classes 2 and 3 are derived from EN 335:2013, Table 1. If products of differ

46、ent geometries are made from the same material, only one product shall be tested. When tested in accordance with the test methods as specified in Table 5, using the parameters indicated, the products shall have characteristics conforming to the requirements given in Table 5. BS EN 15534-5:2014EN 155

47、34-5:2014 (E) 8 Table 5 Resistance against biological agents Characteristics Requirements Test method Number of test specimens Resistance against basidiomycetes The test result shall be declared. EN 155341:2014, 8.5.2 See EN 155341:2014, Table 3 NOTE At the date of publication of this part of EN 155

48、34, there is a lack of experience to specify a requirement for this property. 4.5.4 Durability of the products against ageing and moisture When tested in accordance with the test methods as specified in Table 6, using the parameters indicated, the products, as delivered to the customer, shall have c

49、haracteristics conforming to the requirements given in Table 6. Table 6 Durability of the products against ageing and moisture Properties Requirements Test parameters Test method Number of test specimens Resistance to artificial weathering (use class 3, only) - L*, a*, b* shall be declared - Appearance criteria, as defined by the manufacturer 300 h EN ISO 4892-2 2 016 h EN 927-6 750 h EN 16472“ EN 155341:2014, 8.1 1 specimen/colour (5 measurements /specimen) Moisture resistance