DLA DSCC-DWG-87120 REV H-2009 CAPACITORS CERAMIC SINGLE IN-LINE PACKAGE NETWORK (8 CAPACITOR SECTIONS) CG.pdf

《DLA DSCC-DWG-87120 REV H-2009 CAPACITORS CERAMIC SINGLE IN-LINE PACKAGE NETWORK (8 CAPACITOR SECTIONS) CG.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-87120 REV H-2009 CAPACITORS CERAMIC SINGLE IN-LINE PACKAGE NETWORK (8 CAPACITOR SECTIONS) CG.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LT DESCRIPTION DATE APPROVED A Added suggested source of supply. 10 Jan 90 David E. Moore B Deleted suggested source of supply. 29 Jun 90 David E. Moore C Deleted and added suggested sources of supply. Modified 3.1.2 and figure 1. Added note for standoff. Editorial changes throughout. 24

2、Feb 92 David E. Moore D Changes in accordance with NOR 5910-R016-96 23 May 96 Andrew R. Ernst E Altered maximum length. Added and removed suggested sources of supply. 25 August 99 Kendall A. Cottongim F Removed suggested source of supply. 10 May 00 Kenneth A. Bernier G Editorial changes made through

3、out. 6 October 2004 Kendall A. Cottongim H Changed drawing to source control with approved sources of supply. Added pure tin prohibition paragraph 3.1.3 and manufacturer eligibility paragraph 3.14. Editorial changes. 15 Dec 09 Michael A. Radecki Prepared in accordance with ASME Y14.100 Source Contro

4、l drawing REV STATUS REV H H H H H H H OF PAGES PAGES 1 2 3 4 5 6 7 PMIC N/A PREPARED BY ROBERT E. GRILLOT DESIGN ACTIVITY DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OH 45444-5000 Original date of drawing: 22 December 1987 CHECKED BY HERALDINE JOHNSON TITLE CAPACITORS, CERAMIC, SINGLE IN-LINE PACKAGE,

5、 NETWORK, (8 CAPACITOR SECTIONS) CG APPROVED BY DAVID W. WITHROW SIZE A CODE IDENT. NO. 14933 DWG NO. 87120 REV H PAGE 1 OF 7 AMSC N/A 5910-E450CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo re

6、production or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87120 REV H PAGE 2 1. SCOPE 1.1 Scope. This drawing and MIL-PRF-20 describe the complete requirements for single-in-line packaged multilayer ceramic capa

7、citor networks. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this speci

8、fication or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this specification, whether or not they are lis

9、ted. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract

10、. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-20 - Capacitors, Fixed, Ceramic Dielectric (Temperature Compensating), Established Reliability and Non-Established Reliability, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Electronics and Electrical Component Parts. MIL-STD-

11、1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise note

12、d herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUI

13、REMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-20 and herein (see figure 1). 3.1.1 Leads. Leads shall be as specified on figure 1. 3.1.2 Case. Molded or conformally coated. 3.1.3 Pure tin. The use of pure tin, as an underplate or

14、 final finish is prohibited both internally and externally. Tin content of capacitor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.1.4 Operating temperature range. The operating temperature range shall be -55C

15、to +125C. 87120- XX Drawing number Dash number (see table I) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87120 REV H PAGE 3 NOTES: 1. Dimensions are in inches. 2.

16、Metric equivalents are given for general information only. 3. Standoff shape is optional. The minimum height of the standoff shall be .015 (0.38 mm). 4. Lead spacing .100 .010 (25.4 0.25) noncumulative. FIGURE 1. Case dimensions and configuration. Inches mm Inches mm .002 .003 .004 .010 .012 .015 .0

17、18 0.05 0.08 0.10 0.25 0.30 0.38 0.46 .058 .060 .100 .115 .135 .300 1.000 1.47 1.52 2.54 2.92 3.43 7.62 25.40 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87120 REV

18、 H PAGE 4 3.2 Electrical characteristics. 3.2.1 Rated voltage. The rated voltage shall be 100 V dc at +85C, 50 V dc at +125C. 3.2.2 Dielectric type. CG (0 30ppm/C), in accordance with MIL-PRF-20. 3.2.3 Temperature coefficient and capacitance drift. In accordance with MIL-PRF-20. 3.2.4 Capacitance. S

19、ee table I. Measured in accordance with method 305 of MIL-STD-202, 1 kHz at 1.0 V rms at +25C. 3.2.5 Dissipation factor (+25C). 0.1 percent maximum (measured under the same conditions as capacitance). 3.2.6 Insulation resistance. Measured in accordance with method 302 of MIL-STD-202. At +25C, rated

20、voltage: 100,000 megohms or 1,000 megohms microfarad, whichever is less. 3.2.7 Dielectric withstanding voltage. Capacitors shall withstand a dc test potential of 250 percent of rated voltage for a period of not less than 1 second nor more than 5 seconds at +25C. The charging current shall not exceed

21、 50 milliamperes. 3.2.8 Q factor. 1000 or greater (measured under the same conditions as capacitance). 3.2.9 Capacitance tolerance. J = 5 percent, K = 10 percent. 3.3 Solderability of terminals. In accordance with MIL-PRF-20. 3.4 Vibration. In accordance with method 204 of MIL-STD-202, test conditio

22、n B (10 to 20,000 Hz, 15 gs). 3.5 Shock. In accordance with MIL-PRF-20. 3.6 Immersion cycling. In accordance with MIL-PRF-20. 3.7 Moisture resistance. In accordance with MIL-PRF-20. 3.8 Life. 200 percent of rated voltage applied at +125C for 1,000 hours. 3.9 Thermal shock. In accordance with method

23、107 of MIL-STD-202, test condition B except low temperature is -55C. 3.10 Voltage conditioning. In accordance with MIL-PRF-20, 200 percent of rated voltage. 3.11 Terminal strength. Capacitors shall withstand a steady pull of 5 pounds for 5 seconds in a direction parallel to the leads. 3.12 Marking.

24、Marking shall be in accordance with MIL-STD-1285 except the capacitors shall be marked with the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, and date lot code as a minimum. 3.13 Recycled, recovered, or environmentally preferable materials

25、. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.14 Manufacturer eligibility. To be eligibl

26、e for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-20, MIL-PRF-123, or MIL-PRF-49470 Qualified Products Database for at least one part, or perform the group A and group B inspections specified herein on a sample of parts agreed upon by the manufacturer and D

27、SCC-VA. 3.15 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.16 Workmanship. Capacitors shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. Provided by

28、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87120 REV H PAGE 5 4. VERIFICATION 4.1 Sampling and inspection. Qualification sampling and inspection are not required. 4.2 Confor

29、mance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of all tests specified in group A (ER) and group B inspections of MIL-PRF-20, provided they are listed in this drawing. PPM testing and calculation is not applicable. 4.2.2 Certification. The

30、 acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2d). TABLE I. Electrical characteristics. DSCC drawing 87120- Capacitance Capacitance tolerance DSCC drawing 87120- Capacitance Capacitance tolerance 01

31、 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 10 pF 10 pF 12 pF 12 pF 15 pF 15 pF 18 pF 18 pF 22 pF 22 pF 27 pF 27 pF 33 pF 33 pF 39 pF 39 pF 47 pF 47 pF 56 pF 56 pF 68 pF 68 pF 82 pF 82 pF 100 pF J K J K J K J K J K J K J K J K J K J K J K J K J 26 27 28 29 30 31 32 33 34

32、 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 100 pF 120 pF 120 pF 150 pF 150 pF 180 pF 180 pF 220 pF 220 pF 270 pF 270 pF 330 pF 330 pF 390 pF 390 pF 470 pF 470 pF 560 pF 560 pF 680 pF 680 pF 820 pF 820 pF 1000 pF 1000 pF K J K J K J K J K J K J K J K J K J K J K J K J K 5. PACKAGING 5.1 Packagi

33、ng. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirem

34、ents. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated p

35、ackaging files, CD-ROM products, or by contacting the responsible packaging activity. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87120 REV H PAGE 6 6. NOTES (This

36、 section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Capacitors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function

37、are not available for original equipment manufacturer application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qu

38、alified for listing, this drawing becomes obsolete and will not be used for new design. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance

39、that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. d. Whether the manufacturer performs the group B tests or provides certification of compliance with group B requirements. e. Requirements for notification of chan

40、ge of product to acquiring activity, if applicable. 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typic

41、al operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter,

42、 refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.4 Replaceability. Capacitors covered by this drawing will replace the same commercial device covered by contractor prepared specification or drawing. 6.5 Users of record. Coordination of this document for future rev

43、isions is coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at capacitorfilterdla.mil or if in writing to: Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990

44、, Columbus OH 43218-3990 or by telephone (614) 692-0561 or DSN 850-0561. 6.6 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be achieved online at capacitorfilterdla.mil or

45、by contacting Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus OH 43218-3990 or by telephone (614) 692-0561 or DSN 850-0561. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO

46、 SIZE A CODE IDENT NO. 14933 DWG NO. 87120 REV H PAGE 7 DSCC drawing PIN 87120- Vendor similar type 1/ DSCC drawing PIN 87120- Vendor similar type 1/ Vendor CAGE Vendor name and address 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 N/A SPC11A100KHA N/A SPC11A120KHA N/A S

47、PC11A150KHA N/A SPC11A180KHA SPC11A220JHA SPC11A220KHA SPC11A270JHA SPC11A270KHA SPC11A330JHA SPC11A330KHA SPC11A390JHA SPC11A390KHA SPC11A470JHA SPC11A470KHA SPC11A560JHA SPC11A560KHA SPC11A680JHA SPC11A680KHA SPC11A820JHA SPC11A820KHA SPC11A101JHA 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

48、 43 44 45 46 47 48 49 50 SPC11A101KHA SPC11A121JHA SPC11A121KHA SPC11A151JHA SPC11A151KHA SPC11A181JHA SPC11A181KHA SPC11A221JHA SPC11A221KHA SPC11A271JHA SPC11A271KHA SPC11A331JHA SPC11A331KHA SPC11A391JHA SPC11A391KHA SPC11A471JHA SPC11A471KHA SPC11A561JHA SPC11A561KHA SPC11A681JHA SPC11A681KHA SP

49、C11A821JHA SPC11A821KHA SPC11A102JHA SPC11A102KHA 96095 Olean Advanced Products A Division of AVX Corporation 1695 Seneca Avenue Olean NY 14760-3736 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,