DLA MS27383 REV B-2003 ADAPTER ASSEMBLY FLARELESS 90 DEG ELBOW TUBE TO HOSE-WITH SWIVEL NUT《90度弯管到胶皮管旋转螺母承插适配器装配》.pdf

《DLA MS27383 REV B-2003 ADAPTER ASSEMBLY FLARELESS 90 DEG ELBOW TUBE TO HOSE-WITH SWIVEL NUT《90度弯管到胶皮管旋转螺母承插适配器装配》.pdf》由会员分享，可在线阅读，更多相关《DLA MS27383 REV B-2003 ADAPTER ASSEMBLY FLARELESS 90 DEG ELBOW TUBE TO HOSE-WITH SWIVEL NUT《90度弯管到胶皮管旋转螺母承插适配器装配》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 DETAIL SPECIFICATION SHEET ADAPTER ASSEMBLY, FLARELESS, 90 ELBOW, TUBE TO HOSE - WITH SWIVEL NUT This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification and M

2、IL-DTL-27272. NOTE: Dimension A is measured between the hose end of the socket and the free end of the MS8000 series seal insert at its centerline when the socket is assembled on the nipple subassembly. FIGURE 1. Adapter assembly illustration. AMSC N/A 1 of 3 FSC 4730 DISTRIBUTION STATEMENT A. Appro

3、ved for public release; distribution is unlimited. MS27383B 25 September 2003 SUPERSEDING MS27383A 30 June 1972 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27383B 2 REQUIREMENTS Intended use. This adapter is intended for use with hos

4、e conforming to MIL-DTL-27267. Dimensions. Dimensions are in inches. Material. PIN suffix C, corrosion-resistant steel. No PIN suffix. Combination of aluminum alloy and corrosion-resistant steel. See applicable specification sheet and MIL-DTL-25579 for material of other components identified in tabl

5、e I for their material requirements. Adapter assembly illustration. See figure 1. Identification of product. The PIN and the manufacturers PIN and Government Entity (CAGE) Code shall be marked on a removable tag securely attached to the adapter. The PIN for this assembly shall be as specified in tab

6、le I (e.g., MS27383-10C). Order of precedence. This specification takes precedence over the documents referenced herein. Unless otherwise specified, referenced documents shall be of the issue in effect on the date of solicitation. Flareless fitting, hose connector design. Use MIL-DTL-25579/1 for app

7、lication of NAS 1760 design TABLE I. Adapter assembly composition. PIN 1/ Elbow subassembly PIN Sleeve PIN Socket PIN A 2/ max MS27383 MS27388 MS27070 MS27069 -10C -10C -10C -10C 2.26 -10 -10 -12C -12C -12C -12C 2.76 -12 -12 -16C -16C -16C -16C 2.93 -16 -16 -20C -20C -20C -20C 3.45 -20 -20 -24C -24C

8、 -24C -24C 3.74 -24 -24 1/ If required, lockwire holes to be drilled in accordance with SAE AS1043 and suffix L added to the Part or Identifying Number (PIN) (e.g., MS273838-10CL). 2/ Dimension A is measured between the hose end of the socket and the free end of the MS8000 series seal insert at its

9、centerline when the socket is assembled on the nipple subassembly. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes to complete reformatting. Provided by IHSNot for ResaleNo reproduc

10、tion or networking permitted without license from IHS-,-,-MS27383B 3 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AV DLA - CC Navy - AS Air Force - 99 (Project 4730-0868-021) DLA - CC Review activities: Army - AR, AT, MI Navy - MC, SA, SH Air Force - 71 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-