DLA DSCC-DWG-87081 REV G-2007 CAPACITORS CERAMIC MULTILAYER HIGH VOLTAGE X7R 10 000 V DC《多层陶瓷高电压X7R电容器 10000伏DC》.pdf

《DLA DSCC-DWG-87081 REV G-2007 CAPACITORS CERAMIC MULTILAYER HIGH VOLTAGE X7R 10 000 V DC《多层陶瓷高电压X7R电容器 10000伏DC》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-87081 REV G-2007 CAPACITORS CERAMIC MULTILAYER HIGH VOLTAGE X7R 10 000 V DC《多层陶瓷高电压X7R电容器 10000伏DC》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Added suggested sources of supply. 11 May 88 D. Moore B Suggested source of supply, modified 3.2.2, 3.2.6, and 6.1. Editorial changes throughout. 18 Jan 94 D. Moore C Revised sources of supply, made editorial changes, and converted references to MIL-PRF-494

2、67. Moved solderability testing from group A to group B. Updated suggested sources of supply. 10 April 00 Kendall A. Cottongim D Removed suggested source of supply. Added note 4 to figure 1. Added capacitor tolerance note to 3.2.9. 16 January 01 Kendall A. Cottongim E Added suggested source of suppl

3、y. 12 September 01 Kendall A. Cottongim F Added suggested source of supply. 5 February 02 Kendall A. Cottongim G Added CalRamic Technologies as a suggested source of supply. 19 April 2007 Michael A. Radecki Prepared in accordance with ASME-Y14.100 Selected item drawingREV STATUS REV G G G G G G G OF

4、 PAGES PAGES 1 2 3 4 5 6 7 PMIC N/A PREPARED BY ROBERT E. GRILLOT DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH Original date of drawing CHECKED BY HERALDINE JOHNSON TITLE CAPACITORS, CERAMIC, MULTILAYER, HIGH 24 June 1987 APPROVED BY DAVID E. MOORE VOLTAGE, X7R, 10,000 V DC SIZE A CODE IDENT. NO. 14

5、933 DWG NO. 87081 REV G PAGE 1 OF 7 AMSC N/A 5910-E391CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY

6、 CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87081 REV G PAGE 2 1. SCOPE 1.1 Scope. This drawing and MIL-PRF-49467 describe the complete requirements for high voltage multilayer ceramic capacitors. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 87081 -XX | |

7、| | Drawing Dash number number (see table I) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional informat

8、ion or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Spec

9、ifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MI

10、L-PRF-49467 - Capacitor, Fixed, Ceramic, Multilayer, High Voltage (General Purpose), Established Reliability, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Test Methods Standard Electronics and Electrical Component Parts. MIL-STD-1285 - Marking of Electrical and Electronic

11、 Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/www.assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. In the event of a conflict betw

12、een the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface

13、 and physical dimensions shall be as specified in MIL-PRF-49467 and herein (see figure 1). 3.1.1 Leads. Leads shall be solder coated. Tin-lead (Sn-Pb) finishes are acceptable provided that the minimum lead content is 3 percent. 3.1.2 Case. Epoxy, conformally coated. 3.1.3 Operating temperature range

14、. The operating temperature range shall be -55C to +125C. 3.2 Electrical characteristics. 3.2.1 Rated voltage. The rated voltage shall be 10,000 volts dc. 3.2.2 Dielectric type. X7R. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS

15、 SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87081 REV G PAGE 3 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. H dimension includes meniscus. 4. S dimension shall be maintained from chip body to end of leads. FIGURE 1. Case dim

16、ensions and configuration. Case Sizes (max.) Lead spacing code Width (W) Height (H) Thickness (T) .030 (S) A B C 1.050 1.250 1.450 .500 .600 .720 .270 .270 .270 .900 1.100 1.300 Inches mm Inches mm .002 .025 .030 .270 .500 .600 .720 0.05 0.64 0.76 6.86 12.70 15.24 18.29 .900 1.050 1.100 1.250 1.300

17、1.450 22.86 26.67 27.94 31.75 33.02 36.83 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87081 REV G PAGE 4 3.2.3 Temperature coefficient. 15 percent. (For MIL-PRF-49

18、467 group B voltage temperature limits use step a through step d only.) 3.2.4 Capacitance. See table I. Measured in accordance with method 305 of MIL-STD-202, 1 kHz at 1.0 V rms at +25C. 3.2.5 Dissipation factor (+25C). 2.5 percent maximum (measured under the same conditions as capacitance). 3.2.6 I

19、nsulation resistance. Measured in accordance with method 302 of MIL-STD-202. At +25C, 500 V dc: 100,000 megohms or 1,000 megohms microfarad, whichever is less. At +125C, 500 V dc: 10,000 megohms or 100 megohms microfarad, whichever is less. 3.2.7 Dielectric withstanding voltage. 1.2 times rated volt

20、age. 3.2.8 Aging rate. -2.0 percent maximum per decade-hour. 3.2.9 Capacitance tolerance. K = 10 percent, M = 20 percent. K tolerance parts may be substituted for M tolerance parts, with procuring activity approval. 3.3 Solderability of terminals. In accordance with MIL-PRF-49467. 3.4 Vibration. In

21、accordance with MIL-PRF-49467. 3.5 Shock. In accordance with MIL-PRF-49467. 3.6 Immersion cycling. In accordance with MIL-PRF-49467. 3.7 Moisture resistance. In accordance with MIL-PRF-49467. 3.8 Life. One hundred percent of rated voltage applied at +125C for 1,000 hours. Resistors with a high value

22、 such as 1 megohm may be used in series with each part under test in lieu of fuses. 3.9 Thermal shock. Method 107, MIL-STD-202, test condition B except low temperature is -55C. 3.10 Voltage conditioning. In accordance with MIL-PRF-49467, 100 percent of rated voltage. Resistors with a high value such

23、 as 1 megohm may be used in series with each part under test in lieu of fuses. 3.11 Terminal strength. In accordance with MIL-PRF-49467. 3.12 Marking. Marking shall be in accordance with MIL-STD-1285 except the capacitors shall be marked with the PIN as specified in 1.2, the manufacturers name or Co

24、mmercial and Government Entity (CAGE) code, and date lot code as a minimum. 3.13 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the op

25、erational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.14 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.15 Workmanship. Capacitors shall be uniform in quality an

26、d free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance inspection. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE

27、ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87081 REV G PAGE 5 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of all tests specified in group A and group B inspections of MIL-PRF-49467, provided they are listed in this drawin

28、g. PPM testing and calculation is not applicable. Solderability testing shall be performed as a separate subgroup of group B inspection with a sample size of 3 units and 0 defectives permitted. 4.2.2 Certification. The procuring activity, at its discretion, may accept a certificate of compliance wit

29、h group B requirements in lieu of performing group B tests (see 6.2d). TABLE I. Electrical characteristics DSCC drawing 87081- Capacitance Capacitance tolerance Case code DSCC drawing 87081- Capacitance Capacitance tolerance Case code 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 470 pF 470 pF

30、560 pF 560 pF 680 pF 680 pF 820 pF 820 pF 1000 pF 1000 pF 1200 pF 1200 pF 1500 pF 1500 pF 1800 pF 1800 pF 2200 pF K M K M K M K M K M K M K M K M K A A A A A A A A A A A A A A A A A 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 2200 pF 2700 pF 2700 pF 3300 pF 3300 pF 3900 pF 3900 pF 4700 pF 470

31、0 pF 5600 pF 5600 pF 6800 pF 6800 pF 8200 pF 8200 pF .01 F .01 F M K M K M K M K M K M K M K M K M A A A A A B B B B C C C C C C C C 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel i

32、s to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency,

33、 or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general

34、or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Capacitors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for original equipment ma

35、nufacturer application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes o

36、bsolete and will not be used for new design. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspecti

37、on with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. d. Whether the manufacturer performs the group B tests or provides certification of compliance with group B requirements. Provided by IHSNot for ResaleNo reproduction or networking permitted without licens

38、e from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87081 REV G PAGE 6 e. Requirements for notification of change of product to procuring activity, if applicable. 6.3 Replaceability. Capacitors covered by this drawing will replace the same commercial dev

39、ice covered by contractor prepared specification or drawing. 6.4 Users of record. Coordination of this document for future revisions are coordinated only with the suggested sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be i

40、n writing to: Defense Supply Center, Columbus, ATTN: DSCC/VAT, Post Office Box 3990, Columbus, OH 43218-3990 or e-mailed to capacitorfilterdscc.dla.mil also by telephone (614) 692-4709 or DSN 850-4709. 6.5 Suggested sources of supply. Suggested sources of supply are listed herein. Additional sources

41、 will be added as they become available. For assistance in the use of this drawing, contact Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or e-mailed to capacitorfilterdscc.dla.mil also by telephone (614) 692-4709 or DSN 850-4709. 1/ DSCC drawing PIN

42、87081- Vendor A similar vendor type Vendor B similar vendor type Vendor C similar vendor type Vendor D similar vendor type Vendor E similar vendor type Vendor F similar vendor type 01 SV10RC471KHA 8840CX471KA103 PCI1561-01 9040B471K103LEXH HQHBR471KB 100HV14B471KM02 SV10RC471MHA 8840CX471MA103 PCI15

43、61-02 9040B471M103LEXH HQHBR471MB 100HV14B471MM03 SV10RC561KHA 8840CX561KA103 PCI1561-03 9040B561K103LEXH HQHBR561KB 100HV14B561KM04 SV10RC561MHA 8840CX561MA103 PCI1561-04 9040B561M103LEXH HQHBR561MB 100HV14B561MM05 SV10RC681KHA 8840CX681KA103 PCI1561-05 9040B681K103LEXH HQHBR681KB 100HV14B681KM06 S

44、V10RC681MHA 8840CX681MA103 PCI1561-06 9040B681M103LEXH HQHBR681MB 100HV14B681MM07 SV10RC821KHA 8840CX821KA103 PCI1561-07 9040B821K103LEXH HQHBR821KB 100HV14B821KM08 SV10RC821MHA 8840CX821MA103 PCI1561-08 9040B821M103LEXH HQHBR821MB 100HV14B821MM09 SV10RC102KHA 8840CX102KA103 PCI1561-09 9040B102K103L

45、EXH HQHBR102KB 100HV14B102KM10 SV10RC102MHA 8840CX102MA103 PCI1561-10 9040B102M103LEXH HQHBR102MB 100HV14B102MM11 SV10RC122KHA 8840CX122KA103 PCI1561-11 9040B122K103LEXH HQHBR122KB 100HV14B122KM12 SV10RC122MHA 8840CX122MA103 PCI1561-12 9040B122M103LEXH HQHBR122MB 100HV14B122MM13 SV10RC152KHA 8840CX1

46、52KA103 PCI1561-13 9040B152K103LEXH HQHBR152KB 100HV14B152KM14 SV10RC152MHA 8840CX152MA103 PCI1561-14 9040B152M103LEXH HQHBR152MB 100HV14B152MM15 SV10RC182KHA 8840CX182KA103 PCI1561-15 9040B182K103LEXH HQHBR182KB 100HV14B182KM16 SV10RC182MHA 8840CX182MA103 PCI1561-16 9040B182M103LEXH HQHBR182MB 100H

47、V14B182MM17 SV10RC222KHA 8840CX222KA103 PCI1561-17 9040B222K103LEXH HQHBR222KB 100HV14B222KM18 SV10RC222MHA 8840CX222MA103 PCI1561-18 9040B222M103LEXH HQHBR222MB 100HV14B222MM19 SV10RC272KHA 8840CX272KA103 PCI1561-19 9040B272K103LEXH HQHBR272KB 100HV14B272KM20 SV10RC272MHA 8840CX272MA103 PCI1561-20

48、9040B272M103LEXH HQHBR272MB 100HV14B272MM21 SV10RC332KHA 8840CX332KA103 PCI1561-21 9040B332K103LEXH HQHBR332KB 100HV14B332KM22 SV10RC332MHA 8840CX332MA103 PCI1561-22 9040B332M103LEXH HQHBR332MB 100HV14B332MM23 SV11RC392KHA 11050CX392KA103 PCI1561-23 11050B392K103LEXH HQJBR392KB 100HV15B392KM24 SV11R

49、C392MHA 11050CX392MA103 PCI1561-24 11050B392M103LEXH HQJBR392MB 100HV15B392MM25 SV11RC472KHA 11050CX472KA103 PCI1561-25 11050B472K103LEXH HQJBR472KB 100HV15B472KM26 SV11RC472MHA 11050CX472MA103 PCI1561-26 11050B472M103LEXH HQJBR472MB 100HV15B472MM27 SV12RC562KHA 13060CX562KA103 PCI1561-27 13060B562K103LEXH HQKBR562KB 100HV16B562KM28 SV12RC562MHA 13060CX562MA103 PCI1561-