DLA A-A-55152-1994 CONNECTORS ELECTRICAL IEEE 488 COMPATIBLE RECTANGULAR MINIATURE POLARIZED SHELL PLUG AND RECEPTACLE METRIC SCREW LOCKING HARDWARE《公制螺纹锁紧硬件插头及贮器两极化的外壳微型矩形IEEE488兼.pdf

《DLA A-A-55152-1994 CONNECTORS ELECTRICAL IEEE 488 COMPATIBLE RECTANGULAR MINIATURE POLARIZED SHELL PLUG AND RECEPTACLE METRIC SCREW LOCKING HARDWARE《公制螺纹锁紧硬件插头及贮器两极化的外壳微型矩形IEEE488兼.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55152-1994 CONNECTORS ELECTRICAL IEEE 488 COMPATIBLE RECTANGULAR MINIATURE POLARIZED SHELL PLUG AND RECEPTACLE METRIC SCREW LOCKING HARDWARE《公制螺纹锁紧硬件插头及贮器两极化的外壳微型矩形IEEE488兼.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-55152 = 9999974 OLb3594 40T A-A-55152 15 March 1994 COMMERCIAL ITEM DESCRIPTION CONNECTORS, ELECTRICAL, IEEE 488 COMPATIBLE, RECTANGULAR, MINIATURE, POLARIZED SHELL, PLUG AND RECEPTACLE, METRIC SCREW LOCKING HARDWARE The General Services Administration has authorized the use of this commercial i

2、tem description (CID). Abstract. plug or receptacle, electrical digital interface bus connector. applications that require connectors which conform to the IEEE 488 interface standard. Connector hardware covered by this CID is intended for commercial/industrial applications and may be used in militar

3、y systems where individual environmental and performance requirements can be met. Part or Identifyinq Number (PIN). This CID covers the general requirements for metric screw locking hardware for a polarized shell, This connector hardware can be used in The PIN for the CID shall be as shown in the fo

4、llowing example: A-A-55152 I o1 - I I LI CID number Dash number Sa 1 i ent charact er i st i cs. Design, construction, and dimensions. figure 1 and in accordance with IEEE 488. Design, construction, and dimensions shall be as specified on Connector hardware materials. Metric mounting stud standoff.

5、Metric mounting stud standoff shall be of black oxide coated carbon steel. Operating temperature. The operating temperature range shall be from -4OC to t75“C. The hardware, when assembled and locked to mating connectors, shall exhibit no evidence of Vibration. breaking, cracking, or loosening of par

6、ts when subjected to vibration of 10-55-10 Hz traversed in 1 minute at 1.52 millimeters (.O60 inch) total excursion for 2 hours in each of three mutually perpendicular planes. The hardware, when assembled and locked to mating connectors, shall exhibit no evidence Physical shock. of breaking, crackin

7、g, or loosening of parts when subjected to 50 GIs half-sine wave shock of 11 milliseconds duration, 3 shocks in each direction applied along the three mutually perpendicular planes for a total of 18 shocks. Regulatory requirements. This section is not applicable to this CID. DISTRIBUTION STATEMENT A

8、. Approved for public release; distribution is unlimited. FSC 5935 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55152 A-A-55152 16.51 9999974 0163595 346 yM3.5 x 0.6-6H $ II II II -u 4.19 - 4-40 mm INCH 4-19 ,165 6.50 .256 + 8.61 ,339 16.51 .6

9、50 NOTES: 1. Dimensions are in millimeters. 2. Inch-Pounds equivalents are given for information only. Figure 1. Connector, jackscrew. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55152 9999974 O1b3596 282 e Quality assurance provisions. A-A

10、-55152 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection, examination, and test requirements specified herein. his own or any other facilities suitable for the inspection requirements speci

11、fied herein, unless disapproved by the Government. examinations, or tests set forth in this description where such inspections, examinations, and tests are deemed necessary to assure supplies and services conform to prescribed requirements. Except as otherwise specified in the contract or purchase o

12、rder, the contractor may use The Government reserves the right to perform any of the inspections, Contractor certification statement. The contractor shall certify and maintain objective quality evidence that the product offered meets the requirements of this CID, and that the product conforms to the

13、 producers own drawings, specifications, standards, quality assurances practices, and is the same as the product provided as a bid sample. the first delivery and thereafter as may be otherwise provided for under the provisions of the contract. The Government reserves the right to require proof of su

14、ch conformance prior to Certificate of compliance. A certificate of compliance shall accompany all connector hardware supplied to this CID. Packaging. Preservation, packaging, packing, labeling, and marking. Preservation, packaging, labeling, and marking shall be as specified in the contract or purc

15、hase order. Notes. This section contains relevant information which is useful to buyers, users, and suppliers in the process of acquiring the item, but is not mandatory. Referenced document. Other Publication INSTITUTE OF ELECTRICAL AND ELECTRONICS ENGINEERS (IEEE) IEEE 488 - IEEE Standard Digital I

16、nterface for Programmable Instrumentation. (Applications for copies should be addressed to the Institute of Electrical and Electronics Engineers (IEEE), IEEE Service Center, 445 Hoes Lane, P.O. Box 1331, Piscataway, NJ 08855-1331.) Acquisition documents should specify the following: Ordering data. a

17、. CID document number and revision and CID PIN b. Quality assurance provisions. c. Packaging requirements. Comments. Comments on this CID should be directed to Defense Electronics Supply Center, 1507 Wilmington Pike, ATTN: DESC-EMT, Dayton, OH 45444-5000, or telephone (513) 296-5391. 3 Provided by I

18、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55152 W 9999974 0363597 117 CID PIN A-A-55152- o1 A-A-55152 Vendor commercial Vendor CAGE PIN number 552634-3 00779 Source of supply. they become available. A suggested source of supply is listed in table I. Add

19、itional sources will be added as TABLE I. Suggested source of supply. Vendor CAGE number 00779 Vendor name and address AMP, Incorporated 470 Friendship Road Harr i sburg, PA 171 11 -1203 CIVIL AGENCY COORDINATING ACTIVITY: GSA - 7FXE PREPARING ACTIVITY: DLA-ES (Project 5935-D438) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-