DLA MIL-PRF-94 2 E (1)-2008 RESISTORS VARIABLE COMPOSITION STYLE RV5.pdf

《DLA MIL-PRF-94 2 E (1)-2008 RESISTORS VARIABLE COMPOSITION STYLE RV5.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-94 2 E (1)-2008 RESISTORS VARIABLE COMPOSITION STYLE RV5.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Comments, suggestions, or questions on this document should be addressed to Defense Supply Center, Columbus, ATTN: DSCC/VAT, Post Office Box 3990, Columbus, OH 43218 3990, or emailed to Resistordla.mil. Since contact information can change, you may want to verify the currency of this address informa

2、tion using the ASSIST Online database at http:/assist.daps.dla.mil. AMSC N/A FSC 5905 INCH-POUND MIL-PRF-94/2E w/Amendment 1 9 June 2008 SUPERSEDING MIL-PRF-94/2E 2 June 2006 PERFORMANCE SPECIFICATION SHEET RESISTORS, VARIABLE, COMPOSITION, STYLE RV5 This specification is approved for use by all Dep

3、artments and agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements for style RV5 composition, variable resistors. 1.2 Part or Identifying Number (PIN). Resistors covered by this specification are identified by a PIN which is in the following form. RV5

4、NAYSD251A Style Coded dash number The coded dash number is derived in accordance with MIL-PRF-94 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this

5、specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they

6、 are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation (se

7、e 6.2). DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-94 - Resistor, Variable, Composition, General Specification for. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Ave

8、nue, Building 4D, Philadelphia, PA 19111-5094). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-94/2E w/Amendment 1 22.3 Order of precedence. In event of a conflict between the text of this document and the references cited herein (except for

9、 related associated specifications, specification sheets, or MS sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 General. The requirements for acquirin

10、g the product described herein shall consist of this document and MIL-PRF-94. 3.2 Interface and physical dimensions. The resistors shall meet the interface and physical dimensions specified in figure 1. 3.3 Nominal total resistance and rated continuous working voltages. The nominal total resistance

11、and rated continuous working voltage (RCWV) shall be as specified in table I. TABLE I. Nominal total resistance and rated continuous working voltage. RCWV 1/ (volts) RCWV 1/ (volts) Nominal total resistance (in ohms) Taper A Tapers C and F Nominal total resistance (in megohms) Taper A Tapers C and F

12、 250 500 1,000 2,000 2,500 5,000 10,000 20,000 25,000 50,000 2/ 2/ 11 16 22 31 35 50 71 100 112 158 16 22 25 36 50 70 80 112 0.10 0.20 0.25 0.50 1.00 2.00 2.50 2/ 224 316 350 350 350 350 350 160 200 200 200 200 200 200 1/ Rated for continuous working voltage at 70OC. 2/ For replacement purposes only

13、. Not for new design. 3.3.1 Resistance value deviations. All maximum deviations as specified in this section are to be considered absolute limits with the exception of the contact resistance adjustments. 3.4 Shaft length. The length of the operating shall be in accordance with table II. TABLE II Sha

14、ft length. Length of shafts from mounting surface at resistors Nominal (in inches 0.03125) Symbol Bushing N Bushing L B D L 0.875 0.375 0.5000.8751/ 1/ For replacement purposes only, not for new design. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,

15、-MIL-PRF-94/2E w/Amendment 1 3Inches mm Inches mm Inches mm Inches mm 0.001 0.03 0.031 0.79 0.080 2.03 0.375 9.53 0.003 0.08 0.040 1.02 0.094 2.39 0.562 14.27 0.005 0.13 0.047 1.19 0.125 3.18 0.656 16.66 0.016 0.41 0.050 1.27 0.250 6.35 0.750 19.05 NOTES: 1. Dimensions are in inches. Metric equivale

16、nts are given for general information. 2. Unless otherwise specified, tolerance is 0.016 inch (0.41mm). FIGURE 1. Style RV5. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-94/2E w/Amendment 1 43.5 Mounting and locking nuts. The mounting nut

17、shall be 0.09375 inches thick and measure 0.375 inches across the hexagonal flats. The locking nut shall be 0.125 inches thick and shall measure 0.375 inches across the hexagonal flats. The thread size shall be 0.25-32 NEF-2B. 3.5.1 Internal tooth lockwasher. Internal tooth lockwasher of suitable si

18、ze shall be applied. 3.5.2 Retainer rings. If retainer rings are used, shall have a maximum thickness of 0.032 inches. 3.6 Power rating. The power rating shall be 0.5 watts for taper A resistors and 0.25 watts for taper C and F resistors. 3.7 Torque. 3.7.1 Operating torque. The torque required to ef

19、fect rotation shall be 0.50 ounce-inch minimum and 6 ounce-inch maximum. 3.7.2 Stop torque. The torque applied to the operating shaft to the stops shall be 5 pound-inch. 3.7.3 Locking torque (as applicable). For the locking bushing type resistors, the locking nut shall be tightened with a torque of

20、10 pound-inches. After the locking nut is tightened, the contact arm shall not move when a torque of 20 ounce-inches is applied to the shaft. 3.8 Total mechanical rotation. The total mechanical rotation without a switch shall be within the limits of 295 degrees and 305 degrees. 3.9 Thermal cycling.

21、The resistance shall not change in excess of 6 percent. 3.10 Pure tin. The use of pure tin, as an underplate or final finish, is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 per

22、cent lead, by mass (see 6.3). 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection shall be in accordance with MIL-PRF-94. 4.2 Dielectric withstanding voltage. In the dielectric withstanding voltage test, the applied potential at reduced barometric pressure shall be 350 volts, rms. 5

23、. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascer

24、tain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defens

25、e Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. The intended use specified in MIL-PRF-94 is applicab

26、le to this specification. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-94/2E w/Amendment 1 56.2 Acquisition requirements. Acquisition documents must specify the following: a. Title, number, and date of this specification, and the complete

27、PIN (see 1.2). b. If not otherwise specified (see 2.1), the versions of the individual documents referenced will be those in effect on the date of release of the solicitation. c. Packaging instructions (see 5.1). 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by

28、mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not preve

29、nt the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.4 Amendment notification. The margins of this specific

30、ation are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this

31、 document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 DLA CC Review activities (Project 5905-2008-046) Army - AT, AV, CR4, MI Navy - AS, MC Air Force - 19,

32、99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-