DLA AN103301 THRU AN103400 REV 3-1986 BOLT - DRILLED HEX HEAD 1 HOLE 500-20.pdf

《DLA AN103301 THRU AN103400 REV 3-1986 BOLT - DRILLED HEX HEAD 1 HOLE 500-20.pdf》由会员分享，可在线阅读，更多相关《DLA AN103301 THRU AN103400 REV 3-1986 BOLT - DRILLED HEX HEAD 1 HOLE 500-20.pdf（1页珍藏版）》请在麦多课文档分享上搜索。

1、8 O Q : AN103301 THRU AN103Ll00 REV 3 53 W 777771i5 0000243 T SECTION THRU THREAD PROFILE L 1.000 1.062 1.125 1.188 1.250 1.312 :$;?i 1.500 1.562 1.625 i .688 1.750 PED. SUP. CLASS. I 5306 K K .,O00 PART NO. L +.o00 . O60 - .O60 AN103306 1.875 .625 a“ AN103307 1.938 .68 AN103308 2.000 .750 1.812 .56

2、2 AN103311 2,188 .938 14 AN103312 2.250 1.000 -1 AN103313 2.575 1.125 .250 AN103314 2.500 1.250 .312 AN103315 2,625 1.375 .315 AN103316 2.750 .1.500 .438 AN10331 2.875 1.625 ,500 AN10331g 3.000 1.750 -CHAMFER 30 M .750 DIA . (OPPOSITE SIDE OPWONAL) PART NO. L AN103319 3.125 AN103320 3.250 AN103321 3

3、.375 AN103322 3.500 AN103324 3.750 AN103325 .875 AN103326 2 .O00 AN103327 4.125. AN103328 4.250 AN103329 4.375 AN103330 4.500 AN103331 4.625 AN103332 4.750 103323 3.625 (i) THREAD TO HEAD. HAXIMUH TWO IMPERFECT THREADS. IC +.O00 - .O60 _ 1 .a75 2.000 2.125 2.250 2 375 2.500 2.625 2.750 2.875 3.000 3

4、.125 3.250 3.375 3.500 - PART NO. L AN10333 4-Sr5 AN103332 5.000 AN103335 5.125 mi03336 5.250 AN103337 5 -375 AN103338 5 -500 AN103320 5.750 AN103341 5.875 AN103342 6.000 AN10334 AN10334: AN103345 AN103346 AN1033 9 5.625 K +.o00 -.o60 3.625 - 3; 4.000 4.125 4.250 4.500 4.625 4.750 4.375 PAR“ NO. . A

5、N103349 AN103350 AN103351 AN103352 AN10335 Wi03352 AN103355 AN103356 YOTK: (a) SHANK SHALL BE STRAICHT WLTHIN .O02 FIR. PER INCH OF BOLT LENGTH. (2) TNE CONCENTRICITY OF THREAD PD IN RELATION TO THE SHANK SHALL-BE WITUIN .O06 FIR. (3) THB CONCENTRICITY OF THE SHANK IN RELATION TO THE WASHER EACE DIA

6、METER AND HEXAGON SHALL BE YITHIN .O23 FIR. UTERIALS: STEEL AMs6322 UPDNESS: ROCKWELL C26 - 32 PIHISR: cADnIun PLATE AMS2400 SUPFACE ROUGHNESS: AS107 MAHUFACTURING SPECIFICATION: AH57452 i) INSPCTIOPI: ALL PARTS SHALL UNDERGO MAGNETIC INSPECTION IN ACCORDAHCE WITH 1182640 BREAK SHARP EDGES .O03 - .O

7、15 UNLESS OTHERWISE SPECIFTED DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED: TOLERENCES; LINEAR DIMENSIONS, i.01D. ANGULAR DIMENSIONS XN INCHES t2. DO NOT USE UNASSIGNED PART NUMBERS. INACTIVE FOR NEW DESIGN AFTER 3 MARCH 1969 N SUPERSEMNO STANOARO. THIS STANDARD YAS DEVELOPED COOPERATIVELY BY TH

8、E ENGINE AND PROPELLER UTILITY PARTS COMMITTEE OF THE SAE. - - - - . ._ - - - - - _- AIR FORCE-NAVY AERONAUTICAL STANDARD ANI03301 P.A. A-Il THRU CUsf. NAVY-AS BOLT - DRILLED iax HEAD, 1 HOLE, -500-20 AN I03400 ARMY - AV Project NO. 5306-1018 THIS DOCUMENT CONTAINS -1- .- PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-