DLA MS21106 REV B-2010 CLAMP LOOP CUSHIONED 1200 DEG F CRES TYPE IV CLASS B.pdf

《DLA MS21106 REV B-2010 CLAMP LOOP CUSHIONED 1200 DEG F CRES TYPE IV CLASS B.pdf》由会员分享，可在线阅读，更多相关《DLA MS21106 REV B-2010 CLAMP LOOP CUSHIONED 1200 DEG F CRES TYPE IV CLASS B.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A FSC 5340 MS21106B 20 MAY 2010 SUPERSEDING MS21106A 2 December 1970 DETAIL SPECIFICATION SHEET CLAMP, LOOP, CUSHIONED, 1200 DEG. F., CRES TYPE IV, CLASS B This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquirin

2、g the product described herein shall consist of this specification sheet and procurement specification, MIL-C-8603. ZPART NUMBER TO BELOCATED IN THISAREASSECTION A - A.204 THROUGHWR .375TGRREINFORCEDCORNEREXDAAFIGURE 1. Clamp INCH-POUND Inactive for new design after 16 June 1997 Provided by IHSNot f

3、or ResaleNo reproduction or networking permitted without license from IHS-,-,-MS21106B 2 TABLE I. Dash numbers and dimensions. PART NUMBER RIGID TUBE NOMINAL OD (REF) D .015 E .015 G R .016 RAD S +.016 -.000 T W .015 X .015 Z MAX MS21106-2 1/8 .125 .457 .062 +.016 -.000 .062 .062 .0320 .0035 .375 .1

4、88 .497 MS21106-3 3/16 .188 .498 MS21106-4 1/4 .250 .529MS21106-5 5/16 .313 .560 MS21106-6 3/8 .375 .592MS21106-7 7/16 .438 .623 MS21106-8 1/2 .500 .654MS21106-9 9/16 .563 .749 .109 .500 .218 .622 MS21106-10 5/8 .625 .780 MS21106-11 11/16 .688 .811 MS21106-12 3/4 .750 .842 MS21106-13 13/16 .813 .858

5、 MS21106-14 7/8 .875 .889 MS21106-15 15/16 .938 .920 MS21106-16 1 1.000 .951MS21106-17 1-1/16 1.063 .983 MS21106-18 1-1/8 1.125 1.030 .094 +.031 -.000 .125 .656 MS21106-19 1-3/16 1.188 1.061 MS21106-20 1-1/4 1.250 1.092 MS21106-21 1-5/16 1.313 1.124 MS21106-22 1-3/8 1.375 1.155 MS21106-23 1-7/16 143

6、8 1.186 MS21106-24 1-1/2 1.500 1.217 MS21106-25 1-9/16 1.563 1.259 MS21106-26 1-5/8 1.625 1.280 MS21106-27 1.688 1.312MS21106-28 1-3/4 1.750 1.342 MS21106-29 1.813 1.374MS21106-30 1-7/8 1.875 1.405 MS21106-31 1.938 1.444 .125 +.031 -.000 .040 .004 MS21106-32 2 2.000 1.475 MS21106-33 2.062 1.507MS211

7、06-34 2-1/8 2.125 1.538 MS21106-35 2.188 1.570MS21106-36 2-1/4 2.250 1.600 MS21106-37 2.312 1.631MS21106-38 2-3/8 2.375 1.663 MS21106-40 2-1/2 2.500 1.728 MS21106-42 2.625 1.788MS21106-43 2.688 1.820 MS21106-44 2-3/4 2.750 1.851 MS21106-45 2.812 1.882MS21106-46 2.875 1.913 MS21106-48 3 3.000 1.976MS

8、21106-50 3.125 2.038 MS21106-52 3-1/4 3.250 2.101 MS21106-54 3.375 2.163MS21106-56 3-1/2 3.500 2.226 MS21106-58 3.625 2.288MS21106-64 4 4.000 2.476 MS21106-66 4.125 2.538Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS21106B 3 NOTES. 1. Clamp band

9、- Corrosion resistant steel Type 321 in accordance with SAE AMS 5510, annealed. Cushion - Corrosion resistant steel Type 321 or 347 in accordance with SAE AMS 5510 or SAE AMS 5512. 2. Protective Treatment: Passivate in accordance with SAE AMS 2700. 3. Remove all burrs and sharp edges. 4. Dimensions

10、are in inches. Unless otherwise specified, tolerances decimals +.015. 5. Dimension “D” is applicable in closed position only 6. The MS part number, including dash number, and manufacturers identification, shall be marked on each clamp. 7. Clamps shall be furnished in the open position. 8. Method of

11、cushion attachment to band is optional. 9. Reinforced corner is mandatory. 10. For design feature purposes, this standard takes precedence over procurement documents referenced herein. 11. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect

12、to the previous issue due to the extent of the changes. Custodians: Preparing activity: Army - AV DLA IS Navy - AS Air Force 99 (Project 5340-2010-012) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-