EN 12316-1-1999 en Flexible Sheets for Waterproofing - Determination of Peel Resistance of Joints - Part 1 Bitumen Sheets for Roof Waterproofing《防水韧性板 接头抗剥离性的测定 第1部分 屋顶防水沥青板》.pdf

《EN 12316-1-1999 en Flexible Sheets for Waterproofing - Determination of Peel Resistance of Joints - Part 1 Bitumen Sheets for Roof Waterproofing《防水韧性板 接头抗剥离性的测定 第1部分 屋顶防水沥青板》.pdf》由会员分享，可在线阅读，更多相关《EN 12316-1-1999 en Flexible Sheets for Waterproofing - Determination of Peel Resistance of Joints - Part 1 Bitumen Sheets for Roof Waterproofing《防水韧性板 接头抗剥离性的测定 第1部分 屋顶防水沥青板》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 STD.BS1 BS EN 1231b-1-ENGL 2000 6 1b24bb 0838215 54E BRITISH STANDARD Flexible sheets for waterproofing - Determination of peel resistance of joints - Part 1: Bitumen sheets for roof waterproofing The European Stanch British Sandard ET 2316 1999 has the status of a ICs 91.100.60 NO COPYING WITHOW B

2、SI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW I kS EN .2316-1:2OOO * STDmBSI BS EN L23Lh-L-ENGL 2000 LhS4bb9 08382Lh 485 9 BS EN 12316-1:2000 Amd. No. National foreword Date Comments This British Standard is the official English language version of EN 123161: 1999. The UK participation in its p

3、reparation was entrusted by Technical Committee BM6, Flexible sheets for waterproofing, to Subcommittee B/Wl, Bitumen sheets, which has the responsibility to: - aid enquirers to understand the text; - present to the responsible European committee any enquiries on the - monitor related internationai

4、and European developments and promulgate intepretaton, or proposals for change, and keep the UK interests informed them in the TJK A list of organizations represented on this subcommittee can be obtained on request to its secrem. Cross-references The British Standards which implement international o

5、r European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “Intemational Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include ali the

6、 necessary provisions of a contract. Users of British standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title pag

7、e, pages 2 to 7, and a back cover. The BSI copynght notice displayed in this document indicates when the document waslastissued. This British Standard, having been prepared under the direction of the Sector Committee Builduig and Civil Engineering, was published under the authority of the Standards

8、Conunime and comes into effect on 15 March 2 ISBN O 680 36138 4 STD-BSI BS EN 123Lb-1-ENGL 2000 1b24bb9 0838217 311 m EUROPEAN STANDARD NORME EUROPEENNE EUROPISCHE NORM EN 12316-1 September 1999 _ ICs 91.100.50 English version Flexible sheets for waterproofing - Determination of peel resistance of j

9、oints - Part 1 : Bitumen sheets for roof waterproofing Feuilles souples dtanchit - Dtermination de la rsistance au pelage des joints - Partie 1: Feuilles dtanchit de toiture bitumineuses Abdichtungsbahnen - Bestimmung des Schalwiderstandes der Fgenhte - Teil 1: Bitumenbahnen fr Dachabdichtungen This

10、 European Standard was approved by CEN on 13 August 1999. CEN members are bound to comply with the CENICENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical referenc

11、es concerning sich national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by tmslation under the responsibility of a CEN member into it

12、s own language and notified to the Central Secretariat has the same status as tie official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain

13、, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Central Secretariat: rue de Stassari, 36 8-1050 Brussels Q 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN nation

14、al Members. Ref. No. EN 12316-1:1999 E - STD-BSI BS EN 3231b-l1-ENGL 2000 1624bb9 0838218 258 Page 2 EN 12316-1:1999 i Contents Page Foreword Introduction 1 Scope 2 Nonnative references 3 Definitions 4 Principle 5 Apparatus 6 7 Preparation test specimens 8 Procedure 9 10 Test report Sampling and pre

15、paration of joint test pieces Expression of results, evaluation and precision of test method 3 3 3 3 3 4 4 4 4 6 6 7 O BSI 03-2000 STD-BSI BS EN 123Lb-1-ENGL 2000 H 1b24bb OB38219 194 H Page 3 EN 12316-1:1999 Foreword This European Standard has been prepared by Technical Committee CENTTC 254, Flexib

16、le sheets for waterproofing, the Secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2000, and conflicting national standards shall be withdrawn at the lates

17、t by March 2000. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherla

18、nds, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Introduction This European Standard is intended for the characterization of bitumen sheets as manufactured or supplied before use. The test method relates exclusively to products, or to their components where appropriate, and

19、not to waterproofing membrane systems composed of such products and installed in the works. This test is intended to be used in conjunction with European Standards on product specifications for reinforced and unreinforced bitumen sheets for roofing. 1 Scope This European Standard specifies a test me

20、thod for determining the resistance to peeling of joints between two adjacent sheets of the same bitumen-based roofing sheets. This test method is intended to be used for testing the joints in mechanically fastened single layer bitumen roofing. The peeling characteristics of a joint between two widt

21、hs of bitumen-based sheets vary considerably depending on the material, on the method of jointing (flame or heat welding, hot adhesive or bitumen, cold adhesive, etc.) the size of the overlap and the workmanship. 2 Normative references This European Standard incorporates by dated or undated referenc

22、e, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated

23、 in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 10002 - 2, Tensile testing of metallic materials - Part 2: Verification for the force measuring system of the tensile testirg machine. 3 Definitions For the purpose of this standard,

24、 the definitions indicated in 3.1 and the corresponding European Standard on product specifications appiy. 3.1 peel resistance the tensile force required to completely separate a prepared joint test specimen by peeling Q BSI 03-2000 Page 4 EN 12316-1:1999 4 Principle A test specimen of a joint is pu

25、lled at a constant speed until complete separation occurs. The tensile force is continuously recorded throughout the test. 5 Apparatus Tensile testing machine equipped with a continuous recording of force and corresponding distance, capable of maintaining uniform rate of grip separation as specified

26、 below. The tensile testing machine shall have a sufficient loading capacity (at least 2 O00 N) and a sufficient distance of grip separation, with a grip separation speed of (100 f IO) mmlmin. The width of grips shall be not less than 50 mm. The tensile testing machine shall be equipped with grips o

27、f a type which maintains or increases the gripping pressure as a function of the increase of the force applied to the test specimen. The test specimen should be held so that it does not slip n the grips more than 2 mm. To prevent slipping from the grips exceeding 2 mm it will be permitted to use coo

28、led grips The method of gripping shall not induce premature failure at or in the grips. The force measuring system shall meet at least class 2 in accordance with table 2 of EN 10002 - 2 (.e. i2 %). 6 Sampling and preparation of joint test pieces Samples shall be taken in accordance with the correspo

29、nding European Standard. Joint test pieces to be used for providing test specimens should be previously conditioned for at least 20 h at (23 f 2) “C and at a relative humidity between 30 % and 70 %. Test pieces of the sheet are joined by the method(s) to be used for installation with the unbonded ma

30、terial left on one side of the joint (see figure 1). Joint test pieces should be prepared representing all the ways of jointing. 7 Preparation test specimens From each of these joint test piece five rectangular test specimens (50 f 1) mm wide shall be cut, perpendicular to the joint. They shall have

31、 such a length that the ends of the specimen fill the clamps and that the complete overlap can be tested (see figure 1 and figure 2). Test specimens should be conditioned for at least 20 h before the test at (23 i 2) OC and at a relative humidity between 30 % and 70 %. When cold adhesives are used f

32、or jointing it may be necessary to increase the conditioning time according to the manufacturers information O BSI 03-2000 Page 5 EN 12316-1:1999 Dimensions in millimetres n w -width of joint Figure 1 Preparation of test specimen from specially made joint test pieces of side and end laps Dimmensions

33、 in millimetres T 1 -grip; w - width of joint Figure 2 Peel strength testing of side and end laps 6 BSI 03-2000 Page 6 EN 12316-1:1999 8 Procedure The test specimen shall be firmly held in the grips of the tensile testing machine, taking care that the longitudinal axis of fie test specimen, the axis

34、 of the tensile testing machine and the grips are correctly aligned. The clear distance between the grips shall be (100 f 5) mm. No preload shall be applied. The test shall be camed out at (23 i 2) OC with a constant speed of grip separation of (100 i 1 O) mrnlmin. The applied force, in N, shall be

35、recorded continuously until the test specimen separates. The mode of failure of the joint shall be noted. 9 Expression of results, evaluation and precision of test method 9.1 Evaluation A force distance record shall be drawn up for each test specimen. 9.1.1 Maximum peel resistance Record the maximum

36、 force as the maximum peel resistance of the specimen expressed in N per 50 mm. 9.1.2 Average peel resistance The first and last quarter of the recorded data shall not be included when calculating the average peel resistance in N per 50 mm of the specimen. The average peel resistance value is calcul

37、ated on the remaining section by considering I O equidistant values (see figure 3). f! 9 Maximum peel forca 7 1 x! O % Distance a - Points to be evaluated 3/4 i Flgure 3 Graph for calculating the peel reslstance (example) 8 BSI 03-2000 STD.BS1 BS EN L23Lb-1-ENGL 2000 W Lb24bb 0838223 bL5 Page 7 EN 1

38、2316-1:1999 NOTE: The purpose of the evaluation method specified here is to calculate an average peel resistance value which corresponds to the mean value of the forces acting on the test specimen at certain specified times during testing. This method also permits an evaluation to be carried out if

39、the graphs do not feature any distinctive peaks. This can occur when testing some bonded materials. It should be noted that the resuts can vary, depending on the direction in which the specimens are taken. 9.2 Calculations From the resuts for each set of five test specimens both the mean value of ma

40、ximum peel resistance and average peel resistance shall be calculated and rounded to the nearest 5 N. 9.3 Precision of the test method No information is available at this time. 10 Test report The test report shall include at least the following infomation: a) all details necessary to identify the pr

41、oduct tested; b) a reference to this European Standard (EN 1231 6-1 ) and any deviation from it; c) information of sampling in accordance with clause 6; d) details of preparation of the test specimens in accordance with clause 7 and a detailed description of the method of jointing; e) the test resul

42、ts in accordance with clause 9; f) the date of the test. Q BSI 03-2000 BS EN 123 16-1:ZOOO BSI 389 Chiswick High Road London w4 4AL BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and

43、 at the intemational level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. t is the constant ah of BSI to improve the ty of our products and servic

44、es. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel 020 8996 9ooo. Fax: O20 8996 7400. BSI offers members an indivi

45、dual updating service called PLUS which ensures that mbscribers automaically receive the latest editions of standards. Buying standards 3rders for all BSI, international and foreign standards publications should be xidresed to Customer Services. Tel: 020 8996 9001. Fax 020 8996 7001. in response to

46、orders for international standards, it is BSI policy to supply the BSI mplementation of those that have been published as British Standards, unless Aherwise requested nformation on standards BSI provides a wide range of information on national, European and intemationai tored in a retrieval system o

47、r transmitted in any form or by any means - elecbonic, )hotocopying, recording or otherwise - without prior written permission from BSI. his does not preclude the free use, in the course of implementing the standard, of iecessary details such as symbols, and size, type or grade designations. If these letails are to be used for any other purpose than implementation then the prior witten permission of BSI must be obtained. f permission is grantmi, the terms may include royalty payments or a licensing greement Details and advice can be obtained from the Copyright Manager. rel: 020 8996 7070.