EN 1304-2013 en Clay roofing tiles and fittings - Product definitions and specifications《屋顶黏土瓦片和装配 产品定义和规格》.pdf

《EN 1304-2013 en Clay roofing tiles and fittings - Product definitions and specifications《屋顶黏土瓦片和装配 产品定义和规格》.pdf》由会员分享，可在线阅读，更多相关《EN 1304-2013 en Clay roofing tiles and fittings - Product definitions and specifications《屋顶黏土瓦片和装配 产品定义和规格》.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 1304:2013Clay roofing tiles and fittings Product definitions andspecificationsBS EN 1304:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementatio

2、n of EN 1304:2013. Itsupersedes BS EN 1304:2005 which is withdrawn.Only clay tiles and fittings tested for impermeability as described inEN 539-1:2005, Clause 6, and classified as Category 1 in 4.4.1.2 b) Testmethod 2 should be used in the UK.The UK participation in its preparation was entrusted to

3、TechnicalCommittee B/542/3, Clay roofing tiles.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standa

4、rds Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 79921 1ICS 01.040.91; 91.100.25Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 June 2

5、013.Amendments issued since publicationDate Text affectedBS EN 1304:2013EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1304 May 2013 ICS 01.040.91; 91.100.25 Supersedes EN 1304:2005English Version Clay roofing tiles and fittings - Product definitions and specifications Tuiles et accessoires en

6、 terre cuite - Dfinitions et spcifications des produits Dach- und Formziegel - Begriffe und ProduktspezifikationenThis European Standard was approved by CEN on 5 April 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Europ

7、ean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions

8、 (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Bel

9、gium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switz

10、erland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. R

11、ef. No. EN 1304:2013: EBS EN 1304:2013EN 1304:2013 (E) 2 Contents Page Foreword . 3 1 Scope 4 2 Normative references . 4 3 Terms and definitions 4 3.1 General . 4 3.2 General . 5 3.3 Definitions specific to tiles and fittings with sidelock and headlock and tiles with sidelock only . 6 3.3.1 General

12、. 6 3.4 Definitions specific to over and under tiles 7 3.5 Further definitions 7 4 Requirements . 10 4.1 Structural characteristics 10 4.2 Fixing 11 4.3 Geometric characteristics 11 4.3.1 General . 11 4.3.2 Regularity of shape 11 4.3.3 Camber . 12 4.3.4 Dimensions and dimensional tolerances 12 4.4 P

13、hysical and mechanical characteristics 14 4.4.1 Impermeability 14 4.4.2 Flexural strength 14 4.4.3 Frost resistance . 15 4.5 Fire performance 15 4.5.1 External fire performance 15 4.5.2 Reaction to fire performance . 16 4.6 Dangerous substances 16 5 Marking and labelling . 16 6 Evaluation of conform

14、ity 17 6.1 General . 17 6.2 Initial type testing . 17 6.3 Factory production control 17 6.4 Sampling . 18 6.4.1 Sampling of tiles 18 6.4.2 Sampling of fittings 18 Annex A (normative) Initial type testing and frequency of product tests for factory production control 19 Annex B (informative) Appearanc

15、e . 20 Annex C (informative) Level(s) of frost resistance and number of cycles applicable in different countries . 21 Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive . 22 Bibliography 30 BS EN 1304:2013EN 1304:2013 (E) 3 Fo

16、reword This document (EN 1304:2013) has been prepared by Technical Committee CEN/TC 128 “Roof covering products for discontinuous laying and products for wall cladding”, the secretariat of which is held by IBN. This European Standard shall be given the status of a national standard, either by public

17、ation of an identical text or by endorsement, at the latest by November 2013, and conflicting national standards shall be withdrawn at the latest by November 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC

18、 shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1304:2005. In comparison to the previous edition, the following clauses are changed: 4.4.3, 4.6, Annex C and Annex ZA. This document has been prepared under a mandate given to CEN by the Europea

19、n Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. This document is part of a package of standards on clay roofing tiles and fitting

20、s. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,

21、Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 1304:2013EN 1304:2013 (E) 4 1 Scope This European Standard specifies requireme

22、nts for clay roofing tiles and fittings for pitched roof coverings and wall cladding and lining. It applies to all tiles and fittings as defined in Clause 3. Clay roofing tiles and clay fittings which conform to this European Standard are suitable for use as roof coverings, vertical wall cladding an

23、d lining. This European Standard defines the minimum requirements for a product which if satisfactory at the time of delivery will ensure that the product is able to perform its function in relation to the performance levels declared for it, whilst subjected to the changes that occur in such materia

24、ls during normal conditions of use. The results obtained according to the European Standard apply to products at the time they are offered for sale. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its applicat

25、ion. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 538, Clay roofing tiles for discontinuous laying Flexural strength test EN 539-1:2005, Clay roofing tiles for discontinuous laying D

26、etermination of physical characteristics Part 1: Impermeability test EN 539-2:2013, Clay roofing tiles for discontinuous laying Determination of physical characteristics Part 2: Test for frost resistance EN 1024, Clay roofing tiles for discontinuous laying Determination of geometric characteristics

27、EN 13501-1, Fire classification of construction products and building elements Part 1: Classification using data from reaction to fire tests EN 13501-5, Fire classification of construction products and building elements Part 5: Classification using data from external fire exposure to roof tests 3 Te

28、rms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 General 3.1.1 clay roofing tiles products for discontinuous laying on pitched roofs, and for wall cladding, which are manufactured by shaping (extrusion and/or pressing), drying and firing of the pr

29、epared clay, with or without additives Note 1 to entry: All or part of their surface can be covered with an engobe or glaze. BS EN 1304:2013EN 1304:2013 (E) 5 The principal types of tile are: 3.1.1.1 special tiles tiles made to shapes that vary from tile to tile for aesthetic reasons, for example ha

30、nd-made tiles 3.1.1.2 tiles with sidelock and headlock tiles with one or more longitudinal and transverse interlocking device(s) 3.1.1.3 tiles with sidelock only tiles with a longitudinal interlocking device but no transverse one Note 1 to entry: They can be used to obtain variable headlaps. 3.1.1.4

31、 tiles with headlock only tiles with a transverse interlocking device but no longitudinal one 3.1.1.5 tiles with variable headlap tiles with sidelock and headlock where the design of the tiles allows them to be fixed at varying headlaps 3.1.1.6 tiles with variable sidelap tiles with sidelock and hea

32、dlock where the design allows variation in the amount of sidelap 3.1.1.7 plain tiles tiles usually with a flat surface that can be slightly cross cambered and/or longitudinally cambered and which have no interlocking system Note 1 to entry: These tiles are generally rectangular, but can have a speci

33、ally shaped tail (e.g. fish-scale tiles with a rounded or sharp front edge). 3.1.1.8 overlapping tiles tiles which have no side or headlock and are profiled in an “S“ shape 3.1.1.9 over and under tiles tiles with the shape of a gutter whose design makes it possible either to fix them with variable h

34、eadlaps or where their headlap is fixed due to the presence of lugs on the tiles Note 1 to entry: They are made with their edges either parallel or forming a cone. 3.2 General 3.2.1 clay roofing fittings products that are complementary to the tiles and have a technical function There are two types o

35、f fittings: BS EN 1304:2013EN 1304:2013 (E) 6 3.2.2.1 coordinated fittings fittings that are intended to align or dimensionally interlock with the tiles with which they are to be laid EXAMPLE interlocking verge tile, interlocking ventilation tile, tile-and-a-half, interlocking ridge tiles, interlock

36、ing or aligning hip tile, aligning valley tile, interlocking or aligning angle tiles 3.2.2.2 uncoordinated fittings fittings that are not required to align or interlock with the tile with which they are to be laid EXAMPLE ridge tiles, hip tile, valley tile, verge tile, angle tiles 3.3 Definitions sp

37、ecific to tiles and fittings with sidelock and headlock and tiles with sidelock only 3.3.1 General 3.3.1.1 interlock system designed for the assembly of two adjoining tiles or fittings and usually including one or more raised parts called “ribs“ and one or more concave parts called “grooves“ 3.3.1.2

38、 longitudinal interlock system allowing two tiles or fittings in the same horizontal course to be fitted together 3.3.1.3 transverse interlock system allowing two tiles or fittings from successive horizontal courses to be fitted together Note 1 to entry: Three examples of interlock are shown in Figu

39、re 1. The arrangement of ribs and grooves limits the extent of movement between the tiles and improves the resistance to the ingress of water. Figure 1 Examples of interlock 3.3.2 straight bond tiles and fittings tiles or coordinated fittings designed to be laid so that the longitudinal joints of su

40、ccessive courses are aligned BS EN 1304:2013EN 1304:2013 (E) 7 3.3.3 broken bond tiles and fittings tiles or coordinated fittings designed to be laid so that the longitudinal joints are shifted half a tile between successive courses Note 1 to entry: Certain types of tiles or coordinated fittings are

41、 designed to be laid either straight bonded or broken bonded. 3.3.4 flat interlocking tiles and fittings interlocking tiles or coordinating fittings whose visible surface has no rib separating the areas of water flow from the longitudinal interlocks and where the longitudinal interlocks lie below th

42、e areas of water flow (see Figure 2) Key 1 areas of water flow 2 interlock Figure 2 Cross section and diagram of principle 3.4 Definitions specific to over and under tiles 3.4.1 under tiles tiles designed to be laid with their concave side facing upward and resting on the roofing support Note 1 to e

43、ntry: Under tiles may have no nib, or one or more nibs for laying on battens. 3.4.2 over tiles tiles designed to be laid with their concave side facing downward and straddling two under tiles Note 1 to entry: In general, the same units are used as under tiles when laid with their concave side facing

44、 upward and over tiles when they are laid with their concave side facing downward. However, the profile of under tiles can differ from that of over tiles; they can have, for example, a flat base or a shape allowing for the seating of the product on its support. In the latter case, under tiles are eq

45、uipped with two lateral upright sides. 3.4.3 over and under tiles with lugs to fix the headlap over and under tiles with lugs to fix the longitudinal overlap 3.5 Further definitions 3.5.1 additive material added in small quantities to the clay mix so as to facilitate the manufacture of the tile or f

46、itting or to improve its characteristics BS EN 1304:2013EN 1304:2013 (E) 8 3.5.2 efflorescense crystalline deposit of soluble salts found on the surface of tiles or fittings due to water migrating from within the tiles or fittings and evaporating on the surface 3.5.3 Ceramic coating 3.5.3.1 glaze gl

47、ass-based fired coating, or the material used to obtain this effect 3.5.3.2 engobe permeable or impermeable clay-based fired coating or the material used to obtain this effect 3.5.4 treatments factory-applied hydrophilic or hydrophobic agents, which change the behaviour of the surface of the clay ro

48、ofing tiles or fittings when it is wetted by water 3.5.5 crack more or less regular crack not running throughout the entire thickness of the product 3.5.6 colour variation variation in tone within one colour or within different colours in one production batch Note 1 to entry: See also Annex B. 3.5.7

49、 surface features hollows, raised areas, spots or colours, etc. characterising an entire batch and produced specifically for aesthetic purposes (to imitate the appearance of old tiles, for example) Note 1 to entry: See also Annex B. 3.5.8 clay fold interruption of continuity affecting only the surface of the product, caused by the formation of a fold during pressing Note 1 to entry: See also Annex B. 3.5.9 Overlap dimensions 3.5.9.1 General 3.5.9.1.1 gauge length of the exposed part of the fixed tile or coordinated fitting, measured longitudinally Note 1 to e