DLA MS9035 REV C (1)-2005 BOLT-MACHINE STEEL 12 POINT HEAD HEAT RESISTANT STEEL 3125-24 NS《0 3125-24 NS型12点抗热钢锚杆机》.pdf

《DLA MS9035 REV C (1)-2005 BOLT-MACHINE STEEL 12 POINT HEAD HEAT RESISTANT STEEL 3125-24 NS《0 3125-24 NS型12点抗热钢锚杆机》.pdf》由会员分享，可在线阅读，更多相关《DLA MS9035 REV C (1)-2005 BOLT-MACHINE STEEL 12 POINT HEAD HEAT RESISTANT STEEL 3125-24 NS《0 3125-24 NS型12点抗热钢锚杆机》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 INCH-POUNDMS9035C W/AMENDMENT 1 21 June 2005 MILITARY SPECIFICATION SHEET BOLT-MACHINE, STEEL, 12 POINT HEAD, HEAT RESISTANT STEEL, .3125-24 NS Inactive for new design after 20 May 1998 This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The re

2、quirements for acquiring the product described herein shall consist of this specification sheet and SAE-AS7478. TABLE I. DASH NUMBERS AND DIMENSIONSDASH NO. L K +.000 -.060 APPROX WEIGHT LBS/100 DASH NO. L K +.000 -.060 APPROX WEIGHT LBS/100 DASH NO. L K +.000 -.060 APPROX WEIGHT LBS/100 -05 -06 -07

3、 -08 -09 -10 -11 -12 -13 -14 -15 -16 -17 -18 -19 -20 -21 -22 .562 .625 .688 .750 .812 .875 .938 1.000 1.062 1.125 1.188 1.250 1.312 1.375 1.438 1.500 1.562 1.625 1/ 1/ 1/ 1/ 1/ 1/ 1/ .125 .188 .250 .312 .375 .438 .500 .562 .625 .688 .750 2.21 2.28 2.39 2.51 2.62 2.73 2.85 2.96 3.07 3.19 3.30 3.41 3.

4、52 3.64 3.75 3.87 3.98 4.10 -23 -24 -25 -26 -27 -28 -29 -30 -31 -32 -33 -34 -35 -36 -37 -38 -39 -40 1.688 1.750 1.875 2.000 2.125 2.250 2.375 2.500 2.625 2.750 2.875 3.000 3.125 3.250 3.375 3.500 3.625 3.750 .812 .875 1.000 1.125 1.250 1.375 1.500 1.625 1.750 1.875 2.000 2.125 2.250 2.375 2.500 2.62

5、5 2.750 2.875 4.22 4.33 4.55 4.77 5.00 5.23 5.45 5.67 5.90 6.13 6.36 6.58 6.80 7.03 7.27 7.50 7.73 7.95 -41 -42 -43 -44 -45 -46 -47 -48 -49 -50 -51 -52 -53 -54 -55 -56 -57 -58 3.875 4.000 4.125 4.250 4.375 4.500 4.625 4.750 4.875 5.000 5.125 5.250 5.375 5.500 5.625 5.750 5.875 6.000 3.000 3.125 3.25

6、0 3.375 3.500 3.625 3.750 3.875 4.000 4.125 4.250 4.375 4.500 4.625 4.750 4.875 5.000 5.125 8.17 8.40 8.63 8.86 9.08 9.30 9.52 9.74 9.95 10.17 10.40 10.63 10.86 11.10 11.33 11.56 11.78 12.00 1/ THREAD TO HEAD. MAXIMUM TWO INCOMPLETE THREADS AMSC N/A FSC 5305 1 of 3 Provided by IHSNot for ResaleNo re

7、production or networking permitted without license from IHS-,-,-MS9035C W/AMENDMENT 1 2 REQUIREMENTS: 1. MATERIAL: HEAT RESISTANCE STEEL IN ACCORDANCE WITH AMS 5732. 2. THREADS: THREADS IN ACCORDANCE WITH MIL-S-7742. INCOMPLETE THREADS NOT TO ENTER FILLET. 3. DIMENSIONING AND TOLERANCING: DIMENSIONI

8、NG AND TOLERANCING SHALL BE IN ACCORDANCE WITH ASME Y14.5M. 4. SURFACE TEXTURE: SURFACE TEXTURE, UNLESS OTHERWISE SPECIFIED, SHALL BE 125 MICROINCHES EXCEPT UPSET HEAD IN ACCORDANCE WITH ASME B46.1 5. FLUORESCENT PENETRANT INSPECTION: FLUORESCENT PENETRANT INSPECTION SHALL BE IN ACCORDANCE WITH ASTM

9、 E1417. 6. TOLERANCE: UNLESS OTHERWISE SPECIFIED, TOLERANCES SHALL BE FOR LINEAR DIMENSIONS +.010, ANGULAR DIMENSION +5. 7. EDGES: BREAK SHARP EDGES .003-.015 UNLESS OTHERWISE SPECIFIED. 8. PART NUMBER: THE PART NUMBER SHALL CONSIST OF THE BASIC MS NUMBER FOLLOWED BY A DASH NUMBER FROM TABLE I. EXAM

10、PLE: MS9035- 05DASH NUMBER BASIC MS NUMBER MS9035-05 INDICATES - BOLT, MACHINE, 12 POINT HEAD, HEAT RESISTANT STEEL,.3125-24 NS, LENGTH .562. NOTES: 1. ALL DIMENSIONS ARE IN INCHES. 2. DO NOT USE UNASSIGNED PART NUMBERS. 3. IN THE EVENT OF A CONFLICT BETWEEN THE TEXT OF THIS STANDARD AND THE REFEREN

11、CES CITED HEREIN, THE TEXT OF THIS STANDARD SHALL TAKE PRECEDENCE. 4. THIS STANDARD WAS DEVELOPED COOPERATIVELY WITH THE SAE AEROSPACE PROPULSION DIVISION. 5. AS AND AMS ARE SAE PUBLICATIONS. 6. SUBJECT TERM (KEY WORD) LISTING . BOLT, MACHINE, 12 POINT HEAD, HEAT RESISTANT STEEL. Provided by IHSNot

12、for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9035C W/AMENDMENT 1 3 7. AMENDMENT NOTATIONS: THE MARGINS OF THIS SPECIFICATION ARE MARKED WITH VERTICAL LINES TO INDICATE WHERE MODIFICATIONS FROM THIS AMENDMENT WERE MADE. THIS WAS DONE AS A CONVENIENCE ONLY AND THE G

13、OVERNMENT ASSUMES NO LIABILITY WHATSOEVER FOR ANY INACCURACIES IN THESE NOTATIONS. BIDDERS AND CONTRACTORS ARE CAUTIONED TO EVALUTATE THE REQUIREMENTS OF THIS DOCUMENT BASED ON THE ENTIRE CONTENT IRRESPECTIVE OF THE MARGINAL NOTATIONS. Custodians: Preparing Activity: Navy AS DLA-IS Air Force 11 (Pro

14、ject 5305-2005-001) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil/Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-