DLA DESC-DWG-85034 REV D-2011 HOLDER ELECTRICAL CARD METAL CARD GUIDE.pdf

《DLA DESC-DWG-85034 REV D-2011 HOLDER ELECTRICAL CARD METAL CARD GUIDE.pdf》由会员分享，可在线阅读，更多相关《DLA DESC-DWG-85034 REV D-2011 HOLDER ELECTRICAL CARD METAL CARD GUIDE.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、REVISIONS LTR DESCRIPTION DATE APPROVED A Pages 3, 4, 5, and 6: Changed dimensions. Page 10: Changed paragraph order and wording of workmanship paragraph. Editorial changes throughout. 27 MAR 1987 Ivan Jones B Changed end view tolerance on configurations A and B of figure 1. Changed tolerance on dim

2、ension B of table I for dash numbers 49 through 74. Editorial changes throughout. 23 NOV 1987 Randy Larson C Replaced canceled documents, changed title and corrected FSC. Editorial changes throughout. 8 AUG 2001 Thomas Hess D Added a new source of supply and replaced canceled documents. Editorial ch

3、anges throughout. 14 FEB 2011 David Corbett Prepared in accordance with ASME Y14.100 Source controlled drawing REV PAGE REV STATUS OF PAGES REV D D D D D D D D D D D PAGE 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 Dan McGrath

4、Original date of drawing 11 June 1985 CHECKED BY TITLE Randy Larson HOLDER, ELECTRICAL CARD, METAL, CARD GUIDE APPROVED BY Ivan R. Jones SIZE CAGE CODE DWG. NO. 85034 A 14933 REV D PAGE 1 OF 11 AMSC N/A 5998E061 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DLA LAND AND MARITIME C

5、OLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE CAGE CODE DWG NO. A 14933 85034 REV D PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a family of

6、metal card holders for use with printed circuit boards and circuit card assemblies in moderate shock and vibration environments. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 85034 Drawing number 21 Dash number (see table I) 2. APPLICABLE DOCUMENTS 2.1 General. The docu

7、ments listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this li

8、st, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks for

9、m a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). DEPARTMENT OF DEFENSE STANDARDS MILSTD1285 Marking of Electrical and Electronic Parts. (Copies of these documents are availab

10、le online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Philadelphia, PA 191115094.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein.

11、Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM A666 Standard Specification for Annealed or ColdWorked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. (Applicatio

12、n for copies should be addressed to the American Society for Testing and Materials, 100 Barr Harbor Drive, West Coshohocken, PA 194282959.) SAE INTERNATIONAL (SAE) SAE AS 81021 Copper-Beryllium Alloy (Copper Alloy Numbers C17500 and C17510), Strip. SAE AMS 2700 Passivation of Corrosion-Resistant Ste

13、els. (Application for copies should be addressed to the SAE World Headquaters, 400 Commonwealth Drive, Warrendale, PA 15096-0001 or at URL: http:/www.sae.org/) (NonGovernment Standards and other publications are normally available from the organizations which prepare or which distribute the document

14、s. These documents also may be available in or through libraries or other informational services.) 2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes

15、precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE CAGE CODE

16、 DWG NO. A 14933 85034 REV D PAGE 3 3. REQUIREMENTS 3.1 Interface and physical dimensions. See table I and figure 1. 3.2 Materials. For PINs 01 through 12, 25 through 36, and 49 through 60, the material shall be .016 inch (0.4064 mm) thick stainless steel, type 301, condition H, in accordance with A

17、STM A666 or equivalent. For PINs 13 through 24, 37 through 48, and 61 through 74, the material shall be .016 inch thick beryllium copper (copper alloy number C17500), temper “AT“ in accordance with SAE AS81021. 3.3 Finish. All corrosion resistant steel devices shall be passivate in accordance with S

18、AE AMS 2700. Beryllium copper devices shall have no finish applied. 3.4 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.5 Marking. Marking of the DESC PIN is not required on the card guide however, each unit

19、 package shall be marked in accordance with MILSTD1285 and include the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, and date lot codes. 3.6 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmenta

20、lly preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.7 Workmanship. Retainers shall be processed in such a manner as to be uniform in

21、 quality and shall be free from surface and finish flaws that could affect life or serviceability. Burrs, chipping, and cracking are unacceptable. 4. VERIFICATION 4.1 Sampling and inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performa

22、nce of all inspection requirements as specified herein. Except as otherwise specified in the contract, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves th

23、e right to perform any of the inspections set forth in this drawing where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.2 Conformance inspections. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist

24、of visual and mechanical inspections of interface and physical dimensions (see 3.1), materials (see 3.2), and workmanship (see 3.7). Criteria for defects are listed in 4.2.5. 4.2.2 Optional statement of compliance. The acquiring activity, at its discretion, may accept a statement of compliance in li

25、eu of the manufacturer performing the inspection of product for delivery (see 6.2.b). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE CAGE CODE DWG NO. A 14933 85034 REV D PAGE 4 TABLE I. Dash n

26、umbers and dimensions. PIN Dimension “L“ 0.02 Dimension “A“ +.00 .03 Dimension “B“ +.015 .000 Dimension “C“ Dimension “D“ Card thickness Configuration 01 2.25 .045 .075 .125 .100 .0625 A 02 2.25 .075 .105 125 .100 .0937 03 3.25 .045 .075 .125 .100 .0625 04 3.25 .075 .105 .125 .100 .0937 05 4.25 .045

27、 .075 .125 .100 .0625 06 4.25 .075 .105 .125 .100 .0937 07 5.25 .045 .075 .125 .100 .0625 08 5.25 .075 .105 .125 .100 .0937 09 6.25 .045 .075 .125 .100 .0625 10 6.25 .075 .105 .125 .100 .0937 11 8.25 .045 .075 .125 .100 .0625 12 8.25 .075 .105 .125 .100 .0937 13 2.25 .045 .075 .165 .140 .0625 14 2.2

28、5 .075 .105 .165 .140 .0937 15 3.25 .045 .075 .165 .140 .0625 16 3.25 .075 .105 .165 .140 .0937 17 4.25 .045 .075 .165 .140 .0625 18 4.25 .075 .105 .165 .140 .0937 19 5.25 .045 .075 .165 .140 .0625 20 5.25 .075 .105 .165 .140 .0937 21 6.25 .045 .075 .165 .140 .0625 22 6.25 .075 .105 .165 .140 .0937

29、23 8.25 .045 .075 .165 .140 .0625 24 8.25 .075 .105 .165 .140 .0937 25 2.25 .045 .075 .125 .100 .0625 B 26 2.25 .075 .105 .125 .100 .0937 27 3.25 .045 .075 .125 .100 .0625 28 3.25 .075 .105 .125 .100 .0937 29 4.25 .045 .075 .125 .100 .0625 30 4.25 .075 .105 .125 .100 .0937 31 5.25 .045 .075 .125 .10

30、0 .0625 32 5.25 .075 .105 .125 .100 .0937 33 6.25 .045 .075 .125 .100 .0625 34 6.25 .075 .105 .125 .100 .0937 35 8.25 .045 .075 .125 .100 .0625 36 8.25 .075 .105 .125 .100 .0937 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPP

31、LY CENTER DAYTON, OH 45444 SIZE CAGE CODE DWG NO. A 14933 85034 REV D PAGE 5 TABLE I. Dash numbers and dimensions Continued. PIN Dimension “L“ 0.02 Dimension “A“ +.00 .03 Dimension “B“ +.015 .000 Dimension “C“ Dimension “D“ Card thickness Configuration 37 2.25 .045 .075 .165 .140 .0625 B 38 2.25 .07

32、5 .105 .165 .140 .0937 39 3.25 .045 .075 .165 .140 .0625 40 3.25 .075 .105 .165 .140 .0937 41 4.25 .045 .075 .165 .140 .0625 42 4.25 .075 .105 .165 .140 .0937 43 5.25 .045 .075 .165 .140 .0625 44 5.25 .075 .105 .165 .140 .0937 45 6.25 .045 .075 .165 .140 .0625 46 6.25 .075 .105 .165 .140 .0937 47 8.

33、25 .045 .075 .165 .140 .0625 48 8.25 .075 .105 .165 .140 .0937 49 2.25 .155 .095 .125 .100 .0625 C 50 2.25 .125 .065 125 .100 .0937 51 3.25 .155 .095 .125 .100 .0625 52 3.25 .125 .065 .125 .100 .0937 53 5.25 .155 .095 .125 .100 .0625 54 5.25 .125 .065 .125 .100 .0937 55 2.25 .155 .095 .125 .100 .062

34、5 D 56 2.25 .125 .065 .125 .100 .0937 57 3.25 .155 .095 .125 .100 .0625 58 3.25 .125 .065 .125 .100 .0937 59 5.25 .155 .095 .125 .100 .0625 60 5.25 .125 .065 .125 .100 .0937 61 2.25 .155 .095 .165 .140 .0625 C 62 2.25 .125 .065 .165 .140 .0937 63 3.25 .155 .095 .165 .140 .0625 64 3.25 .125 .065 .165

35、 .140 .0937 65 5.25 .155 .095 .165 .140 .0625 66 5.25 .125 .065 .165 .140 .0937 67 2.25 .155 .095 .165 .140 .0625 D 68 2.25 .125 .065 .165 .140 .0937 69 3.25 .155 .095 .165 .140 .0625 70 3.25 .125 .065 .165 .140 .0937 71 5.25 .155 .095 .165 .140 .0625 72 5.25 .125 .065 .165 .140 .0937 73 6.25 .155 .

36、095 .125 .100 .0625 C 74 6.25 .155 .095 .125 .100 .0625 D Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE CAGE CODE DWG NO. A 14933 85034 REV D PAGE 6 Configuration A Configuration B Configurati

37、on C FIGURE 1. Design and dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE CAGE CODE DWG NO. A 14933 85034 REV D PAGE 7 Configuration D Inches mm Inches mm .002 .005 .015 .020 .025 .0

38、3 .096 .125 .145 0.05 0.13 0.51 0.64 0.51 0.8 2.44 3.18 3.68 .165 .170 .256 .265. .28 .322 .72 .750 1.000 4.19 4.32 6.50 6.73 7.1 8.18 18.3 19.05 25.40 NOTES: 1. Dimensions are in inches. Metric equivalents are given for general information only. 2. Unless otherwise specified, tolerances are for .02

39、 inch (0.5 mm) for two place decimals and .010 (0.25 mm) for three place decimals. FIGURE 1. Design and dimensions Continued. 4.2.3 Sampling plan. A sample of parts shall be randomly selected in accordance with table II, normal sampling. If one or more defects are found, the lot shall be rejected. C

40、riteria for defects are listed in 4.2.5. 4.2.4 Rejected lots. If an inspection lot is rejected after normal sampling inspection, the manufacturer may rework it to correct the defects, or screen out the defective parts and resubmit for inspection. Resubmitted lots shall be inspected by selecting a ra

41、ndom sample of parts in accordance with table II, tightened sampling. If one or more defects are found in this sample, the lot shall be rejected and shall not be supplied to this specification. Resubmitted lots which are acceptable shall be clearly identified as reinspected lots. 4.2.5 Defective cha

42、racteristics and properties. Dimensional characteristics are considered defective when out of tolerance. Physical and functional properties are considered defective when outside the specified minimum, maximum, or range as applicable. Workmanship characteristics are considered defective when they wou

43、ld be detrimental to the intended use, performance requirements, or environmental survival of the part. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444 SIZE CAGE CODE DWG NO. A 14933 85034 REV D PAGE

44、 8 TABLE II. Sampling plan. Lot size Normal Tightened 2 to 25 3 5 26 to 60 5 6 51 to 90 6 7 91 to 150 7 11 151 to 280 10 13 281 to 500 11 16 501 to 1,200 15 19 1,201 to 3,200 18 23 3,201 to 10,000 22 29 10,001 to 35,000 29 35 35,0001 and over 29 40 5. PACKAGING 5.1 Packaging. For acquisition purpose

45、s, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirement

46、s are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM prod

47、ucts, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Card holders conforming to this drawing are intended for use when military specifications do not ex

48、ist and qualified military devices that will perform the required function are not available for OEM application. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. 6.3 Users of record. Coordination of this document for future