DLA A-A-55422 A-2007 ADAPTER SWITCH ACTUATOR (FOR MINIATURE BASIC SENSITIVE SWITCHES)《开关执行器(微型基础敏感开关用)转接器》.pdf

《DLA A-A-55422 A-2007 ADAPTER SWITCH ACTUATOR (FOR MINIATURE BASIC SENSITIVE SWITCHES)《开关执行器(微型基础敏感开关用)转接器》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55422 A-2007 ADAPTER SWITCH ACTUATOR (FOR MINIATURE BASIC SENSITIVE SWITCHES)《开关执行器(微型基础敏感开关用)转接器》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5930 INCH- POUND A-A-55422A 1 February 2007 A-A-55422 15 September 1993 COMMERCIAL ITEM DESCRIPTION ADAPTER, SWITCH ACTUATOR (FOR MINIATURE BASIC SENSITIVE SWITCHES) The General Services Administration has authorized the use of this commercial item description for all federal agencies.

2、1. SCOPE: This commercial item description (CID) covers the general requirements for switch actuator miniature basic sensitive switches. Actuators covered by this CID are designed to mate with miniature basic sensitive switches such as MIL-PRF-8805/27 or similar items. 2. CLASSIFICATION /PART OR IDE

3、NTIFICATION NUMBER (PIN). This CID uses a classification system which is included in the PIN as shown in the following example (See 7.1). A-A-55422 - XX CID number Dash number (See table I) 3. SALIENT CHARACTERISTICS. 3.1 Interface and physical dimensions: Actuators supplied to this CID shall be as

4、specified herein (See figure 1). 3.2 Operating characteristics: The operating characteristics shall be as specified in table I. 3.3 Material: All metal parts shall be corrosion resistant or suitable protected to resist corrosion. The roller material shall be oil bronze. Nonmetallic materials shall n

5、ot be used for bracket. 3.4 Marking: Actuators supplied to this CID shall be marked with the manufacturers (MFRs) standard commercial PIN. (NOTE: The part number marked on the unit pack shall be the CID PIN.) 3.5 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or e

6、nvironmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.6 Workmanship: Switch actuator shall be processed in such a manner as

7、 to be uniform in quality and shall be free from other defects that will affect life, serviceability, or appearance. Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any data that may improve this document should be sent to: Defense Supply Center Columbus, ATTN:

8、DSCC-VAT, P. O. Box 3990, Columbus, OH 43218-3990, or email to switchdla.mil. Since contact information can change, you may want to verify the currency of the address information using the ASSIST Online database at http:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networkin

9、g permitted without license from IHS-,-,-A-A-55422A 2TABLE I Operating characteristics 1/ CID PIN Actuator description O. F. max newtons (ounces) R.F. min newtons (ounces) P.T. max mm (inches) O. T. min mm ( Inches) D. T. max mm (inches) A-A-55422-01 Roller leaf 5.00 (18) 1.11 (4) 1.52 (.060) 0.79 (

10、.0310 0.41 (.016) A-A-55422-02 Roller lever 1.39 (5) 0.28 (1) 4.78(.188) 1.57 (.062) 1.98 (.078) 1/ All characteristics are taken with actuator assembled on MIL-PRF-8805/27 basic switch or similar item. Characteristics: O.F Operating force, R.F. Release force, P.T. Pretravel, O.T Over Travel, D. T.

11、Differential travel. mm Inches mm Inches mm Inches mm Inches 0.30 .012 4.83 .19 11.18 .44 20.32 .800 0.64 .025 5.08 .20 14.99 .59 20.57 .81 0.81 .032 5.59 .22 15.88 .625 22.10 .870 1.14 .045 5.84 .23 18.29 .72 22.23 .875 1.48 .055 7.11 .28 19.05 .750 22.63 .891 2.79 .11 10.31 .406 19.46 .766 27.69 1

12、.09 3.56 .14 10.72 .422 FIGURE 1. Configuration and dimensions Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55422A 3NOTES: 1. Dimensions are in millimeters. 2. Unless otherwise specified, tolerance is 0.38 mm (.015) and 2 for angles. 3. The U.

13、S. government preferred system of measurement is the metric SI system. However, since this item was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. 4. Mounting holes will accept p

14、ins or screws of 2.84 mm (.112) maximum diameter. 5. Mounting hardware is furnished with the actuator, unassembled. 6. Operating point dimension is taken at the top of the roller. 7. Switches are not included with actuators. FIGURE 1. Configuration and dimensions Continued. Provided by IHSNot for Re

15、saleNo reproduction or networking permitted without license from IHS-,-,-A-A-55422A 44. REGULATORY REQUIREMENTS: The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFOR

16、MACE PROVISONS. 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The Government rese

17、rves the right to require proof of such conformance. 6. PACKAGING: Preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2 for PIN format example. 7.2 En

18、vironmentally preferable materials: Environmentally preferable materials should be used to the maximum extent possible to meet the requirements of this specification. Table II lists the Environmental Protection Agencys (EPA) top seventeen hazardous materials targeted for major usage reduction. Use o

19、f these materials should be minimized or eliminated unless needed to meet the requirements specified herein (See section 3). TABLE II. EPA top seventeen hazardous materials. Benzene Dichloromethane Tetrachloroethylene Cadmium and Compounds Lead and Compounds Toluene Carbon Tetrachloride Mercury and

20、Compounds 1,1,1 - Trichoroethane Chloroform Methyl Ethyl Ketone Trichloroethylene Chromium and Compounds Methyl Isobutyl Ketone Xylenes Cyanide and Compounds Nickel and Compounds 7.3 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory control, and submission of these actua

21、tors to DSCC under the Military Parts Control Advisory Group (MPCAG) evaluation program, CAGE code 58536 should be used. 7.4 Source of documents. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-8805/27 - Switches, Sensitive, 10 Amperes and Low Level, Unsealed (Copies of these documents are available on

22、line at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094). FEDERAL REGULATIONS FAR - Federal Acquisition Regulations (FAR) (Copies of these documents are available online

23、at http:/www.acquisition.gov/comp/far/index.html or from the U.S. Government Printing Office, 732 North Capital Street, NW, Washington D. C. 20401.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55422A 57.5 Ordering data: The contract or order

24、shall specify the following. a) CID document number and revision and CID PIN. b) Product conformance provisions. c) Packaging requirements. 7.6 Commercial products. As part of the market analysis and research effort, this CID was coordinated with the following manufacturers of commercial products. A

25、t the time of CID preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID. MFRs CAGE MFRs name and address 91929 Honeywell Sensing and Control 11 W. Spring Street Freeport, IL 61032-4353 Technical Assistance Phone 815-235-

26、6847 Fax 815-235-8257 Email: Website: 7.7 Part number (P/N) supersession data. These CID PINs supersede the following MFRs P/Ns as shown. This information is being provided to assist in reducing proliferation in the Government inventory system. TABLE III. P/N supersession data CID PIN MFRs CAGE MF

27、Rs CAGE PIN A-A-55422-01 91929 JV-5 A-A-55422-02 91929 JV-20 7.8 Government users. To acquire information on obtaining these actuators from the Government inventory system, contact Defense Supply Center, Columbus, ATTN: DSCC-VAT, P.O. Box 3990, Columbus, OH 43218-3990, or telephone (614) 692-0551. 7

28、.9 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extensiveness of the changes. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55422A 6MILITARY INTE

29、RESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA FSS/7FXE Custodians: Preparing Activity: DLA CC DLA-C (Project 5930-2007-035) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil/ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-