DLA MIL-PRF-39012 134 B-2012 CONNECTORS RECEPTACLE ELECTRICAL COAXIAL RADIO FREQUENCY SERIES SMC PRINTED CIRCUIT BOARD MOUNT RIGHT ANGLE.pdf

《DLA MIL-PRF-39012 134 B-2012 CONNECTORS RECEPTACLE ELECTRICAL COAXIAL RADIO FREQUENCY SERIES SMC PRINTED CIRCUIT BOARD MOUNT RIGHT ANGLE.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-39012 134 B-2012 CONNECTORS RECEPTACLE ELECTRICAL COAXIAL RADIO FREQUENCY SERIES SMC PRINTED CIRCUIT BOARD MOUNT RIGHT ANGLE.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5935 INCH-POUND MIL-PRF-39012/134B 2 July 2012 SUPERSEDING MIL-PRF-39012/134A 15 November 1993 PERFORMANCE SPECIFICATION SHEET CONNECTORS, RECEPTACLE, ELECTRICAL, COAXIAL, RADIO FREQUENCY, SERIES SMC, PRINTED CIRCUIT BOARD MOUNT, RIGHT ANGLE This specification is approved for use by all

2、 Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-39012. FIGURE 1. General configuration. Inactive for new design after 02 July 2012. Provided by IHSNot for ResaleNo reproduction o

3、r networking permitted without license from IHS-,-,-MIL-PRF-39012/134B 2 NOTES: 1. Dimensions are in inches 2. Metric equivalents are given for general information only. 3. All undimensioned pictorial configurations are for reference purposes only. 4. Configuration of base optional. Dimension specif

4、ied in the maximum envelope diameter of feature. 5. Connector bodies shall be gold plated in accordance with ASTM B488, type 3, grade C, class 1.27. 6. Series SMC interface shall be in accordance with MIL-STD-348. 7. Connector bodies shall be silver plated in accordance with MIL-PRF-39012. 8. Center

5、 contact shall be one piece or shall be manufactured in such a way that it is not damaged during normal manufacturing operations when the connector is soldered to a printed wiring board. FIGURE 1. General configuration Continued. ENGINEERING DATA: Nominal impedance: 50 ohms. Frequency range: 0 to 4

6、GHz. Voltage rating: 335 volts rms, maximum working voltage at sea level. 85 volts rms, maximum at 70,000 feet (4.437 kPa). Temperature rating: - 65C to + 165C. REQUIREMENTS: Dimensions and configurations: See figure 1 and MIL-STD-348. Force to engage and disengage: Longitudinal force: Not applicabl

7、e. Torque 16 inch-ounces , maximum. Coupling proof torque: Not applicable. Inspection conditions: Coupling torque: 35 50 inch-ounces Mating characteristics: In accordance with MIL-STD-348. Hermetic seal: Not applicable. Dash number Dimension A 0001 (see note 5) .155(3.94) .010 (0.25) 0002 (see note

8、5) .125 (3.18) .010 (0.25) 0003 (see note 5) .093 (2.36) .010 (0.25) 0004 (see note 7) .155 (3.94) .010 (0.25) 0005 (see note 7) .125 (3.18) .010 (0.25) 0006 (see note 7) .093 (2.36) .010 (0.25) Inches mm Inches mm .001 0.02 .067 1.70 .002 0.05 .100 2.54 .003 0.08 .200 5.08 .008 0.20 .218 5.54 .020

9、0.51 .375 9.52 .038 0.97 .385 9.78 .058 1.47 .435 11.05 .060 1.52 .615 15.62 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/134B 3 Leakage (pressurized connector): Not applicable. Insulation resistance: In accordance with MIL-STD-202,

10、Method 302. 1,000 Mega ohms minimum. Center contact retention: Minimum axial force : 6 pounds from mating end. 4 pounds from opposite end. Torque: 3 inch-ounces. Solderability: For quality conformance inspection, the test shall be performed in group B following VSWR; test 5 samples with no failures

11、permitted. In accordance with MIL-STD-202, Method 208. Corrosion (salt spray): In accordance with MIL-STD-202, Method 101, test condition B. Voltage standing wave ratio (VSWR): Not applicable. Connector durability: Insertion and withdrawal force: 500 cycles minimum at 12 cycles/minute maximum. The c

12、onnector shall meet the mating characteristics and force to engage end disengage requirements. Contact resistance: In milliohms maximum: Initial After environment Center contact 6.0 8.0 Outer contact 1.0 1.5 Braid to body Not applicable Not applicable Dielectric withstanding voltage: In accordance w

13、ith MIL-STD-202, Method 301, 1,000 volts rms minimum at sea level. Vibration, high frequency: In accordance with MIL-STD-202, Method 204, test condition D. Shock: In accordance with MIL-STD-202, Method 213, test condition C. Thermal shock: In accordance with MIL-STD-202 , Method 107, test condition

14、B. Moisture resistance: Not applicable. Corona Level: Not applicable. RF high potential withstanding voltage: Voltage and frequency: 600 volts rms at a frequency at 5 MHz. Leakage current: Not applicable. Cable retention force: Not applicable. Coupling mechanism retention force: Not applicable. RF l

15、eakage: Not applicable. Insertion loss: Not applicable. Part or Identifying Number (PIN): M39012/134 (dash number from figure 1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/134B 4 Group qualification: See table I. TABLE I. Group qu

16、alification and retention testing. Group Submission and qualification of any of the following connectors 1/ Qualifies the following connectors I M39012/133-0001 M39012/133-0002 M39012/133-0003 M39012/134-0001 M39012/134-0002 M39012/134-0003 M39012/133-0001 M39012/133-0002 M39012/133-0003 M39012/134-

17、0001 M39012/134-0002 M39012/134-0003 II M39012/133-0004 M39012/133-0005 M39012/133-0006 M39012/134-0004 M39012/134-0005 M39012/134-0006 M39012/133-0004 M39012/133-0005 M39012/133-0006 M39012/134-0004 M39012/134-0005 M39012/134-0006 1/ For qualification retention, where more than one part is listed i

18、n a group in this column, data may be supplied on any of these parts in order to retain qualification for those parts in the corresponding right hand column. The part used for qualification retention does not have to be the part initially qualified. Changes from previous. The margins of this specifi

19、cation are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of thi

20、s document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/134B 5 Referenced documents. In addition to MIL-PRF-39012, this d

21、ocument references the following: ASTM B488 MIL-STD-202 MIL-STD-348 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5935-2012-106) DLA - CC Review activities: Army - AR, AT, MI Navy - AS, MC, OS, SH Air Force - 19, 99 NASA - NA NOTE: The activ

22、ities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-