DLA DSCC-DWG-06003 REV B-2013 RESISTOR CHIP FIXED POWER METAL STRIP SURFACE MOUNT LOW VALUE (2 WATT) STYLE 4527.pdf

《DLA DSCC-DWG-06003 REV B-2013 RESISTOR CHIP FIXED POWER METAL STRIP SURFACE MOUNT LOW VALUE (2 WATT) STYLE 4527.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-06003 REV B-2013 RESISTOR CHIP FIXED POWER METAL STRIP SURFACE MOUNT LOW VALUE (2 WATT) STYLE 4527.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add short time overload requirements. Editorial changes throughout. 7 APR 06 M. Radecki B Add test requirements to the PIN and new table, manufacturing eligibility paragraph and new vendor plant. Editorial changes throughout. 19 DEC 13 M. Radecki Prepared i

2、n accordance with ASME Y14.100 REV STATUS OF PAGES REV B B B B B B PAGES 1 2 3 4 5 6 PMIC N/A PREPARED BY Andrew R. Ernst DESIGN ACTIVITY: DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO Original date of drawing 28 February 2006 CHECKED BY Andrew R. Ernst TITLE RESISTOR, CHIP, FIXED, POWER METAL STRI

3、P, SURFACE MOUNT, LOW VALUE (2 WATT), STYLE 4527 APPROVED BY Michael A. Radecki SIZE A CODE IDENT. NO. 037Z3 DWG NO. 06003 REV B PAGE 1 OF 6 AMSC N/A 5905-2014-E01 . CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Provided by IHSNot for R

4、esaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO: 06003 REV B PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a .455 X .275, 2 watt, fixed, power metal strip, surface mou

5、nted resistor. * 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 06003 - * * * I I I I I I I I Drawing Resistance value Tolerance Testing number (see 3.3.1, 3.3.2) (see 3.3.3) requirements (see 3.3.6) 2. APPLICABLE DOCUMENTS * 2.1 General. The documents listed in this section a

6、re specified in sections 3, 4 and 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are caut

7、ioned that they must meet all specified requirements of documents in sections 3, 4 and 5 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this documen

8、t to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-55342 - Resistors, Chip, Fixed, Film, Nonestablished Reliability, Established Reliability, Space Level, General Sp

9、ecification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-690 - Failure Rate Sampling Plans and Procedures. MIL-STD-790 - Established Reliability and High Reliability Qualified Products List (QPL) Systems for Electrical, Electronic, and Fiber Optic Parts Specifications. * (Copies of these documents a

10、re available online at http:/quicksearch.dla.mil or from the DLA Document Services, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) * 2.3 Order of precedence. Unless otherwise noted herein or in the contract, or in the event of a conflict between the text of this document and the refe

11、rences cited herein (except for related specification sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requireme

12、nts shall be in accordance with MIL-PRF-55342, and as specified herein. 3.2 Interface and physical dimensions. Resistors shall meet the interface and physical dimensions as specified herein (see figure 1). 3.3 Electrical characteristics. 3.3.1 Resistance. The nominal resistance is expressed in ohms

13、and is identified by five digits. The Letter “R” is substituted for one of the significant digits to represent the decimal point. Resistance values from the standard resistance value table in MIL-PRF-55342 for 0.1 percent and 1.0 percent values shall be used. 3.3.2 Resistance range. The resistance r

14、ange shall be 0.01 ohms to 1.0 ohm (see 6.5). 3.3.3 Resistance tolerance. Resistance tolerances are available in (D) 0.5 percent and (F) 1 percent (see 6.5). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH

15、IO SIZE A CODE IDENT NO. 037Z3 DWG NO: 06003 REV B PAGE 3 Dimensions L H T W W1 0.455 0.032 (11.56 0.813) 0.095 0.005 (2.41 0.127) 0.100 0.010 (2.54 0.254) 0.275 0.005 (6.98 0.127) 0.215 0.005 (5.46 0.127) NOTES: 1. Dimensions are in inches, millimeters are shown in parentheses. 2. Millimeter equiva

16、lents are given for general information only. FIGURE 1. Resistor, fixed, power metal strip, surface mount. 3.3.4 Power rating. The power rating shall be 2 watt at +70C. For operation at temperatures greater than +70C, derate in accordance with figure 2. 3.3.5 Resistance temperature coefficient. The

17、resistance temperature coefficient shall be 75 ppm. * 3.3.6 Testing requirements. The requirement for testing shall be identified by a single letter in accordance with table I. TABLE I. Testing. Symbol Testing requirements (blank) Group A A Group A and Group B B Group A and Power moisture C Group A,

18、 Group B and Power moisture NOTE: Any testing requirements that are not specified in the PIN shall have a certificate of compliance issued (see 4.4.2). 3.4 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of resistor components

19、 and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG

20、 NO: 06003 REV B PAGE 4 FIGURE 2. Derating curves for high ambient temperatures. * 3.5 Power moisture resistance. When resistors are tested as specified in 4.5, there shall be no evidence of mechanical damage; the change in resistance between the initial and final measurements shall not exceed (0.5

21、percent+ 0.0005 ohm). 3.6 Solder mounting integrity. When resistors are tested as specified in 4.6 there shall be no evidence of mechanical damage. Force applied shall be 1.8 kilograms. 3.7 Short time overload. When resistors are tested as specified in 4.7, there shall be no evidence of arcing, burn

22、ing, or charring, the change in resistance between the initial and final measurement shall not exceed (2.0 percent+ 0.0005 ohm). 3.8 Manufacturers performance data. The manufacturers technical specifications and performance data shall be made available to the customer for a period of two years. 3.9

23、Marking. Marking shall be as shown: 06003 (DSCC drawing number) 1R000F (value and tolerance) XXXXX (CAGE code) 3.10 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that t

24、he material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. * 3.11 Manufacturer eligibility. To be eligible for listing as a approved source of supply, a manufacturer shall be listed on the MIL-PRF-55342 Qualified Products List

25、for at least one part, or perform the group A and group B inspections specified herein on a sample agreed upon by the manufacturer and DLA Land and Maritime-VAT. * 3.11.1 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be listed as an approve

26、d source of supply. 3.12 Workmanship. The resistor shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, O

27、HIO SIZE A CODE IDENT NO. 037Z3 DWG NO: 06003 REV B PAGE 5 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not applicable to this document. 4.2 Reliability assurance program. The reliability assurance program specified in MIL-PRF-55342 and maintained in accordance with MIL-

28、STD-790 is not applicable to this document. 4.3 Failure rate qualification. Failure rate qualification specified in MIL-PRF-55342 and MIL-STD-690 is not applicable to this document. 4.4 Conformance inspection. * 4.4.1 Inspection of product for delivery. Inspection of product for delivery shall consi

29、st of group A inspection (ER level only, subgroup 2 (DC resistance only), and subgroup 5 the following exception shall apply: Resistors shall be inspected without addition of any coatings to the laser-marked surface area. Resistors shall be examined for legibility under normal production room lighti

30、ng by an inspector at 10X magnification, and ppm reporting is not applicable) and group B inspection of MIL-PRF-55342. Additionally; a power moisture resistance test as specified in 4.5 shall be performed when specified in the PIN. * 4.4.2 Certification. The manufacturer shall submit a certificate o

31、f compliance in lieu of the group B inspection and/or the power moisture resistance test, if not order in the PIN. * 4.5 Power moisture resistance. Resistors shall be tested in accordance with MIL-PRF-55342. The following details and exceptions shall apply: a. The test is to be performed on an annua

32、l basis. b. A 30 piece sample shall be used with 0 defects allowed. 4.6 Solder mount integrity. Resistors shall be tested as specified in MIL-PRF-55342 and the following exceptions shall apply. Force applied 1.8 kilograms. 4.7 Short time overload. Resistors shall be tested in accordance with MIL-PRF

33、-55342. The following details and exceptions shall apply: a. An overload dc test potential which will result in 5 times the rated wattage. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of mate

34、riel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense

35、Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a g

36、eneral or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Surface mount resistors are used in electronic circuits where space is a major concern. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirement

37、s for delivery; One copy of the conformance inspection data or certification of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. 6.3 Tin whisker growth. The use of alloys with tin content greater than

38、 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surfac

39、e will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). Provided by IHSNot for ResaleNo reproduc

40、tion or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO: 06003 REV B PAGE 6 * 6.4 User of record. Coordination of this document for future revisions is coordinated only with the approved source of supply and the user

41、s of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at resistordla.mil or in writing to: DLA Land and Maritime, Attn: VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. * 6.5 Approved source of s

42、upply. Approved source of supply is listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be obtained online at resistordla.mil or contact DLA Land and Maritime, Attn: VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (61

43、4) 692-0552 or DSN 850-0552. DLA Land and Maritime drawing PIN Vendors similar designation or type number 1/ Vendor CAGE Vendors name and address 06003 WSR-2-ARO 91637 Vishay Dale Electronics PO Box 609 Columbus, NE 68602-0609 06003 WSR-2-ARO SH903 Vishay Dale Electronics #3 Hakotser Street PO Box 2317 Beer Sheva, Israel 84874 1/ Parts must be purchased to the DLA Land and Maritime PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-