EN 1217-1997 en Materials and Articles in Contact with Foodstuffs - Test Methods for Water Absorption of Ceramic Articles《与食品有关的材料和物品 陶瓷制品水吸收特性的试验方法》.pdf

《EN 1217-1997 en Materials and Articles in Contact with Foodstuffs - Test Methods for Water Absorption of Ceramic Articles《与食品有关的材料和物品 陶瓷制品水吸收特性的试验方法》.pdf》由会员分享，可在线阅读，更多相关《EN 1217-1997 en Materials and Articles in Contact with Foodstuffs - Test Methods for Water Absorption of Ceramic Articles《与食品有关的材料和物品 陶瓷制品水吸收特性的试验方法》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD Materials and articles in contact with foodstuffs - Test methods for water absorption of ceramic articles The European Standard EN 12171997 has the status of a British Standard ICs 67.250; 81.060.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHI LAW BS EN 1217:19

2、98 - STD-BSI BS EN L2L7-ENGL 1778 lb2Libb7 Ob72418 2b7 AmdNo. BS EN 1217:1998 Date Textafected I This British Standard, having been prepared under the direction of the sedor Board for Consumer Products and Services, was pubiished under the authority of the Standars Board and comes into effect on 16

3、Aprii 1998 O BSI 1998 National foreword This British Standard is the English language version of EN 12171997. The UK participation in its preparation was entrusted to Technicai Committee CWB, pabeware, which has the responsibility to: - aid enquirers to understand the tee - present to the responsibl

4、e European committee any enquiries on the inteqxetation, or proposais for change, and keep the UK interests informed; - monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secre

5、m. Cross-references The British Sandards which implement intemational or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “Intrnational Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Elect

6、ronic Catalogue. A British Standard does not purport to include aii the necessary provisions of a contract Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legai obligations. Summary of pages This doc

7、ument comprises a front cover, an inside front cover, the EN titie page, pages 2 to 6, an inside back cover and a back cover. Amendments issued since publication ISBN O 680 29529 X NORMI3 EUR0PEE“E EUROP the lower the water absorption, the higher the degree of vitrifcation. A high degree of vitrific

8、ation is necessary for certain categories of ceramic articles to achieve important performance characteristics. Water absorption is one of the properties used to characterize different types of ceramic articles. Any of the three test methods may be used, as appropriate, but method A is based on Euro

9、pean Community Regulation No 679/72, Customs classification of products to be died to porcelain: Vitreous china“ or Semi-vitreous china“ type, and is for use for such classification purposes. 1 scope This European Standard specifies test methods for the determination of the water absorption of ceram

10、ic articles. Three test methods are described - test method A, based on the increase in mass of test specimens after immersion in boiling water under defined conditions, which requires test specimens with not more than one glazed surface; - test method B, based on the same principle and general proc

11、edure as method A but with a longer period of immersion in boiling water; - test method C, based on the increase in mass of test specimens after a combination of evacuation of the test specimens to assist water penetration, followed by immersion in water and boiling; the test specimens may be glazed

12、 on both surfaces and are taken from different parts of a ceramic article to include possible inhomogeneities of the article. NOTE Values of very low water absorption should preferably be determined by test method C. 2 Definitions For the purposes of this standard, the following definitions apply 2.

13、1 water absorption quantity of water that can be absorbed by the body of a ceramic ware 2.2 body ceramic material shaped to constitute the ware, more or less vitrified, which is generally coated with glaze Page 3 EN 12171997 3 Principle The increase in mass is determined as a result of immersion in

14、water under controlled conditions and is expressed as a percentage of the mass of the dry test specimen. 4 Water 4.1 Disliued or de-ionize warn, for test methods A and B. 4.2 De-gassed distilled or b) for hollow-ware, take one test specimen from the top section and the second test specimen from the

15、base area of the sample. NOTE The test specimens obtained in this way may be unglazed, glazed on one major surface, or glazed on both major surfaces. 7 Procedures 7.1 Test methodA Dry the test specimens to constant mass in the oven (5.1.1) at 110 “C * 5 “C. NOTE As a guide, a 3 h period will suffice

16、 for test specimens obtained by breaking an article of tableware. If the test specimens are obtained by cutting an article of tableware using a saw (5.1.8) and are wet, then a longer drying time may he necessary. Place the test specimens in the desiccator (5.1.3) and allow them to cool to ambient te

17、mperature. Weigh each test specimen and record the final mass, ml, to the nearest 0,05 g. Immediately after weighing immerse the test specimens in distilled or deionized water (4.1). To avoid bumping during subsequent boiling ensure that the test specimens are not in contact with the bottom of the v

18、essel (5.1.4). Boil for 2 h f 5 min and then leave the test specimens to soak in the cooling water for a furilter period of not less thCui 24 h. Remove the test specimens from the water and wipe with a clean and slightly moist smooth cotton cloth (5.1.6) to remove surface water. Completely dry the g

19、lazed surface and dry any cavities or holes using a slim, slightly damp brush (5.1.7). Weigh each test specimen and record the masses after immersion, m2, to the nearest 0,05 g. 7.2 Test method B Cany out the test procedure as described for method A in 7.1, except that the period of immersion in boi

20、ling water is extended to 4 h f 10 min. Page 5 EN 1217:1997 7.3 Test method C Dry the test specimens to constant mass in the oven (6.2.1) at 110 “C 5 OC. Place the test specimens in the desiccator (5.2.2) and allow them to cool to ambient temperature. Weigh each test specimen and record the mass, mi

21、, to the nearest 0,Ol g. Place the dry test specimens on setter pins into a suitable vessel (6.2.4), reduce the pressure therein to 2,5 kPa * 1,5 kPa and maintain at this pressure for 60 min 5 min. Without admitting air, admit degassed distilled or degassed de-ionized water (4.2) at ambient temperat

22、ure to the vessel, una the test specimens are fully covered. Then admit air to the vessel, returning it to atmospheric pressure, and boil the water and test specimens for 60 min f 5 min. To avoid bumping during the boiling ensure that the test specimens remain fuily submerged but do not touch the bo

23、ttom of the vessel. Mow the test specimens to cool for not less than 24 h whilst remaining submerged in the boiled water. Remove the test specimens from the water and wipe them with a moistened smooth cotton cloth (5.2.8) such that glazed surfaces are completely dry and broken surfaces retain a thin

24、 film of moisture appearing as a sheen. Weigh each test specimen and record the masses after immersion, m2, to the nearest 0,Ol g. 8 Expression of results For each test specimen, calculate the water absorption as a percentage of the dry mass of the test specimen using the following equation: x 100%

25、rn2 - ml ml water absorption = where: ml m2 is the mass of the test specimen after drying to constant mass, in grams; is the mass of the test specimen after immersion, in grams. Calculate the arithmetic mean of the results obtained for all test specimens to the first decimal place. 9 ist report The

26、test report shall include the following details: a) a reference to this European Standard b) an identification of the article tested; c) the test method used, i.e. A, B or C; d) water absorption for each test specimen calculated in accordance with the equation given in clause 8 and the arithmetic me

27、an of the results obtained for the test specimens. O BSI 1998 STD-BSI BS EN LELT-ENGL 1778 W Lb2LibbS Ob72424 5b0 Page 6 EN l217:1997 Annex A (informative) Bibliography European Community Rewon No. 679/72 - Customs classcaCion of products to be died to pomehin: Vitreous chinu” m “Semi-vitreous chinu

28、” type. O BSI 1998 BS EN 1217:1998 BSI 389 Chiswick High Road London w4 4AL BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal

29、 Charter. Revisions British Stanhds are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful i anyone nding an inaccur

30、acy or ambwty while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel 0181 996 9OOO. Fax 0181 996 7400. BSI offers members an individual updating service called PLUS which ensures that subs

31、cribers automatidy receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 0181 996 7000. Fax: 0181 996 7001. In response to orders for international standards, it is BSI policy to

32、supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Vario

33、us BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel 0181 996 7111. Fax 0181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the pur

34、chase price of standards. For details of these and other benefits contact Membership A- on. Tel 0181 996 7002. Fax 0181 996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as

35、permitted under the Copyright, Designs and Patents Act 19% no extract may be reproduced, stored in a relxieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission hm BSI. This does not preclude the free use, in the c

36、ourse of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained If permission is granted, the terms may include royalty payments or a licensing agreement Details and advice can be obtained from the Copyright Manager. Tel 0181 996 7070.