DLA DSCC-DWG-87122 REV H-2009 CAPACITORS CERAMIC SINGLE IN-LINE PACKAGE NETWORK (4 CAPACITOR SECTIONS) BX.pdf

《DLA DSCC-DWG-87122 REV H-2009 CAPACITORS CERAMIC SINGLE IN-LINE PACKAGE NETWORK (4 CAPACITOR SECTIONS) BX.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-87122 REV H-2009 CAPACITORS CERAMIC SINGLE IN-LINE PACKAGE NETWORK (4 CAPACITOR SECTIONS) BX.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Added suggested source of supply. 10 Jan 90 David E. Moore B Deleted suggested source of supply. 29 Jun 90 David E. Moore C Deleted and added suggested sources of supply. Modified 3.1.2 and figure 1. Added note for standoff. Editorial changes throughout. 24

2、 Feb 92 David E. Moore D Changes in accordance with NOR 5910-R017-96 23 May 96 Andrew R. Ernst E Added and removed suggested sources of supply. 25 August 99 Kendall A. Cottongim F Removed suggested source of supply. 10 May 00 Kenneth A. Bernier G Editorial changes made throughout. 6 October 2004 Ken

3、dall A. Cottongim H Changed drawing to source control with approved sources of supply. Added pure tin prohibition paragraph 3.1.3 and manufacturer eligibility paragraph 3.14. Editorial changes. 15 Dec 09 Michael A. Radecki Prepared in accordance with ASME Y14.100 Source Control drawing REV STATUS RE

4、V H H H H H H H OF PAGES PAGES 1 2 3 4 5 6 7 PMIC N/A PREPARED BY ROBERT E. GRILLOT DESIGN ACTIVITY DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OH 45444-5000 Original date of drawing: 22 December 1987 CHECKED BY HERALDINE JOHNSON TITLE CAPACITORS, CERAMIC, SINGLE IN-LINE PACKAGE, NETWORK, (4 CAPACITOR

5、SECTIONS) BX APPROVED BY DAVID W. WITHROW SIZE A CODE IDENT. NO. 14933 DWG NO. 87122 REV H PAGE 1 OF 7 AMSC N/A 5910-E451 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networki

6、ng permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87122 REV H PAGE 2 1. SCOPE 1.1 Scope. This drawing, MIL-PRF-39014, and MIL-PRF-39014/5 describe the complete requirements for single-in-line packaged multilayer ceramic capac

7、itor networks. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specif

8、ication or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this specification, whether or not they are list

9、ed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract.

10、 DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-39014 - Capacitors, Fixed, Ceramic Dielectric (General Purpose) Established Reliability and Nonestablished Reliability, General Specification for. MIL-PRF-39014/5 - Capacitors, Fixed, Ceramic Dielectric (General Purpose), Established Reliability, Styles

11、CKR11, CKR12, CKR14, CKR15, and CKR16. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Electronics and Electrical Component Parts. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardi

12、zation Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes preceden

13、ce. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-39014 and herein (see figure 1). 3.1.1 Leads.

14、 Leads shall be as specified on figure 1. 3.1.2 Case. Molded or conformally coated. 3.1.3 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of capacitor components and solder shall not exceed 97 percent, by mass. Tin shall be al

15、loyed with a minimum of 3 percent lead, by mass (see 6.3). 3.1.4 Operating temperature range. The operating temperature range shall be -55C to +125C. 87122- XX Drawing number Dash number (see table I) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-D

16、EFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87122 REV H PAGE 3 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Standoff shape is optional. The minimum height of the standoff shall be .015 (0.38 mm). 4. Lead sp

17、acing: .100 .010 (25.4 0.25) noncumulative. FIGURE 1. Case dimensions and configuration. Inches mm Inches mm .002 .003 .004 .010 .012 .015 .018 0.05 0.08 0.10 0.25 0.30 0.38 0.46 .058 .060 .100 .115 .135 .300 .850 1.47 1.52 2.54 2.92 3.43 7.62 21.59 Provided by IHSNot for ResaleNo reproduction or ne

18、tworking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87122 REV H PAGE 4 3.2 Electrical characteristics. 3.2.1 Rated voltage. The rated voltage shall be 100 V dc at +85C, 50 V dc at +125C. 3.2.2 Dielectric type. BX, in acco

19、rdance with MIL-PRF-39014/5. 3.2.3 Voltage temperature limits. In accordance with MIL-PRF-39014/5. 3.2.4 Capacitance. See table I. Measured in accordance with method 305 of MIL-STD-202, 1 kHz at 1.0 V rms at +25C. 3.2.5 Dissipation factor (+25C). 2.5 percent maximum (measured under the same conditio

20、ns as capacitance). 3.2.6 Insulation resistance. Measured in accordance with method 302 of MIL-STD-202. At +25C, rated voltage: 100,000 megohms or 1,000 megohms microfarad, whichever is less. 3.2.7 Dielectric withstanding voltage. Capacitors shall withstand a dc test potential of 250 percent of rate

21、d voltage for a period of not less than 1 second nor more than 5 seconds at +25C. The charging current shall not exceed 50 milliamperes. 3.2.8 Capacitance tolerance. K = 10 percent, M = 20 percent. 3.3 Solderability of terminals. In accordance with MIL-PRF-39014. 3.4 Vibration. In accordance with me

22、thod 204 of MIL-STD-202, test condition B (10 to 20,000 Hz, 15 gs). 3.5 Shock. In accordance with MIL-PRF-39014. 3.6 Immersion cycling. In accordance with MIL-PRF-39014. 3.7 Moisture resistance. In accordance with MIL-PRF-39014. 3.8 Life. 200 percent of rated voltage applied at +125C for 1,000 hours

23、. 3.9 Thermal shock. In accordance with method 107 of MIL-STD-202, test condition B except low temperature is -55C. 3.10 Voltage conditioning. In accordance with MIL-PRF-39014, 200 percent of rated voltage. 3.11 Terminal strength. Capacitors shall withstand a steady pull of 5 pounds for 5 seconds in

24、 a direction parallel to the leads. 3.12 Marking. Marking shall be in accordance with MIL-STD-1285 except the capacitors shall be marked with the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, and date lot code as a minimum. 3.13 Recycled,

25、recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle c

26、osts. 3.14 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-123, MIL-PRF-39014, or MIL-PRF-49470 Qualified Products Database for at least one part, or perform the group A and group B inspections specified herein on a

27、sample of parts agreed upon by the manufacturer and DSCC-VA. 3.15 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.16 Workmanship. Capacitors shall be uniform in quality and free from any defects that will af

28、fect life, serviceability, or appearance. 4. VERIFICATION 4.1 Sampling and inspection. Qualification sampling and inspection are not required. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE

29、IDENT NO. 14933 DWG NO. 87122 REV H PAGE 5 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of all tests specified in group A and group B inspections of MIL-PRF-39014, provided they are listed in this drawing. PPM testing and calc

30、ulation is not applicable. 4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2d). TABLE I. Electrical characteristics. DSCC drawing 87122- Capacitance Capacitance tolerance DSCC

31、drawing 87122- Capacitance Capacitance tolerance DSCC drawing 87122- Capacitance Capacitance tolerance 01 02 03 04 05 06 07 08 09 10 11 12 13 .001 F .001 F .0012 F .0012 F .0015 F .0015 F .0018 F .0018 F .0022 F .0022 F .0027 F .0027 F .0033 F K M K M K M K M K M K M K 14 15 16 17 18 19 20 21 22 23

32、24 25 26 .0033 F .0039 F .0039 F .0047 F .0047 F .0056 F .0056 F .0068 F .0068 F .0082 F .0082 F .01 F .01 F M K M K M K M K M K M K M 27 28 29 30 31 32 33 34 35 36 37 38 .015 F .015 F .022 F .022 F .033 F .033 F .047 F .047 F .068 F .068 F .1 F .1 F K M K M K M K M K M K M 5. PACKAGING 5.1 Packagin

33、g. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requireme

34、nts. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated pa

35、ckaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Capacitors conforming to this drawing are intended for use when military

36、specifications do not exist and qualified military devices that will perform the required function are not available for original equipment manufacturer application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog

37、 listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Req

38、uirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. d. Whether the manufacturer performs the group B tests or provi

39、des certification of compliance with group B requirements. e. Requirements for notification of change of product to acquiring activity, if applicable. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE

40、 A CODE IDENT NO. 14933 DWG NO. 87122 REV H PAGE 6 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typica

41、l operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter,

42、refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.4 Replaceability. Capacitors covered by this drawing will replace the same commercial device covered by contractor prepared specification or drawing. 6.5 Users of record. Coordination of this document for future revi

43、sions is coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at capacitorfilterdla.mil or if in writing to: Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990,

44、 Columbus OH 43218-3990 or by telephone (614) 692-0561 or DSN 850-0561. 6.6 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be achieved online at capacitorfilterdla.mil or b

45、y contacting Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus OH 43218-3990 or by telephone (614) 692-0561 or DSN 850-0561. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO

46、SIZE A CODE IDENT NO. 14933 DWG NO. 87122 REV H PAGE 7 DSCC drawing PIN 87122- Vendor similar type 1/ Vendor CAGE Vendor name and address 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 SPB11X102KH8 SPB11X102MH8 SPB11X122KH8 SPB11X122

47、MH8 SPB11X152KH8 SPB11X152MH8 SPB11X182KH8 SPB11X182MH8 SPB11X222KH8 SPB11X222MH8 SPB11X272KH8 SPB11X272MH8 SPB11X332KH8 SPB11X332MH8 SPB11X392KH8 SPB11X392MH8 SPB11X472KH8 SPB11X472MH8 SPB11X562KH8 SPB11X562MH8 SPB11X682KH8 SPB11X682MH8 SPB11X822KH8 SPB11X822MH8 SPB11X103KH8 SPB11X103MH8 SPB11X153K

48、H8 SPB11X153MH8 SPB11X223KH8 SPB11X223MH8 SPB11X333KH8 SPB11X333MH8 SPB11X473KH8 SPB11X473MH8 SPB11X683KH8 SPB11X683MH8 SPB11X104KH8 SPB11X104MH8 96095 Olean Advanced Products A Division of AVX Corporation 1695 Seneca Avenue Olean NY 14760-3736 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-