DLA A-A-59505-2000 TAPE GLASS-SETTING RUBBER UNCURED (FOR SEALING GLASS WINDOWS) [Superseded DLA MIL-T-46114 B CANC NOTICE 2 DLA MIL-T-46114 B VALID NOTICE 1 DLA MIL-T-46114 B (1) .pdf

《DLA A-A-59505-2000 TAPE GLASS-SETTING RUBBER UNCURED (FOR SEALING GLASS WINDOWS) [Superseded DLA MIL-T-46114 B CANC NOTICE 2 DLA MIL-T-46114 B VALID NOTICE 1 DLA MIL-T-46114 B (1) .pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59505-2000 TAPE GLASS-SETTING RUBBER UNCURED (FOR SEALING GLASS WINDOWS) [Superseded DLA MIL-T-46114 B CANC NOTICE 2 DLA MIL-T-46114 B VALID NOTICE 1 DLA MIL-T-46114 B (1) .pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUNDA-A-5950529 June 2000 SUPERSEDINGMIL-T-46114B13 July 1978Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any datathat may improve this document should be sent to: Defense Supply Center Richmond(DSCR), ATTN: DSCR-VBD, 8000 Jefferson Davis Highway, Richmo

2、nd, VA 23297-5610.AMSC N/A FSC 9320DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.COMMERCIAL ITEM DESCRIPTIONTAPE, GLASS-SETTING: RUBBER, UNCURED(FOR SEALING GLASS WINDOWS)The General Services Administration has authorized the useof this commercial item description

3、by all federal agencies.1. SCOPE. This commercial item description (CID) covers one type of glass-setting tape,composed of one of three compounds identified herein, used for sealing glass in metal channels.2. SALIENT CHARACTERISTICS2.1 Material Requirements:2.1.1 The material shall be a compound of

4、one of the following, as specified in the acquisitionorder (see 6.2(b):a. Uncured natural rubber and cotton fiberb. Synthetic rubber and cotton fiberc. Uncured natural and synthetic rubbers and cotton fiber2.1.2 The glass-setting tape shall consist of 70 3 percent uncured rubber and 30 3 percentfine

5、ly dispersed cotton fiber evenly distributed throughout.2.1.3 Physical property characteristics. The physical property characteristics shall comply withroom temperature requirements as well as those for after heat aging.2.1.3.1 Room temperature requirements. The room temperature requirements are:a.

6、Durometer hardness (Shore A) shall be 65 with a tolerance of five.b. The minimum tensile strength is 250 PSI.c. Elongation percentage is 15 percent minimum.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-595052d. The swell or dimensional change f

7、rom original shall be 5 percent maximum. Thismay be determined by immersing a sample in distilled water at 23 1.1 C (73.4 2 F) for 48hours 1 hour.2.1.3.2 Requirements for after heat aging. After heat aging requirements are: (The aging periodshall be 48 1 hour at an oven temperature of 70 1 C (158 2

8、F).a. The durometer hardness (Shore A) shall be 65 with a tolerance of five.b. The maximum tensile strength shall be 400 PSI.c. The minimum elongation shall be 24 percent.2.2 Dimensions. The length of roll, and width and thickness of tape shall be as specified in theacquisition order (see 6.2(c). Th

9、e length shall be within one percent, the width within 1/16 of aninch, and the thickness shall be within 0.004 inches of the specified dimensions.2.3 Glass-Setting Tape. The glass-setting tape shall be furnished in rolls. Each roll shall beevenly and neatly wound around its own center without telesc

10、oping and shall be suitablyrestrained from unwinding. The tape shall unroll evenly and uniformly and shall not sticktogether so as to cause injury to the surface. Each roll shall be one continuous strip.2.3.1 Color. The color of the glass-setting tape shall be black.2.3.2 Texture. The texture of the

11、 glass-setting tape shall be uniform.2.3.3 Shelf life. The glass-setting tape shall meet the requirements of this specification whenstored in original containers at moderate temperature (not to exceed 37.8 C (100 F) for sixmonths.3. REGULATORY REQUIREMENTS3.1 Recovered materials. The offeror/contrac

12、tor is encouraged to use recovered materials to themaximum extent practicable, in accordance with paragraph 23.403 of the Federal AcquisitionRegulation (FAR).4. PRODUCT CONFORMANCE PROVISIONS4.1 Product conformance. The products provided shall meet the salient characteristics of thiscommercial item

13、description, conform to the producers own drawings, specifications, standards,and quality assurance practices, and be the same product offered for sale in the commercialmarketplace. The government reserves the right to require proof of such conformance.5. PACKAGING5.1 Preservation, packing, and mark

14、ing. For acquisition purposes, the glass-setting tape shall bepreserved, packed, and marked as specified in the acquisition order (see 6.2(d).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5950536. NOTES6.1 Intended use. The glass setting tape f

15、urnished under this specification is for use as a sealerfor glass (windows) prior to insertion in metal channels (window lifts, vent windows,windshields).6.2 Ordering data. Procurement documents shall specify the following:a. CID document number, revision, and CID PINc. Material compound (see 2.1.1)

16、b. Length, width and thickness of tape (see 2.2)d. Packaging requirements (see 5.1)6.3 Part or identification number (PIN). The part or identification numbering procedure isAA59505-1. It is for government purposes and does not constitute a requirement for thecontractor.6.4 Sources of documents.6.4.1

17、 FAR. The FAR may be obtained from the Superintendent of Documents, U.S.Government Printing Office, Washington, DC 20402-0001.MILITARY INTERESTS:CIVIL AGENCYCOORDINATING ACTIVITY:Custodians:Army - MRNavy - YDAir Force - 99GSA - 7FXEReviewers:Army - AT, MDPreparing activity:DLA - GS(Project 9320-0127)Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-