DIN 935-1-2013 Hexagon slotted and castle nuts - Part 1 Metric coarse and fine pitch thread product grades A and B《六角开槽和槽顶螺母 第1部分 公制粗牙和细牙螺纹 A级和B级产品》.pdf

《DIN 935-1-2013 Hexagon slotted and castle nuts - Part 1 Metric coarse and fine pitch thread product grades A and B《六角开槽和槽顶螺母 第1部分 公制粗牙和细牙螺纹 A级和B级产品》.pdf》由会员分享，可在线阅读，更多相关《DIN 935-1-2013 Hexagon slotted and castle nuts - Part 1 Metric coarse and fine pitch thread product grades A and B《六角开槽和槽顶螺母 第1部分 公制粗牙和细牙螺纹 A级和B级产品》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、August 2013Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 2

2、1.060.20!%+Fd“2083565www.din.deDDIN 935-1Hexagon slotted and castle nuts Part 1: Metric coarse and fine pitch thread, product grades A and B,English translation of DIN 935-1:2013-08Sechskant-Kronenmuttern Teil 1: Metrisches Regel- und Feingewinde, Produktklassen A und B,Englische bersetzung von DIN

3、935-1:2013-08crous hexagonaux crneaux et crneaux dgags Partie 1: Filetage mtrique pas gros et fin, grades A et B,Traduction anglaise de DIN 935-1:2013-08SupersedesDIN 935-1:2000-10www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 12 pages

4、01.14 DIN 935-1:2013-08 2 A comma is used as the decimal marker. Contents Page Foreword . 3 1 Scope . 4 2 Normative references . 4 3 Dimensions 5 4 Technical delivery conditions . 9 5 Designation . 10 6 Masses . 10 7 Marking 11 Bibliography . 12 DIN 935-1:2013-08 3 Foreword This standard has been pr

5、epared by Working Committee NA 067-00-03 AA Verbindungselemente mit metrischem Innengewinde of the Normenausschuss Mechanische Verbindungselemente (FMV) (Fasteners Standards Committee). The DIN 4000-161-1 tabular layout of article characteristics applies to slotted and castle nuts covered in this st

6、andard. DIN 935 consists of the following parts with the general title Hexagon slotted and castle nuts: Part 1: Metric coarse and fine pitch threads, product grades A and B Part 3: Metric coarse pitch threads, product grade C Attention is drawn to the possibility that some of the elements of this do

7、cument may be the subject of patent rights. DIN shall not be held responsible for identifying any or all such patent rights. Amendments This standard differs from DIN 935-1:2000-10 as follows: a) the title of the standard has been defined more precisely by adding “hexagon”; b) normative references h

8、ave been updated; c) in Table 1 all dimensions are now given to the same number of decimal places; d) symbols have been changed from d to D, w to m and m to h in accordance with DIN EN ISO 225; e) technical delivery conditions of Table 2 have been brought into line with DIN EN ISO 898-2; f) Clause 7

9、 “Marking” has been revised. Previous editions DIN Kr 753: 1934-12, 1936-09 DIN 533-1: 1941-01, 1959-09, 1963-06 DIN 534-1: 1941x-01, 1963-06 DIN 935: 1968-05, 1977-04 DIN 935-1: 1926-01, 1934-04, 1937-06, 1942x-04, 1954-02, 1956-05, 1963-06, 1983-12, 1987-10, 2000-02, 2000-10 DIN 935-1:2013-08 4 1

10、Scope This standard specifies hexagon slotted and castle nuts with metric coarse and fine pitch thread and nominal thread diameter from 4 mm to 100 mm of product grade A (up to 16 mm nominal thread diameter) and product grade B (over 16 mm nominal thread diameter). 2 Normative references The followi

11、ng documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. DIN 267-2, Fastene

12、rs Technical delivery conditions Design and dimensional accuracy DIN 962, Bolts, screws, studs and nuts Designations, types and finishes DIN EN 28839, Mechanical properties of fasteners Nonferrous metal bolts, screws, studs and nuts DIN EN ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and

13、 descriptions of dimensions DIN EN ISO 898-2, Mechanical properties of fasteners made of carbon steel and alloy steel Part 2: Nuts with specified property classes Coarse thread and fine pitch thread DIN EN ISO 1234, Split pins DIN EN ISO 3269, Fasteners Acceptance inspection DIN EN ISO 3506-2, Mecha

14、nical properties of corrosion-resistant stainless steel fasteners Part 2: Nuts DIN EN ISO 4042, Fasteners Electroplated coatings DIN EN ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C DIN EN ISO 6157-2, Fasteners Surface discontinuities Part 2: Nu

15、ts DIN EN ISO 10484, Widening test on nuts DIN EN ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings DIN EN ISO 10684, Fasteners Hot dip galvanized coatings DIN ISO 261, ISO general purpose metric screw threads General plan DIN ISO 965-1, ISO general purpose metric screw threads T

16、olerances Part 1: Principles and basic data DIN ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts DIN 935-1:2013-08 5 3 Dimensions Dimensions shall be as given in Figures 1 and 2 and Table 1. Other relevant symbols and their descriptions are specified in DIN EN ISO 225. 2nr

17、= Figure 1 Hexagon slotted nuts and castle nuts with D 10 mm (notation) Other dimensions as in Figure 1 Figure 2 Hexagon slotted nuts and castle nuts D 12 mm (notation) The bottom of slots may be round, rounded or chamfered, at the manufacturers discretion. The slotted nuts may be supplied with or w

18、ithout thread in the castle, at the manufacturers discretion. Faces of the castle may be rounded. Number of slots: D 39 mm: 6 42 mm D 68 mm: 8 D 72 mm: 10 DIN 935-1:2013-08 6 Table 1 Nut dimensions Dimensions in millimetres Thread size M4 M5 M6 (M7) M8 M10 M12 (M14) M16 (M18) M8 1 M10 1 M12 1,5 (M14

19、 1,5) M16 1,5 (M18 1,5) M10 1,25 M12 1,25 (M18 2) Pa0,7 0,8 1 1 1,25 1,5 1,75 2 2 2,5 damax. 4,60 5,75 6,75 7,75 8,75 10,80 13,00 15,10 17,30 19,50 min. 4,00 5,00 6,00 7,00 8,00 10,00 12,00 14,00 16,00 18,00 demax. 16,00 18,00 22,00 25,00 min. 15,57 17,57 21,48 24,30 dwmin. 5,90 6,90 8,90 9,50 11,60

20、 14,60 16,60 19,60 22,50 24,90 e min. 7,66 8,79 11,05 12,12 14,38 17,77 20,03 23,35 26,75 29,56 h Nominal size = max. 5 6 7,5 8 9,5 12 15 16 19 21 min. 4,70 5,70 7,14 7,64 9,14 11,57 14,57 15,57 18,48 20,16 m max. 3,20 4,00 5,00 5,50 6,50 8,00 10,00 11,00 13,00 15,00 min. 2,90 3,70 4,70 5,20 6,14 7,

21、64 9,64 10,57 12,57 14,57 mwmin. 2,30 3,00 3,80 4,20 4,90 6,10 7,70 8,20 9,80 11,20 n max. 1,45 1,65 2,25 2,25 2,75 3,05 3,80 3,80 4,80 4,80 min. 1,20 1,40 2,00 2,00 2,50 2,80 3,50 3,50 4,50 4,50 s Nominal size = max. 7 8 10 11 13 16b18b21b24 27 min. 6,78 7,78 9,78 10,73 12,73 15,73 17,73 20,67 23,6

22、7 26,16 Size of split pin as in DIN EN ISO 1234c1 10 1,2 12 1,6 14 1,6 14 2 16 2,5 20 3,2 22 3,2 25 4 28 4 32 NOTE Bracketed sizes should not be used. aP is the pitch of coarse thread as in DIN ISO 261. bThe width across flats shall be included in the designation (see Clause 5). cThe split pin lengt

23、hs given are for guidance only. DIN 935-1:2013-08 7 Table 1 (continued) Dimensions in millimetresThread size M20 (M22) M24 (M27) M30 (M33) M36 (M39) M42 (M45) M20 2 (M22 1,5) M24 2 (M27 2) M30 2 (M33 2) M36 3 (M39 3) M42 3 (M45 3) M20 1,5 (M22 2) Pa2,5 2,5 3 3 3,5 3,5 4 4 4,5 4,5 damax. 21,60 23,80

24、25,90 29,20 32,40 35,60 38,90 42,10 45,40 48,60 min. 20,00 22,00 24,00 27,00 30,00 33,00 36,00 39,00 42,00 45,00 demax. 28,00 32,00 34,00 38,00 42,00 46,00 50,00 55,00 58,00 62,00 min. 27,30 31,00 33,00 37,00 41,00 45,00 49,00 53,80 56,80 60,80 dwmin. 27,7 31,4 33,2 38,00 42,70 46,60 51,10 55,90 60,

25、60 64,70 e min. 32,95 37,29 39,55 45,20 50,85 55,37 60,79 66,44 71,30 76,95 h Nominal size = max. 22,0 26,0 27,0 30,0 33,0 35,0 38,0 40,0 46,0 48,0 min. 21,16 25,16 26,16 29,16 32,00 34,00 37,00 39,00 45,00 47,00 m max. 16,00 18,00 19,00 22,00 24,00 26,00 29,00 31,00 34,00 36,00 min. 15,57 17,57 18,

26、48 21,48 23,48 25,48 28,48 30,28 33,38 35,38 mwmin. 11,90 13,50 14,20 16,60 18,20 19,80 21,90 23,50 25,90 27,50 n max. 4,80 5,80 5,80 5,80 7,36 7,36 7,36 7,36 9,36 9,36 min. 4,50 5,50 5,50 5,50 7,00 7,00 7,00 7,00 9,00 9,00 s Nominal size = max. 30 34b36 41 46 50 55 60 65 70 min. 29,16 33,00 35,00 4

27、0,00 45,00 49,00 53,80 58,80 63,10 68,10 Size of split pin as in DIN EN ISO 1234c4 36 5 36 5 40 5 45 6,3 506,3 566,3 636,3 718 71 8 80 NOTE Bracketed sizes should not be used. a, b, cFor footnotes see page 6. DIN 935-1:2013-08 8 Table 1 (continued) Dimensions in millimetres Thread size M48 (M52) M56

28、 (M60) M64 (M68) M72 6 (M76 6) M80 6 (M85 6) M90 6 M100 6 M48 3 (M52 3) M56 4 (M60 4) M64 4 (M68 4) M72 4 (M76 4) M80 4 (M85 4) M90 4 M100 4 Pa5 5 5 5 6 6 damax. 51,80 56,20 61,00 64,80 69,10 73,40 77,80 82,10 86,40 91,80 97,20 108,00 min. 48,00 52,00 56,00 60,00 64,00 68,00 72,00 76,00 80,00 85,00

29、90,00 100,00 demax. 65,00 70,00 75,00 80,00 85,00 90,00 95,00 100,00 105,00 110,00 120,00 130,00 min. 63,80 68,80 73,80 78,80 83,60 88,60 93,60 98,60 103,60 108,60 118,00 128,40 dwmin. 69,40 74,20 78,70 83,40 88,20 92,90 97,70 102,40 107,20 111,90 121,10 135,40 e min. 82,60 88,25 93,56 99,21 104,86

30、110,51 116,16 121,81 127,46 133,11 144,08 161,02 h Nominal size = max. 50,0 54,0 57,0 63,0 66,0 69,0 73,0 76,0 79,0 88,0 92,0 100,0 min. 49,00 52,80 55,80 61,80 64,80 67,80 71,8 74,80 77,80 86,60 90,60 98,60 m max. 38,00 42,00 45,00 48,00 51,00 54,00 58,00 61,00 64,00 68,00 72,00 80,00 min. 37,38 41

31、,38 44,38 47,38 50,26 53,26 57,26 60,26 63,26 67,26 71,26 79,26 mwmin. 29,10 32,30 34,70 37,10 39,30 41,70 44,90 47,30 49,70 52,90 56,10 62,50 n max. 9,36 9,36 9,36 11,43 11,43 11,43 11,43 11,43 11,43 14,43 14,43 14,43 min. 9,00 9,00 9,00 11,00 11,00 11,00 11,00 11,00 11,00 14,00 14,00 14,00 s Nomin

32、al size = max. 75 80 85 90 95 100 105 110 115 120 130 145 min. 73,10 78,10 82,80 87,80 92,80 97,80 102,80 107,80 112,80 117,80 127,50 142,50 Size of split pin as in DIN EN ISO 1234c8 80 8 90 8 100 10 100 10 100 10 112 10 112 10 125 10 140 10 140 10 140 10 160 NOTE Bracketed sizes should not be used.

33、 a, cFor footnotes see page 6. DIN 935-1:2013-08 9 4 Technical delivery conditions See Table 2. Table 2 Technical delivery conditions Material Steel Stainless steel Nonferrous metals General requirements Standard DIN ISO 8992 Thread Tolerance class 6HaStandard DIN ISO 261; DIN ISO 965-1 Mechanical p

34、roperties Property classb(material) D 39 mm: subject to agreement D 20 mm: A2-70 20 mm 39 mm: subject to agreement CuZn = copper-zinc-alloydStandard DIN EN ISO 898-2 DIN EN ISO 3506-2 DIN EN 28839 Limit deviations and geometrical tolerances Product grade D 16 mm: A D 16 mm: B Standard DIN EN ISO 475

35、9-1 Surface coating As processed Plain Plain DIN EN ISO 4042 applies with regard to electroplating. DIN EN ISO 4042 applies with regard to electroplating. DIN EN ISO 10683 applies with regard to non-electrolytically applied zinc flake coatings. DIN EN ISO 10684 applies with regard to hot-dip galvani

36、zing. DIN 267-2 applies with regard to surface roughness. Additional requirements and alternative surface conditions or finishing are to be agreed between manufacturer and purchaser. Surface condition DIN EN ISO 10484 applies with regard to limit values for the widening test. DIN EN ISO 6157-2 appli

37、es with regard to limit values for surface discontinuities. Acceptance inspection DIN EN ISO 3269 applies with regard to acceptance inspection. aWhere an electroplated coating as specified in DIN EN ISO 4042 is to be applied, depending on the coating thickness required, it may be necessary, particul

38、arly in the case of tolerance class 6H nuts, to select a larger fundamental deviation than that assigned to the H position. This however, might impair the resistance of the bolt/nut assembly to stripping. bWhere nuts are to be made to comply with other property classes, these shall be selected based

39、 on the relevant standards. cAs a departure from DIN EN ISO 898-2, a minimum hardness of 272 HV 30 will be adequate for fine pitch thread nuts assigned to property classes 8 and 10. dCU2 or CU3, at the manufacturers discretion. DIN 935-1:2013-08 10 5 Designation Designation of a size M8 hexagon cast

40、le nut of property class 8: Castle nut DIN 935 M8 8 The designation of sizes M10, M12, M14 and M22 nuts shall also include the width across flats (SW), e.g. SW18 for M12: Castle nut DIN 935 M12 SW18 8 If product grade A is desired for nominal thread diameter exceeding 16 mm, this shall be added to t

41、he designation, e.g.: Castle nut DIN 935 M20 8 A If castle nuts of nominal thread diameter from 12 mm to 39 mm without a recess below the castle are to be supplied, the symbol KK shall be added to the designation, e.g.: Castle nut DIN 935 M20 KK 8 DIN 962 shall apply with regard to the designation o

42、f designs and types with additional details to be given when ordering. Nuts supplied in accordance with this standard may only be made of free-cutting steel if this is indicated in the designation by including the symbol AU, e.g.: Castle nut DIN 935 M8 6 AU 6 Masses The values of mass given in Table

43、 3 are for guidance only. They apply for nuts made of steel. Table 3 Masses Thread (D) M4 M5 M6 M7 M8 M10 M12 M14 M16 M18 M20 M22 Mass ( = 7,85 kg/dm3) kg per 1 000 units 1,12 2,3 3,16 3,96 7,35 aaa38,9 57,5 75,2 aThread (D) M24 M27 M30 M33 M36 M39 M42 M45 M48 M52 M56 Mass ( = 7,85 kg/dm3) kg per 1

44、000 units 131 192 264 333 447 584 710 860 1 060 1 300 1 500 Thread (D) M60 M64 M68 M72 6 M76 6 M80 6 M85 6 M90 6 M100 6 Mass ( = 7,85 kg/dm3) kg per 1 000 units 1 800 2 150 2 500 2 900 3 300 3 700 4 100 5 450 7 600 aMasses for castle nuts with the new widths across flats are currently not available.

45、 Approximately the same masses may be assumed for nuts with fine pitch thread. DIN 935-1:2013-08 11 7 Marking Castle nuts shall be marked as specified in DIN EN ISO 898-2, DIN EN ISO 3506-2 and DIN EN 28839. Marking of the bearing surface is only permissible when recessed. Castle nuts manufactured by machining shall only be marked subject to agreement. DIN 935-1:2013-08 12 Bibliography DIN 4000-161, Tabular layout of product properties Part 161: Fasteners with internal thread