DLA MIL-C-43358 B-1988 CLOTH KNITTED NYLON ACETATE TRICOT CAMOUFLAGE GREEN 483《绿色483尼龙 醋酸绒线针织布》.pdf

《DLA MIL-C-43358 B-1988 CLOTH KNITTED NYLON ACETATE TRICOT CAMOUFLAGE GREEN 483《绿色483尼龙 醋酸绒线针织布》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-C-43358 B-1988 CLOTH KNITTED NYLON ACETATE TRICOT CAMOUFLAGE GREEN 483《绿色483尼龙 醋酸绒线针织布》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、3i MIL-C-q3358B 83 999770b 0393283 L W Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014 by using the self- ad

2、dressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. u -37- 15 MIL-C-43358B 26 August 1988 SUPERSEDING 11 April 1972 MIL -C-4 3358A MILITARY SPECIFICATION * CLOTH, KNITTED, NYLON/ACETATE, TRICOT, CAMOUFLAGE GREEN 483 This specificat

3、ion is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE * 1.1 Scope. This document covers one type of nylon/acetate tricot knitted cloth, Camouflage Green 483. 2. APPLICABLE DOCUMENTS 2.1 Government documents. * 2.1.1 Specifications, standards, and handbooks. T

4、he following specifications, standards, and handbooks form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplem

5、ent thereto, cited in the solicitation. SPECIFICATION FEDERAL PPP-P-1133 - Packaging of Synthetic Fiber Fabrics = AMSC N/A FSC 8305 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. - . THIS DOCUMENT CONTAINS / PAGES. - B =- .- = - - -=_- -= Provided by IHSNot for Res

6、aleNo reproduction or networking permitted without license from IHS-,-,- VIL-C-Lt335B 3 7777706 0373284 3 W * s MIL-C-4 3 358B STAN DARDS FEDERAL FED-STD-191 - Textile Test Methods MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes (Copies of specifications, standards

7、, and handbooks required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) * 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings,

8、and publications form a part of this specification to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the solicitation. Rules and Regulations Under the Textile Fiber Products Identification Act (Copies may be obtained from the Federal Trade

9、 Commission, Pennsylvania Avenue at Sixth Street, N.W., Washington, DC 20508-0001.) (Copies of drawings, publications, and other Government documents required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contr

10、acting activity.) 2.2 Other publications. The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the.issue of the DODISS specified in the solicitation. Unless oth

11、erwise specified, the issues of documents not listed in the DODISS shall be the issues of the nongovernment documents which are current on the date of the solicitation. AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS ( AATCC) Chromatic Transference Scale (Copies should be obtained from the Am

12、erican Association of Textile Chemists and Colorists, P.O. Box 12215, Research Triangle Park, NC 27709-2215.) (Nongovernment standards and other publications are normally available from the organizations which prepare or which distribute the documents. These documents also may be available in or thr

13、ough libraries or other informational services. I- -_ ,f- 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2 MIL-C-Y3358B 83 m 7777706 0373285 5 W MIL-C-43358B * 2.3 Order of precedence. In the event of a conflict between the text of this specificat

14、ion and the references cited herein, the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS i 3.1 Standard sample. The finished cloth shall match the

15、standard sample for shade and appearance and shall be equal to or better than the standard sample with respect to all characteristics for which the standard sample is referenced (see 6.3). * 3.2 First article. When specified in the contract or purchase order, a sample shall be subjected to first art

16、icle inspection (see 4.3, 6.2, and 6.4). 3.3 Material. * 3.3.1 Yarn. The yarn for the back bar shall be multifilament semidull, normal tenacity nylon and the yarn for the front bar shall be multifilament acetate yarn (see 6.5). * 3.4 Color. The color of the finished cloth shall be Camouflage Green 4

17、83. * 3.4.1 Matching. The color of the finished cloth shall match the standard sample when viewed under filtered tungsten lamps that approximate artificial daylight and that have a correlated color temperature of 7500 2 200K, with illumination of 100 2 20 foot candles and shall be a good match to th

18、e standard sample under incandescent lamplight at 2300 2 200K. * 3.4.2 Colorfastness. The finished cloth shall show fastness to laundering and perspiration equal to or better than the standard sample or equal to or better than arating of “good.“ crocking equal to or better than the standard sample o

19、r shall have an AATCC Chromatic Transference Scale rating not lower than 3.5. specified in 4.4.3. The finished cloth shall show fastness to Testing shall be as 3.5 Physical requirements. The finished cloth shall conform to the requirements specified in table I when tested as specified in 4.4.3. TABL

20、E I. Physical requirements Weight oz/yd2 Yarns per inch, min Bursting strength, min Thickness, min Min Max Wales Courses Pounds Inches 5.0 6.5 40 47 45 0.065 3 a Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ _ MIL-C-43358B 83 M 7779706 03732b 7 M

21、IL-C-43358B 3.5.1 - Knit. 3.5.2 Width. The width of the cloth shall be as specified (see 6.2) and The cloth shall be warp knitted in such a manner that the acetate yarn will be run in to produce a long float. shall be the minimum acceptable width inclusive of selvages. 3.6 Finish. The cloth shall be

22、 thoroughly scoured and heat set. The long floats on the reverse side of the cloth shall be napped and sheared so as to produce a uniform density of pile throughout the surface to meet the physical requirements specified in table I. The character of the napped surface shall be equal to that exhibite

23、d by the standard sample. 3.6.1 pH. The pH value of the water extract of the finished cloth shall be no less than 5.0 nor more than 8.5 when tested as specified in 4.4.3. * 3.7 Shrinkage requirements. The finished cloth shall not shrink or elongate more than 3.0 percent in length (wale direction) or

24、 5.0 percent in width (course direction) when tested as specified in 4.4.3. 3.8 Nonfibrous material content. The starch and protein content of the finished cloth, including carbon-tetrachloride-soluble and water-soluble material, shall not exceed 2.0 percent when tested as specified in 4.4.3. 3.9 Le

25、ngth and put-up. Unless otherwise specified (see 6.2), the cloth shall be one continuous piece of not less than 40 yards and shall be put up in rolls as specified in 5.1.1. 3.10 Fiber identification. Each roll shall be labeled, ticketed, or invoiced for fiber content in accordance with the Textile F

26、iber Products Identification Act. 3.11 Workmanship. The cloth shall conform to the quality of product established by this document and the occurrence of defects shall not exceed the applicable acceptable quality levels. 4, QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherw

27、ise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance

28、of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this document where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4 f-c-

29、 - -? Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-C-9335E 3 7997906 0393287 7 - - MIL-C-43358B * 4.1.1 Responsibility for compliance. All items must meet all requirements of sections 3 and 5. The inspection set forth in this document shall b

30、ecome a part of the contractors overall inspection system or quality program. The absence of any inspection requirement in the document shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requirem

31、ents of the contract. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective material. a * 4.1.2 Responsibility for dimensional requirements. Unless otherwise specified in the

32、 contract or purchase order, the contractor is responsible for assuring that all specified dimensions have been met. When dimensions cannot be examined on the end item, inspection shall be made at any point or at all points in the manufacturing process necessary to assure compliance with all dimensi

33、onal requirements. 4.1.3 Certificates of compliance. When certificates of compliance are submitted, the Government reserves the right to inspect such items to determine the validity of the certification. * 4.2 Classification of inspections. The inspection requirements specified herein are classified

34、 as follows: a. First article inspection (see 4.3). b. Quality conformance inspection (see 4.4). * 4.3 First article inspection. When a first article is required (see 6.21, it shall be examined for the defects specified in 4.4.2.1 and shall be tested for the characteristics specified in table IV. Th

35、e presence of any defect or failure of any test shall be cause for rejection of the first article. 4.4 Quality conformance inspection. Unless otherwise specified, sampling for inspection shall be performed in accordance with MIL-STD-105. 4.4.1 Component and material inspection. In accordance with 4.

36、1, components and materials shall be inspected in accordance with all the requirements of referenced documents unless otherwise excluded, amended, modified, or qualified in this document or applicable purchase document. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without l

37、icense from IHS-,-,-MIL-C-43358B 4.4.2 End item examination. /- 4.4.2.1 Yard-by-yard examination. The cloth shall be examined on the unnapped face side for the defects listed in table II. All defects found shall be counted regardless of their proximity to each other, except where two or more defects

38、 represent a single local condition of the cloth in which case only the more serious defect shall be counted. A continuous defect shall be counted as one defect for each wale-wise (lengthwise) yard or fraction thereof in which it occurs. The lot size shall be expressed in units of yards. The sample

39、unit shall be 1 linear yard. The inspection level shall be II and the acceptable quality level (AQL), expressed in terms of defects per hundred units, shall be 2.5 for major defects and 10.0 for total (major and minor) combined defects. The number of rolls from which the sample yardage is to be sele

40、cted shall be in accordance with table II. The sample yardage shall be apportioned equally among the selected rolls. TABLE II. Yard-by-yard examination defects Defect Classification Major Minor Any hole, cut, tear Run, missing yarn Any float on unnapped side more than 1/4 inch Tucking defect, snag,

41、or needle line Mend Abrasion mark resulting in a weak area Thin or thick places Heavy or thin yarn - 1/ Tight twist yarn Slubs or slugs more than twice the size of Foreign matter 1/ Knots, oversize, extending above the surface of cloth Kinks or untrimmed ends Tight yarn or loose yarn Barre 1/ Spot O

42、F stain normal yarn X X X X X X X X X X X X X X X X - 1/ Clearly visible at normal inspection distance (approximately 3 feet). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-V3358B 83 W 777770b 0373287 2 W MIL -C-43 358B 4.4.2.2 Overall examin

43、ation. The cloth shall be examined for the defects O listed below. Each defect listed shall be counted not more than once in each roll examined. The sample size shall be the applicable number of rolls indicated in table III. Each roll in the sample shall be examined over its entire length. The lot s

44、hall be rejected if the total number of defects in the sample exceeds the applicable acceptance number specified in table III. Defects Width less than specified Objectionable odor Overall uncleanness Uneven knitting throughout the piece Off shade, shaded end to end, side to side, side to center, or

45、Poor dye penetration, mottled, streaky, or cloudy Character of napped surface not equal to the standard sample Not labeled in accordance with the Textile Fiber Products throughout the roll Identification Act TABLE III. Sample size a Sample size Lot size (yards) (roils) Acceptance number Up to 1,300

46、1/ 3 1,301 up to and including 3,200 5 3,201 up to and including 8,000 7 8,001 up to and including 22,000 10 22,001 up to and including 110,000 15 110,001 and over 25 I/ If a lot contains fewer than three rolls, each roll in the lot shall be - examined. 4.4.2.3 Length examination. During the overall

47、 examination, each roll in the sample shall be examined for gross length. If the total of the actual gross lengths of the rolls in the sample is less than the total of the gross lengths marked on the roll tickets, the lot shall be rejected. 7 Provided by IHSNot for ResaleNo reproduction or networkin

48、g permitted without license from IHS-,-,-_- c-I-_ -I_- MIL-C-43358B 83 - 999790b 0393270 7 - MIL-C-43 358B 4.4.3 End item testing. The cloth shall be tested for the characteristics listed in table IV. The methods of testing specified in FED-STD-191, wherever applicable, and as listed in table IV sha

49、ll be followed. contain the individual values utilized in expressing the final results. The sample unit shall be 3-1/2 continuous yards full width of the cloth. shall be rejected if one or more sample units fail to meet any requirement specified. All test reports shall The lot The sample size shall be in accordance with the following: Lot size (yards) 800 or less 801 up t