EN 13027-2001 en Packaging - Light-Gauge Metal Packaging - Open-Top Round Cans Defined by Their Nominal Gross-Lidded Capacity《包装 轻型金属包装 由标称容量限定的敞口的园形容器》.pdf

《EN 13027-2001 en Packaging - Light-Gauge Metal Packaging - Open-Top Round Cans Defined by Their Nominal Gross-Lidded Capacity《包装 轻型金属包装 由标称容量限定的敞口的园形容器》.pdf》由会员分享，可在线阅读，更多相关《EN 13027-2001 en Packaging - Light-Gauge Metal Packaging - Open-Top Round Cans Defined by Their Nominal Gross-Lidded Capacity《包装 轻型金属包装 由标称容量限定的敞口的园形容器》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、STDmBSI BS EN 13027-ENGL 2001 1624669 0897719 200 m BRITISH STANDARD Packaging - Light-gauge metal packaging - Open-top round cans defined by their nominal gross-lidded capacity The European Standard EN 13027:2001 has the status of a British Standard ICs 55.120 NO COPYING WITHOUT BSI PERMISSION EXCE

2、PT AS PERMITTED BY COPYRIGHT LAW BS EN 13027:2001 STDOBSI BS EN L3027-ENGL 2001 m Lb24bb9 0897720 T22 m BS EN 13027:2001 Amd. No. Date This British Standard, having been prepared under the direction of the Consumer Products and Services Sector Committee, was published under the authority of the Stan

3、dards Committee and comes into effect on 16 March 2001 Comments 8 BSI 03-2001 National foreword This British Standard is the official English language version of EN 13027:2001. The UK participation in its preparation was entrusted by Technical Committee PKW/5, Primary and transport packaging, to Sub

4、committee PKW/5/22, Metal packaging, which has the responsibility to: - - aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European d

5、evelopments and promulgate them in the UK. - A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standa

6、rds Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible fo

7、r their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 8, an inside back cover and a back cover. The BSI copyright date dis

8、played in this document indicates when the document was last issued. ISBN O 580 36937 4 STD*BSI BS EN 33027-ENGL 2001 Lb24bb9 0697723 969 E EUROPEAN STANDARD EN 13027 NORME EUROPENNE EUROPISCHE NORM January 2001 ICs 55.120 English version Packaging - Light-gauge metal packaging - Open-top round cans

9、 defined by their nominal gross-lidded capacity Emballage - Emballages mtalliques lgers - Boites rondes serties dfinies par leur capacit nominale totale Verpackungen - Feinstblechverpackungen - Falzdeckeldosen, gekennzeichnet durch deren Gesamtfassungsvermgen This European Standard was approved by C

10、EN on i December 2000. CEN members are bound to comply with the CENICENELEC Intemal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standard

11、s may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the M

12、anagement Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingd

13、om. EUROPEAN COMMVTEE FOR STANDARDIZATION EUROPISCHES KOMITEE FOR NORMUNG CO MIT EUROPBEN DE NORMALISATION Management Centre: rue de Stassart, 36 8-1050 Brussels Q 2001 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13027:2001 E S

14、TD-BSI BS EN L3027-ENGL 2OOL lb24bb9 0897722 8T5 Page 2 EN 13027:2001 Contents Page Foreword 3 Introduction . 4 1 Scope 5 2 Normative references 5 3 Dimensions . 5 Annex A (informative) Recommended diameters in relation to their nominal gross-lidded capacities . 7 Bibliography 8 STD-BSI BS EN 13027-

15、ENGL 2001 m Lb24bb9 0897723 731 Page 3 EN 13027:2001 Foreword This European Standard has been prepared by Technical Committee CEN/TC 261 “Packaging“, the secretariat of which is held by AFNOR This European Standard shall be given the status of a national standard, either by publication of an identic

16、al text or by endorsement, at the latest by July 2001, and conflicting national standards shall be withdrawn at the latest by July 2001. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Au

17、stria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. STD*BSI BS EN 13027-ENGL 2001 1b24bb9 0897724 678 = Page 4 EN 13027:2001 Introduction Efficient packaging

18、is of great importance for the distribution and the protection of goods. Insufficient or inappropriate packaging can lead to damage or wastage of the contents of the pack. It is based upon IS0 10653 : 1993. Recommended diameters related to this range of capacities are shown in the Annex A (informati

19、ve) to this standard. STD*BSI BS EN L3027-ENGL 2OOL = 1624bh9 CI897725 504 W Page 5 EN 13027:2001 1 Scope This European Standard specifies the range of the capacities of the cans defined by their nominal gross-lidded capacities, their metal thickness not exceeding 0,49 mm. Light-gauge open-top metal

20、 containers for liquid products with added gas defined by their nominal filling volumes are the subject of an other European standard. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at

21、 the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of

22、the publication referred to applies (including amendments). EN IS0 90-1 1999 Light gauge metal containers - Definitions and determination of dimensions and capacities - Open-top cans (IS0 90-1:1997) 3 Dimensions Standardised nominal gross-lidded capacities are listed in table 1. The Annex A of this

23、standard includes the nominal diameters linked to these capacities, these diameters being strongly recommended at European level. Within this same Annex A, are listed provisional additional nominal diameters; it is understood that these additional diameters will be reviewed, 5 years after the public

24、ation of this standard, to decide if they have to remain in this annex or to be deleted taking into account their importance in the market at this time. The tolerances for nominal gross-lidded capacities are defined in EN IS0 90-1 :1999. Page 6 EN 13027:2001 636 720 850 1062 Table 1 - List of capaci

25、ties of open-top round cans defined by their nominal gross-lidded capacity Nominal gross-lidded Capacity 85 106 1 25 1 42 1 70 1 98 21 2 31 4 403 425 I 446 I 492 I 580 I I 1275 I I 1700 I 1800 2650 31 O0 4250 10200 STD.BSI BS EN 13027-ENGL 2OOL D 1624667 0897727 387 1800 2650 31 O0 4250 Page 7 EN 13

26、027:2001 99 153 Annex A (i nf or mat ive) 10200 Recommended diameters in relation to their nominal gross-lidded capacities 230 Recommended diameters in relation to their nominal gross-lidded capacities should be as shown in table A.l. Table A.l - Recommended diameters in relation to their nominal gr

27、oss-lidded capacities Page 8 EN 13027:2001 Bibliography IS0 10653 IS0 1361 1993 Light-gauge metal containers - Round open-top cans - Cans defined by their nominal gross lidded capacities Light-gauge metal containers - Round open-top cans - Internal diameters BS EN 13027:2001 BSI 389 Chiswick High Ro

28、ad London w4 4AL4 STD*BSI BS EN 13027-ENGL 2001 lb24bb9 0877729 IST M BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Chart

29、er. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccura

30、cy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that

31、subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website at httr,:/www.

32、bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international sta

33、ndards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up t

34、o date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is available on the BSI website at httr,:/www.bsi-

35、. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transm

36、itted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. “his does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. if permission is granted, the terms may include royalty payments or a licensing sgreement. Details and advice can be obtained from the Copyright Manager. Fel: 020 8996 7070.