DLA SMD-5962-03249 REV A-2012 MICROCIRCUIT LINEAR QUAD CURRENT FEEDBACK WIDEBAND VIDEO OPERATIONAL AMPLIFIER MONOLITHIC SILICON.pdf

《DLA SMD-5962-03249 REV A-2012 MICROCIRCUIT LINEAR QUAD CURRENT FEEDBACK WIDEBAND VIDEO OPERATIONAL AMPLIFIER MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-03249 REV A-2012 MICROCIRCUIT LINEAR QUAD CURRENT FEEDBACK WIDEBAND VIDEO OPERATIONAL AMPLIFIER MONOLITHIC SILICON.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update drawing as part of 5 year review. -jt 12-02-02 C. SAFFLE REV SHEET REV SHEET REV STATUS REV A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY RICK OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.lan

2、dandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY RAJESH PITHADIA APPROVED BY RAYMOND MONNIN MICROCIRCUIT, LINEAR, QUAD, CURRENT FEEDBACK, WIDEBAND VIDEO OPERATIONAL AMPLIFIER, MONOLITHIC SILIC

3、ON DRAWING APPROVAL DATE 04-02-25 AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-03249 SHEET 1 OF 9 DSCC FORM 2233 APR 97 5962-E148-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-03249 DLA LAND AND

4、 MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes

5、 are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 03249 01 Q C X Federal stock class designator RHA designator (see 1.2

6、.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device c

7、lass M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type. The device type identify the circuit function as follows: Device type Generic number Circuit function 01 LMH

8、6722 Quad, current feedback, wideband video operational amplifier 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-S

9、TD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package

10、style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line Z GDFP1-G14 14 Flat pack with gull wing leads 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking perm

11、itted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-03249 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage (VS) 6.75 V dc Common mode input voltage (VCM) . -V to +V Differential inp

12、ut voltage (VID) . 2.2 V Maximum power dissipation (PD) 1 W 2/ Lead temperature (soldering, 10 seconds) +300C Junction temperature (TJ) . +175C Storage temperature range . -65C TA +150C Thermal resistance, junction-to-case (JC): Case C 24C/W Case Z . 26C/W Thermal resistance, junction-to-ambient (JA

13、): Case C 130C/W (still air) 83C/W (500 linear feet per minute air flow) Case Z . 165C/W (still air) 110C/W (500 linear feet per minute air flow) 1.4 Recommended operating conditions. Supply voltage (VS) 5 V dc Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Gove

14、rnment specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICA

15、TION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard

16、Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. _ 1/ Absolute maximum rating are limits beyond which damage to the device may occur. Operating ratings are conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specificati

17、ons apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. 2/ The maximum power dissipation must be derated at elevated temperatures and is dictated by TJ(maximum junction temperature), JA(package junc

18、tion to ambient thermal resistance), and TA(ambient temperature). The maximum allowable power dissipation at any temperature is PDmaximum = (TJmaximum TA) / JAor the number given in 1.3 herein, whichever is lower. Provided by IHSNot for ResaleNo reproduction or networking permitted without license f

19、rom IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-03249 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing ta

20、kes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified h

21、erein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class

22、level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines.

23、The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance character

24、istics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defin

25、ed in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“

26、on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certifi

27、cation mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a

28、 QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of

29、 compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, ap

30、pendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for devi

31、ce class M. For device class M, notification to DLA Land and Maritime -VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

32、HS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-03249 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limi

33、ts 2/ Unit Min Max DC parameter section Input bias current (noninverting) +IIN1 01 -10 +10 A 2,3 -15 +15 Input bias current (inverting) -IIN1 01 -12 +12 A 2,3 -20 +20 Input offset voltage VIORS= 50 1 01 -6.0 +6.0 mV 2,3 -10.0 +10.0 Supply current (all channels) ISNo load 1,3 01 27 mA 2 28 Power supp

34、ly rejection ratio PSRR +VS= +4.5 V to +5.0 V, 1 01 53 dB -VS= -4.5 V to 5.0 V 2 50 3 55 AC parameter section Small signal bandwidth SSBW -3 dB bandwidth, VOUT25 MHz, VOUT 2.0 VPP4 01 0.2 dB Second harmonic distortion HD2 2 VPPat 20 MHz 4 01 -38 dBc Third harmonic distortion HD3 2 VPPat 20 MHz 4 01

35、-46 dBc 1/ Unless otherwise specified, VS= 5 V, load resistance (RL) = 100 , gain (AV) = +6, and feedback resistance (RF) = 500 . 2/ The algebraic convention, whereby the most negative value is a minimum and the most positive is a maximum, is used in this table. Negative current shall be defined as

36、conventional current flow out of a device terminal. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-03249 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 Device

37、type 01 Case outlines C Z Terminal number Terminal symbol 1 OUTPUT A OUTPUT A 2 -INPUT A -INPUT A 3 +INPUT A +INPUT A 4 +VS+VS5 +INPUT B +INPUT B 6 -INPUT B -INPUT B 7 OUTPUT B OUTPUT B 8 OUTPUT C OUTPUT C 9 -INPUT C -INPUT C 10 +INPUT C +INPUT C 11 -VS-VS12 +INPUT D +INPUT D 13 -INPUT D -INPUT D 14

38、 OUTPUT D OUTPUT D FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-03249 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 3.9 Veri

39、fication and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the opti

40、on of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 49 (see MIL-PRF-38535, appendix A). 4. VERIFICATION 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedu

41、res shall be in accordance with MIL-PRF-38535 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. For device class M, sampling and inspection procedures shall be in accordance with M

42、IL-PRF-38535, appendix A. 4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and shall be conducted on all devices prior to qualification and technology conformance inspection. For device class M, screening shall be in accordance with method 5004 of MIL-S

43、TD-883, and shall be conducted on all devices prior to quality conformance inspection. 4.2.1 Additional criteria for device class M. a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level c

44、ontrol and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and fina

45、l electrical test parameters shall be as specified in table II herein. 4.2.2 Additional criteria for device classes Q and V. a. The burn-in test duration, test condition and test temperature, or approved alternatives shall be as specified in the device manufacturers QM plan in accordance with MIL-PR

46、F-38535. The burn-in test circuit shall be maintained under document revision level control of the device manufacturers Technology Review Board (TRB) in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the i

47、nputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein. c. Additional screening for device class V beyond the requirements of device

48、class Q shall be as specified in MIL-PRF-38535, appendix B. 4.3 Qualification inspection for device classes Q and V. Qualification inspection for device classes Q and V shall be in accordance with MIL-PRF-38535. Inspections to be performed shall be those specified in MIL-PRF-38535 and herein for groups A, B, C, D, and E inspections (see 4.4.1 through 4.4.4). 4.4 Conformance inspection. Technology conformance inspection for classes Q and V shall be in accordance with MIL-PRF-38535 including groups A, B, C, D, and E inspections and as specified herein. Quality c