DIN EN 14420-2-2013 Hose fittings with clamp units - Part 2 Hose side parts of hose tail German version EN 14420-2 2013《带夹件的软管配件 第2部分 软管尾部的软管侧面部件 德文版本EN 14420-2-2013》.pdf

《DIN EN 14420-2-2013 Hose fittings with clamp units - Part 2 Hose side parts of hose tail German version EN 14420-2 2013《带夹件的软管配件 第2部分 软管尾部的软管侧面部件 德文版本EN 14420-2-2013》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 14420-2-2013 Hose fittings with clamp units - Part 2 Hose side parts of hose tail German version EN 14420-2 2013《带夹件的软管配件 第2部分 软管尾部的软管侧面部件 德文版本EN 14420-2-2013》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、September 2013 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).I

2、CS 23.040.70!%(u%“2058202www.din.deDDIN EN 14420-2Hose fittings with clamp units Part 2: Hose side parts of hose tail;English version EN 14420-2:2013,English translation of DIN EN 14420-2:2013-09Schlaucharmaturen mit Klemmfassungen Teil 2: Schlauchseitige Stutzenteile;Englische Fassung EN 14420-2:20

3、13,Englische bersetzung von DIN EN 14420-2:2013-09Raccords pour flexibles avec demi-coquille Partie 2: Douilles pour flexibles;Version anglaise EN 14420-2:2013,Traduction anglaise de DIN EN 14420-2:2013-09SupersedesDIN EN 14420-2:2005-05www.beuth.deIn case of doubt, the German-language original shal

4、l be considered authoritative.Document comprises 13 pages 08.13 DIN EN 14420-2:2013-09 2 A comma is used as the decimal marker. National foreword This document (EN 14420-2:2013) has been prepared by Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies” (Secretariat: BSI, Uni

5、ted Kingdom). The responsible German body involved in its preparation was the Normenausschuss Rohrleitungen und Dampfkesselanlagen (Piping and Boiler Plant Standards Committee), Working Committee NA 082-00-02 AA Schlauchkupplungen. Amendments This standard differs from DIN EN 14420-2:2005-05 as foll

6、ows: a) Clause 2 “Normative references” has been updated; b) Clause 3 “Terms and definitions” has been added; c) Subclause 3.2 “Surface finish” has been deleted; d) in Clause 5, the list of materials for hose fittings has been supplemented by aluminium and hastelloy; e) Clause 7 “Type testing and qu

7、ality control” has been added; f) the Bibliography has been revised; g) the standard has been editorially revised. Previous editions DIN 2817-3: 1995-05 DIN EN 14420-2: 2005-05 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14420-2 July 2013 ICS 23.040.70 Supersedes EN 14420-2:2004English Vers

8、ion Hose fittings with clamp units - Part 2: Hose side parts of hose tail Raccords pour flexibles avec demi-coquille - Partie 2: Douilles pour flexibles Schlaucharmaturen mit Klemmfassungen - Teil 2: Schlauchseitige Stutzenteile This European Standard was approved by CEN on 15 May 2013. CEN members

9、are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application t

10、o the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

11、Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lith

12、uania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brusse

13、ls 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14420-2:2013: EEN 14420-2:2013 (E) 2 Contents Page Foreword 3 1 Scope 5 2 Normative references 5 3 Terms and definitions .6 4 Dimensions .6 5 Materials .9 6 Marking 10 7 Type

14、testing and quality control . 10 Bibliography . 11 DIN EN 14420-2:2013-09EN 14420-2:2013 (E) 3 Foreword This document (EN 14420-2:2013) has been prepared by Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies”, the secretariat of which is held by BSI. This European Standard

15、 shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2014, and conflicting national standards shall be withdrawn at the latest by January 2014. Attention is drawn to the possibility that some of the elements of this

16、 document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 14420-2:2004. In comparison to EN 14420-2:2004, the following changes have been made: In Clause 2 the normative references have b

17、een updated. A new Clause 3 “Terms and definitions“ has been added. Subclause 3.2 “Surface finish“ has been deleted. In Clause 5, the list of materials appropriate for use in hose fittings has been supplemented by aluminium and hastelloy. Clause 7 on type testing and quality control has been added.

18、The Bibliography has been reviewed. The standard has been revised editorially. EN 14420, Hose fittings with clamp units consists of the following parts: Part 1: Requirements, types of fixing and connection, designation and testing Part 2: Hose side parts of hose tail Part 3: Clamp units, bolted or p

19、inned Part 4: Flange connections Part 5: Threaded connections Part 6: TW tank truck couplings Part 7: Cam locking couplings Part 8: Symmetrical half coupling (Guillemin system) According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are boun

20、d to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, DIN EN 14420-2:2013-09EN 14420-2:2013 (E) 4 Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg,

21、Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 14420-2:2013-09EN 14420-2:2013 (E) 5 1 Scope This European Standard specifies requirements for the hose tail of hose fittings according to EN 14420-1 for use w

22、ith clamp units according to EN 14420-3. Furthermore, it specifies materials for hose fittings with clamp units according to EN 14420-4 to EN 14420-8. Maximum working pressure is 25 bar1); maximum working temperature is 65 C. 2 Normative references The following documents, in whole or in part, are n

23、ormatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 755-2, Aluminium and aluminium alloys Extruded rod/bar,

24、 tube and profiles Part 2: Mechanical properties EN 1706, Aluminium and aluminium alloys Castings Chemical composition and mechanical properties EN 1982, Copper and copper alloys Ingots and castings EN 10025-2, Hot rolled products of structural steels Part 2: Technical delivery conditions for non-al

25、loy structural steels EN 10087, Free-cutting steels Technical delivery conditions for semi-finished products, hot-rolled bars and rods EN 10088-1, Stainless steels Part 1: List of stainless steels EN 10213, Steel castings for pressure purposes EN 10217-1, Welded steel tubes for pressure purposes Tec

26、hnical delivery conditions Part 1: Non-alloy steel tubes with specified room temperature properties EN 10283, Corrosion resistant steel castings EN 12420, Copper and copper alloys Forgings EN 14420-1:2013, Hose fittings with clamp units Part 1: Requirements, types of fixing and connection, designati

27、on and testing EN 14420-4, Hose fittings with clamp units Part 4: Flange connections EN 14420-5, Hose fittings with clamp units Part 5: Threaded connections EN 14420-6, Hose fittings with clamp units Part 6: TW tank truck couplings EN 14420-7, Hose fittings with clamp units Part 7: Cam locking coupl

28、ings EN 14420-8, Hose fittings with clamp units Part 8: Symmetrical half coupling (Guillemin system) EN ISO 8330:2008, Rubber and plastics hoses and hose assemblies Vocabulary (ISO 8330:2007) 1) 1 bar = 0,1 MPa. DIN EN 14420-2:2013-09EN 14420-2:2013 (E) 6 3 Terms and definitions For the purposes of

29、this document, the terms and definitions given in EN ISO 8330:2008 and the following apply. 3.1 DN (nominal size) alphanumeric designation of size for components of a pipework system, which is used for reference purposes. It comprises the letters DN followed by a dimensionless whole number which is

30、indirectly related to the physical size, in millimetres, of the bore or outside diameter of the end connections Note 1 to entry: The number following the letters DN does not represent a measurable value and should not be used for calculation purposes except where specified in the relevant standard.

31、Note 2 to entry: In those standards which use the DN designation system, any relationship between DN and component dimensions should be given, e.g. DN/OD or DN/ID. SOURCE: EN ISO 6708:1995, 2.1 4 Dimensions Types of fittings shall be chosen by the manufacturer depending on the manufacturing process.

32、 NOTE Details not specified in this document are at the discretion of the manufacturer. Grooves are admissible on the outside surface of tails Type A, Type B or Type C, provided that their outside diameter is not less than d4(see Type B). Serration is admissible on the outside surface of tails of Ty

33、pe A and Type B of nominal size DN 15 to DN 80, whose outside diameter shall not exceed d5(see Type B). For nominal sizes DN 100 to DN 200 serrations are admissible with outside diameter not more than 2,2 mm above d6. Grooves and ribs should be manufactured without sharp edges. DIN EN 14420-2:2013-0

34、9EN 14420-2:2013 (E) 7 Type A DN 15 to DN 200 Type B2)DN 15 to DN 80 Type C DN 100 to DN 150 Inner contour cylindrical or conical at the discretion of the manufacturer. Other dimensions and specifications as type A Figure 1 Hose side parts of hose tail 2) Type B not applicable to clamp unit S accord

35、ing to EN 14420-3. DIN EN 14420-2:2013-09EN 14420-2:2013 (E) 8 Table 1 Dimensions for hose side parts of tail Dimensions in millimetres Nominal size Type Inside diameter of hose d1d2d3d4d5d6d7d8f k l1l2r DN Tolerances 5,00+max. Tolerances Tolerances 04,0Tolerances Tolerances 5,00+05,0min. 5,0 0,5 15

36、 A 13 9 01 12,2 min. 13,4 19 0113 0,1 4 4 42 1,5 20 19 15 18,4 19,4 26 19 25 25 21 24a26,6amax. 25,4 32 25 32 32 28 31a33,6a32,4 39 32 40 B 38 33,5 37,8 0,5 40 08,038,4 45 38 4,5 50 50 45,5 49,5 52 50,4 58 50 4,5 49 51 50,5 53 51,4 65 63 58,5 5,05,1+62,5 65,5 63,4 73 63 5,5 5,5 63 80 75 70,5 74,5 77

37、,4 75,4 85 75 67 76 75,5 78,4 76,4 100 C 100 94 90 94 100,3 110 100 0,2 8 7,5 96 95 101,5 101,8 150 150 140 5,02+131 140 150,1 164 150 13 10 166 144 3 200 200 190 5,05,2+ 200 219 02+200 17 12 230 aAt DN 25 and DN 32 dimensions d4and d5are given as limiting dimensions for grooves and ribs for tails t

38、ype A. DIN EN 14420-2:2013-09EN 14420-2:2013 (E) 9 5 Materials Only materials listed below shall be used each in connection with the individual fittings according to EN 14420-4, EN 14420-5, EN 14420-6, EN 14420-7 and EN 14420-8 which are indicated there: a) Non-alloyed steels S235JRG2 material numbe

39、r 1.0038 according to EN 10025-2 S355J0 (former St52-3U) material number 1.0553 according to EN 10025-2 S355J2G3 (former St52-3N) material number 1.0570 according to EN 10025-2 P235TR1 material number 1.0254 according to EN 10217-1 11 SMnPb 30 material number 1.0718 according to EN 10087 b) Stainles

40、s steels X5CrNi18-10 material number 1.4301 according to EN 10088-1 X5CrNiMo17-12-2 material number 1.4401 according to EN 10088-1 X2CrNiMo17-12-2 material number 1.4404 according to EN 10088-1 X6CrNiTi18-10 material number 1.4541 according to EN 10088-1 X6CrNiMoTi17-12-2 material number 1.4571 acco

41、rding to EN 10088-1 GX5CrNiMo19-11-2 material number 1.4408 according to EN 10213 GX5CrNiMoNb19-11-12 material number 1.4581 according to EN 10213 GX5CrNiMo19-11-2 material number 1.4408 according to EN 10283 c) Copper-zinc alloys CuZn39Pb3 material number CW614N according to EN 12420 CuZn40Pb2 mate

42、rial number CW617N according to EN 12420 GK-CuZn37Pb material number CC754S according to EN 1982 d) Copper-tin alloy CuSn5Zn5Pb5-C material number CC491K according to EN 1982 e) Aluminium Alu forged material number EN AW-6082 according to EN 755-2 Alu bar materials material number EN AW-6060 accordi

43、ng to EN 755-2 Alu cast material number EN AC-47000 according to EN 1706 f) Hastelloy Hastelloy B3 material number 2.4600 Hastelloy C22 material number 2.4602 Hastelloy C4 material number 2.4610 Hastelloy C2 material number 2.4819 DIN EN 14420-2:2013-09EN 14420-2:2013 (E) 10 6 Marking If appropriate

44、 surface area is available, the hose side parts of the hose tail shall be clearly and durably marked with the following information: a) EN 14420-2; b) manufacturers name or trademark; c) type and nominal size; d) material number. 7 Type testing and quality control Type testing and quality control sh

45、all be done according to EN 14420-1:2013, Clause 7. DIN EN 14420-2:2013-09EN 14420-2:2013 (E) 11 Bibliography 1 EN 14420-3, Hose fittings with clamp units Part 3: Clamp units, bolted or pinned 2 EN ISO 6708:1995, Pipework components Definition and selection of DN (nominal size) (ISO 6708:1995) DIN EN 14420-2:2013-09