EN 643-2001 en Paper and Board - European List of Standard Grades of Recovered Paper and Board《纸和板 回收纸和板的欧洲标准等级表》.pdf

《EN 643-2001 en Paper and Board - European List of Standard Grades of Recovered Paper and Board《纸和板 回收纸和板的欧洲标准等级表》.pdf》由会员分享，可在线阅读，更多相关《EN 643-2001 en Paper and Board - European List of Standard Grades of Recovered Paper and Board《纸和板 回收纸和板的欧洲标准等级表》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 643:2014Paper and board Europeanlist of standard grades of paperand board for recyclingBS EN 643:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 643:2014. Itsupersedes BS EN 643:2002 which is withdrawn.The UK participation in

2、its preparation was entrusted to TechnicalCommittee PAI/11, Methods of test for paper, board and pulps.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are re

3、sponsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 79419 3ICS 85.060Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards

4、Policy and Strategy Committee on 31 January 2014.Amendments issued since publicationDate Text affectedBS EN 643:2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 643 January 2014 ICS 85.060 Supersedes EN 643:2001English Version Paper and board - European list of standard grades of paper and b

5、oard for recycling Papiers et cartons - Liste europenne des sortes standard de papiers et cartons pour recyclage Papier, Karton und Pappe - Europische Liste der Altpapier-Standardsorten This European Standard was approved by CEN on 6 December 2013. CEN members are bound to comply with the CEN/CENELE

6、C Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or

7、to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the offic

8、ial versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,

9、Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of e

10、xploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 643:2014 EBS EN 643:2014EN 643:2014 (E) 2 Contents Page Foreword 3 Introduction .4 1 Scope 5 2 Terms and definitions .5 3 Group classification 6 4 Grade identification .6 5 General requirements 7 5.1 So

11、urce of the paper and board for recycling 7 5.2 Prohibited materials 7 5.3 Unwanted materials .7 5.4 Moisture content in paper and board for recycling 7 5.5 Form of delivery .7 5.6 Additional requirements for grades intended for deinking .8 5.6.1 Introduction 8 5.6.2 Age of newspapers 8 5.6.3 Paper

12、products suitable for deinking 8 6 Classifications 8 6.1 Group 1, ordinary grades 8 6.2 Group 2, medium grades 9 6.3 Group 3, high grades 11 6.4 Group 4, kraft grades . 13 6.5 Group 5, special grades . 14 Bibliography . 16 BS EN 643:2014EN 643:2014 (E) 3 Foreword This document (EN 643:2014) has been

13、 prepared by Technical Committee CEN/TC 172 “Pulp, paper and board”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2014 and conflicting national sta

14、ndards shall be withdrawn at the latest by July 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 643:

15、2001. With regard to EN 643:2001, the following changes have been made: a) due to fundamental changes in waste legislation, the classification of grades has to be adapted (see introduction); b) the terminology has been modified to be in accordance with the use of the product for paper recycling; c)

16、introduction in the classification tables of two new columns, one specifying the limits for non-paper components, and one specifying the limits of unwanted material; d) addition of “Bibliography”; e) editorial updating. According to the CEN/CENELEC Internal Regulations, the national standards organi

17、sations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, M

18、alta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 643:2014EN 643:2014 (E) 4 Introduction This document, the European list of standard grades of paper and board for recycling, is intended to be used by industry p

19、rofessionals, organisations and individuals with an interest in the paper-recycling sector. It is intended to assist them in the buying and selling of these raw materials, which are intended for recycling by the paper and board industry without the need of additional sorting prior to use at a paper

20、mill. The definition for prohibited materials and the limits for non-paper components provide guidance and support for Customs and Excise Officers who are required to differentiate these raw materials from waste in the context of supranational legislation on the control of waste shipments. Furthermo

21、re, it is recommended that this document is used at all national levels in all official reports and in the day-to-day operation of companies. It secures the quality of the supply of paper and board for recycling to the paper mills through responsible sourcing of the paper industrys raw materials. Th

22、e major criterion is the use of the product for paper recycling. To take account of this criterion, the English terminology of EN 643 has been amended by substituting the term “Recovered paper and board” by “Paper and board for recycling” in the title and throughout the document. The revision of EN

23、643 coincides with a fundamental change in waste legislation. The Waste Framework Directive (Directive 2008/98/EC 5) introduces a procedure for defining End-of-Waste (EoW) criteria, which a given waste stream need to fulfil in order to cease to be waste. The End-of-Waste criteria require compliance

24、with EN 643, the provision of information on material that has ceased to be waste and the implementation of a quality management system. It should be pointed out that the code numbers used to denote specific grades are not consecutive, as some grades have lost their importance in recent years. This

25、affects grades 1.08, 1.10, 2.09 and 3.07. Wherever possible, the classification of grades was not changed compared to the previous version of this standard. Finally, a limit for non-paper components is set for every grade, typically below 1,5 %, weight by weight. Much effort was given to the definit

26、ion of tolerance levels for non-paper components and unwanted materials. The definition of tolerance levels reduces the need for individual agreements between buyer and supplier. However, specific agreements between individual buyers and suppliers may be used. Higher tolerances lead to non-standard

27、grades. This document has been prepared and supported by the following European organisations: CEPI Confederation of European Paper Industries; ERPA European Recovered Paper Association; FEAD European Federation of Waste Management and Environmental Service. BS EN 643:2014EN 643:2014 (E) 5 1 Scope T

28、his European Standard defines grades of paper and board for recycling used as raw material for recycling in the manufacture of paper and board products in the paper industry. This European Standard also specifies tolerances for unwanted materials as well as the composition of paper and board for rec

29、ycling. Unusable materials (prohibited and unwanted materials) are clearly defined for all people involved in the management of paper and board for recycling. 2 Terms and definitions For the purposes of this document, the following terms and definitions apply. 2.1 paper and board for recycling natur

30、al fibre based paper and board suitable for recycling and consisting of paper and board in any shape, products made predominately from paper and board, which may include other constituents that cannot be removed by dry sorting, such as coatings and laminates, spiral bindings, etc. 2.2 prohibited mat

31、erials any materials which represent a hazard for health, safety and environment, such as medical waste, contaminated products of personal hygiene, hazardous waste, organic waste including foodstuffs, bitumen, toxic powders and similar 2.3 non-paper components any foreign matter in paper and board f

32、or recycling, which is not a constituent part of the product and can be separated by dry sorting, such as: metal; plastic; glass; textiles; wood; sand and building materials; synthetic materials Note 1 to entry: Non paper components are part of the total amount of unwanted materials (see.2.7). 2.4 p

33、aper and board detrimental to production those papers and boards which have been recovered or treated in such a way that they are, for a basic or standard level of equipment, unsuitable as raw material for the manufacture of new paper and board products, or are actually damaging, or whose presence m

34、akes the whole consignment of paper unusable Note 1 to entry: For grades intended for deinking, all paper containing brown, unbleached fibres are considered detrimental to production. BS EN 643:2014EN 643:2014 (E) 6 Note 2 to entry: Some mills have developed their technology to handle grades, which

35、are detrimental to production in standard processes; therefore, the range of paper and board capable of being recycled is increasing. 2.5 paper and board not according to grade definition paper and board or products thereof which are not included in the description of the specific grade of paper and

36、 board for recycling Note 1 to entry: This could lead to regrading. 2.6 paper products suitable for deinking suitability for deinking is a characteristic of a printed-paper product Note 1 to entry: For details on how to make this evaluation, see “Assessment of Print Product Recyclability Deinkabilit

37、y Score” 3. 2.7 unwanted material outthrows material not suitable for the production of paper and board Note 1 to entry: The unwanted material may comprise: non-paper components; paper and board detrimental to production; paper and board not according to grade definition; paper products not suitable

38、 for deinking (if applicable). 3 Group classification Paper and board for recycling is classified as follows: Group 1: Ordinary grades; Group 2: Medium grades; Group 3: High grades; Group 4: Kraft grades; Group 5: Special grades. 4 Grade identification Grades of paper and board for recycling have be

39、en systematically numbered according to a numerical code system as follows: BS EN 643:2014EN 643:2014 (E) 7 In case of the main grades, replace the code of the subgrade by “00”. 5 General requirements 5.1 Source of the paper and board for recycling Paper and board mills may ask for a declaration fro

40、m the supplier about the origin of the material, in relation to national regulations or standard requirements relating to paper and board for recycling. The use of the “European Recovered Paper Identification System” (2008) is recommended. Paper and board for recycling originating from multi-materia

41、l collection systems, containing only material of a valuable, recyclable nature, shall be specifically marked. It is not permissible to mix it unmarked with other paper and board for recycling. Paper sorted from refuse collections is not suitable for use in the paper industry. 5.2 Prohibited materia

42、ls Prohibited materials, as defined in 2.2 are not permitted at all. 5.3 Unwanted materials In principle, paper and board for recycling should be supplied free of unwanted materials. The list of grades, however, specifies levels of tolerance for non-paper components and the total unwanted materials

43、(outthrows). The total value of unwanted materials is the combined percentage of all unwanted materials defined in 2.7. 5.4 Moisture content in paper and board for recycling In principle, paper and board for recycling will be supplied with moisture of not more than the naturally occurring level. Whe

44、re the moisture content is higher than 10 % (of air-dried weight), the additional weight in excess of 10 % may be claimed back with the method of testing and sampling to be agreed between buyer and seller. 5.5 Form of delivery Shredding of paper and board for recycling should be avoided and thus be

45、limited to reasons where confidentiality is required. If shredding cannot be avoided, the pieces should be left as large as possible. BS EN 643:2014EN 643:2014 (E) 8 5.6 Additional requirements for grades intended for deinking 5.6.1 Introduction The following requirements apply only to paper and boa

46、rd intended for deinking, and do not apply if paper and board for recycling is used in other paper recycling processes. 5.6.2 Age of newspapers If paper and board for recycling is intended to be used in a deinking process, the average age of the newspapers shall not exceed six months from the date o

47、f issue. This refers to the grades 1.09.00, 1.11.00, 2.01.00 and 2.02.01. 5.6.3 Paper products suitable for deinking Grades intended for deinking should consist of paper products suitable for deinking. Paper products not suitable for deinking belong to unwanted material. At the current state of know

48、ledge, this refers to most flexographic printing, inkjet, liquid toners and to some UV cured prints. NOTE If paper and board for recycling is not suitable for deinking it is usable in other paper recycling processes. Grades usually intended for deinking are: 1.06.00, 1.06.01, 1.06.02, 1.07.00, 1.09.

49、00, 1.11.00, 2.01.00, 2.02.01, 2.03.00, 2.03.01, 2.04.00, 2.04.01, 2.05.00, 2.05.01, 2.06.00, 2.06.01, 2.07.00, 2.07.01, 2.08.00, 2.12.00, 2.13.00, 3.01.00, 3.02.00, 3.03.00, 3.03.01, 3.04.00, 3.05.00, 3.06.00, 3.08.00, 3.09.00, 3.10.00, 3.10.01, 3.11.00, 3.11.01, 3.12.00, 5.05.00, 5.05.01, 5.09.00, 5.10.00 and 5.10.01. 6 Classifications The 5 groups of standard grades for paper and board for recycling are detailed in the following 5 tables. 6.1 Group 1, ordinary grades Table 1 Group 1, ordinary grades Code Name Description