DLA MIL-PRF-39012 135 C-2012 CONNECTORS RECEPTACLE ELECTRICAL COAXIAL RADIO FREQUENCY SERIES SSMB PRINTED CIRCUIT BOARD MOUNT RIGHT ANGLE.pdf

《DLA MIL-PRF-39012 135 C-2012 CONNECTORS RECEPTACLE ELECTRICAL COAXIAL RADIO FREQUENCY SERIES SSMB PRINTED CIRCUIT BOARD MOUNT RIGHT ANGLE.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-39012 135 C-2012 CONNECTORS RECEPTACLE ELECTRICAL COAXIAL RADIO FREQUENCY SERIES SSMB PRINTED CIRCUIT BOARD MOUNT RIGHT ANGLE.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5935 INCH-POUND MIL-PRF-39012/135C 2 July 2012 SUPERSEDING MIL-PRF-39012/135B 29 June 1994 PERFORMANCE SPECIFICATION SHEET CONNECTORS, RECEPTACLE, ELECTRICAL, COAXIAL, RADIO FREQUENCY, SERIES SSMB, PRINTED CIRCUIT BOARD MOUNT, RIGHT ANGLE This specification is approved for use by all De

2、partments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-39012. FIGURE 1. General configuration. Inactive for new design after 02 July 2012. Provided by IHSNot for ResaleNo reproduction or n

3、etworking permitted without license from IHS-,-,-MIL-PRF-39012/135C 2 NOTES: 1. Dimensions are in inches 2. Metric equivalents are given for general information only. 3. All undimensioned pictorial configurations are for reference purposes only. 4. Unless otherwise specified tolerances shall be .005

4、 (0.13mm). 5. Connector bodies shall be gold plated in accordance with ASTM B488, type 3, grade C, class 1.27. 6. Series SSMB pin contact interface shall be in accordance with MIL-STD-348. 7. Connector bodies shall be silver plated in accordance with MIL-PRF-39012. 8. Configuration of base optional.

5、 Dimension .225 is the maximum envelope diameter. 9. Center contact shall be one piece or shall be manufactured in such a way that it is not damaged during normal manufacturing operations when the connector is soldered to a printed wiring board. FIGURE 1. General configuration Continued. ENGINEERING

6、 DATA: Nominal impedance: 50 ohms. Frequency range: 0 to 12.4 GHz. Voltage rating: 250 volts rms, maximum working voltage at sea level. 60 volts rms, maximum at 70,000 feet (4.437 kPa). Temperature rating: - 65C to + 165C. REQUIREMENTS: Dimensions and configurations: See figure 1 and MIL-STD-348. Fo

7、rce to engage and disengage: Longitudinal force: Not applicable. Torque : Not applicable. Coupling proof torque: Not applicable. Inspection conditions: Not applicable. Mating characteristics: In accordance with MIL-STD-348. Hermetic seal: Not applicable. Leakage (pressurized connector): Not applicab

8、le. Dash number Dimension A 0001 (see note 5) .155(3.94) .010 (0.25) 0002 (see note 5) .125 (3.18) .010 (0.25) 0003 (see note 5) .093 (2.36) .010 (0.25) 0004 (see note 7) .155 (3.94) .010 (0.25) 0005 (see note 7) .125 (3.18) .010 (0.25) 0006 (see note 7) .093 (2.36) .010 (0.25) Inches mm Inches mm .

9、001 0.02 .050 1.27 .002 0.05 .100 2.54 .004 0.10 .218 5.54 .026 0.66 .221 5.61 .030 0.76 .385 9.78 .036 0.91 .435 11.05 .038 0.97 .600 15.24 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/135C 3 Insulation resistance: In accordance wit

10、h MIL-STD-202, method 302, test condition B, 1,000 mega ohms minimum. Center contact retention: Minimum axial force : 2 pounds from mating end. Solderability: For quality conformance inspection, the test shall be performed in group B following VSWR; test 5 samples with no failures permitted. In acco

11、rdance with MIL-STD-202, method 208. Corrosion (salt spray): In accordance with MIL-STD-202, method 101, test condition B. Voltage standing wave ratio (VSWR): Not applicable. Connector durability: 500 cycles minimum at 12 cycles/minute maximum. Initial: 6.0 pound maximum engage. Final: 6.0 pound max

12、imum engage and disengage. 1.0 pound minimum disengagement. Contact resistance: In milliohms maximum: Initial After environment Center contact 4.0 6.0 Outer contact 1.0 1.5 Braid to body Not applicable Not applicable Dielectric withstanding voltage: In accordance with MIL-STD-202, method 301, 500 vo

13、lts rms minimum at sea level. Vibration, high frequency: In accordance with MIL-STD-202, method 204, test condition B, 15 Gs. Shock: In accordance with MIL-STD-202, Method 213, test condition B, 75gs at 6 milliseconds, sine. Thermal shock: In accordance with MIL-STD-202 , method 107, test condition

14、B. Moisture resistance: Not applicable. Corona Level: 125 V up to 75,000 feet. RF high potential withstanding voltage: Voltage and frequency: 400 volts rms at a frequency at 5 MHz. Leakage current: Not applicable. Cable retention force: Not applicable. Coupling mechanism retention force: Not applica

15、ble. RF leakage: Not applicable. Insertion loss: Not applicable. Part or Identifying Number (PIN): M39012/135 (dash number from figure 1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/135C 4 Group qualification: See table I. TABLE I.

16、 Group qualification and retention testing. Group Submission and qualification of any of the following connectors 1/ Qualifies the following connectors I M39012/133-0001 M39012/133-0002 M39012/133-0003 M39012/134-0001 M39012/134-0002 M39012/134-0003 M39012/133-0001 M39012/133-0002 M39012/133-0003 M3

17、9012/134-0001 M39012/134-0002 M39012/134-0003 II M39012/133-0004 M39012/133-0005 M39012/133-0006 M39012/134-0004 M39012/134-0005 M39012/134-0006 M39012/133-0004 M39012/133-0005 M39012/133-0006 M39012/134-0004 M39012/134-0005 M39012/134-0006 1/ For qualification retention, where more than one part is

18、 listed in a group in this column, data may be supplied on any of these parts in order to retain qualification for those parts in the corresponding right hand column. The part used for qualification retention does not have to be the part initially qualified. Changes from previous. The margins of thi

19、s specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requiremen

20、ts of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-PRF-39012, this document references the following: ASTM B488 MIL-STD-202 MIL-STD-348 Provided by IHSNot for ResaleNo reproducti

21、on or networking permitted without license from IHS-,-,-MIL-PRF-39012/135C 5 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5935-2012-107) DLA - CC Review activities: Army - AR, AT, MI Navy - AS, MC, OS, SH Air Force - 19, 99 NASA - NA NOTE:

22、The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-