DLA MIL-DTL-24211 1 D-2013 GASKETS WAVEGUIDE FLANGE (COVER).pdf

《DLA MIL-DTL-24211 1 D-2013 GASKETS WAVEGUIDE FLANGE (COVER).pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-24211 1 D-2013 GASKETS WAVEGUIDE FLANGE (COVER).pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5985 INCH-POUND MIL-DTL-24211/1D 6 November 2013 SUPERSEDING MIL-DTL-24211/1C 20 March 2009 DETAIL SPECIFICATION SHEET GASKETS, WAVEGUIDE FLANGE (COVER) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring th

2、e gaskets described herein shall consist of this specification sheet and MIL-DTL-24211. REQUIREMENTS: Dimensions and configuration: See figure 1. Reference data: See table I. Part number: Consists of the basic number of this specification sheet and a dash number from table I. Example: M24211/1 -001

3、Basic document number Dash number from table I TABLE I. Reference data. Part number M24211/1- Used with flanges 1/ Part number M24211/1- Used with flanges 1/ 001 UG-51/U and UG-138/U 004 UG-1530/U 002 UG-39/U and UG-135/U 005 UG-595/U and UG-597/U 003 UG-419/U and UG-1665/U 006 UG-599/U 1/ Flanges a

4、re in accordance with MIL-DTL-3922. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24211/1D 2 FIGURE 1. Dimensions and configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-2

5、4211/1D 3 Part number M24211/1- A B C D E .01 (.25) G .01 (.25) 001 1.122 .004 (28.50 .10) .497 .004 (12.62 .10) .561 .002 (14.25 .05) .2485 .0020 (6.31 .05) 1.532 (38.91) .907 (23.04) 002 .900 .003 (22.86 .08) .400 .003 (10.16 .08) .4500 .0015 (11.43 .04) .2000 .0015 (5.08 .04) 1.300 (33.02) .800 (

6、20.32) 003 .622 .002 (15.80 .05) .311 .002 (7.90 .05) .311 .001 (7.90 .03) .1555 .0010 (3.95 .03) 1.006 (25.55) .695 (17.65) 004 .340 .002 (8.64 .05) .170 .002 (4.32 .05) .170 .001 (4.32 .03) .085 .001 (2.16 .03) .580 (14.73) .410 (10.41) 005 .420 .002 (10.67 .05) .170 .002 (4.32 .05) .210 .001 (5.3

7、3 .03) .085 .001 (2.16 .03) .660 (16.76) .410 (10.41) 006 .2800 .0015 (7.11 .04) .1400 .0015 (3.56 .04) .1400 .0008 (3.56 .02) .0700 .0008 (1.78 .02) .474 (12.04) .334 (8.48) Part number M24211/1- K L .01 (.25) M .02 (.51) N S .003 (.08) U .02 (.51) V . .005 (.13) W .005 (.13) X Min 001 .676 .002 (1

8、7.17 .05) .94 (23.88) 1.88 (47.75) .737 .002 (18.72 .05) .169 (4.29) 1.25 (31.75) .026 (.66) .110 (2.79) .064 (1.63) 002 .610 .002 (15.49 .05) .82 (20.83) 1.63 (41.40) .640 .002 (16.26 .05) .169 (4.29) 1.06 (26.92) .026 (.66) .110 (2.79) .050 (1.27) 003 .497 .002 (12.62 .05) .66 (16.76) 1.31 (33.27)

9、 .478 .002 (12.14 .05) .144 (3.66) .88 (22.35) .026 (.66) .110 (2.79) .040 (1.02) 004 .320 .001 (8.13 .03) .44 (11.18) .88 (22.35) .335 .001 (8.51 .03) .116 (2.95) .57 (14.48) .020 (.51) .100 (2.54) .040 (1.02) 005 .320 .001 (8.13 .03) .44 (11.18) .88 (22.35) .335 .001 (8.51 .03) .116 (2.95) .57 (14

10、.48) .020 (.51) .100 (2.54) .040 (1.02) 006 .250 .001 (6.35 .03) .38 (9.65) .75 (19.05) .265 .001 (6.73 .03) .116 (2.95) .47 (11.94) .015 (.38) .080 (2.03) .040 (1.02) NOTES: 1. Dimensions are in inches. 2. Millimeters are in parentheses. 3. Metric equivalents (to the nearest 0.01 mm) are given for

11、general information only and are based upon 1 inch = 25.4 mm. 4. Except where noted, break sharp edges and remove burrs. 5. Flange is symmetrical about both centerlines. 6. Electrical contact area to be at least 0.003 (0.08) higher than adjacent metal surface. 7. Surface roughness of mating surfaces

12、 other than the raised electrical contact area shall be no greater than 63 micro inches in accordance with ASME-B46.1. 8. Any raised embossed pattern for electrical contact is acceptable provided R.F. leakage requirement is met. FIGURE 1. Dimensions and configuration. Continued Provided by IHSNot fo

13、r ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24211/1D 4 Referenced documents. In addition to MIL-DTL-24211, this document references the following: MIL-DTL-3922 ASME-B46.1 Marginal notations are not used in this revision to identify changes with respect to the

14、 previous issue due to the extent of the changes. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5985-2013-047) Review activities: Army - MI, AR Navy - OS, CG, SH Air Force - 19 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-