BS ISO 18902-2013 Imaging materials Processed imaging materials Albums framing and storage materials《成像材料 经处理的成像材料 相册 框架和存储材料》.pdf

《BS ISO 18902-2013 Imaging materials Processed imaging materials Albums framing and storage materials《成像材料 经处理的成像材料 相册 框架和存储材料》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 18902-2013 Imaging materials Processed imaging materials Albums framing and storage materials《成像材料 经处理的成像材料 相册 框架和存储材料》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 18902:2013Imaging materials Processedimaging materials Albums,framing and storage materialsBS ISO 18902:2013 BRITISH STANDARDNational forewordThis British Standard is the

2、UK implementation of ISO 18902:2013. Itsupersedes BS ISO 18902:2007 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee CPW/42, Photography.A list of organizations represented on this committee can beobtained on request to its secretary.This publication doe

3、s not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 77550 5ICS 37.040.20Compliance with a British Standard cannot confer immunity fromlegal o

4、bligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 June 2013.Amendments issued since publicationDate Text affectedBS ISO 18902:2013 ISO 2013Imaging materials Processed imaging materials Albums, framing and storage materialsMatriaux

5、pour image Matriaux pour image aprs traitement Albums, cadrage et matriaux darchivageINTERNATIONAL STANDARDISO18902Third edition2013-07-01Reference numberISO 18902:2013(E)BS ISO 18902:2013ISO 18902:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2013All rights reserved. Unless

6、 otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the add

7、ress below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 18902:2013ISO 18902:2013(E) ISO 2013 All rights reserved iiiContents Pag

8、eForeword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 14 Materials . 24.1 Paper and board . 24.2 Plastic 34.3 Metal 44.4 Adhesives . 44.5 Writing, labelling and printing materials . 54.6 Glazing 54.7 Frames 55 Reporting 6Annex A (informative) Envelope seams . 7Annex

9、B (informative) Slip agents . 8Bibliography 9BS ISO 18902:2013ISO 18902:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through IS

10、O technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates c

11、losely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteri

12、a needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directivesAttention is drawn to the possibility that some of the elements of this document may be the subject of patent r

13、ights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patentsAny trade name used in this do

14、cument is information given for the convenience of users and does not constitute an endorsement.The committee responsible for this document is ISO/TC 42, Photography.This third edition cancels and replaces the second edition (ISO 18902:2007), which has been technically revised.iv ISO 2013 All rights

15、 reservedBS ISO 18902:2013ISO 18902:2013(E)IntroductionThis International Standard contains specifications to ensure that products used for the storage and display of imaging materials, such as envelopes, boxes, albums and frames, will not damage the enclosed imaging materials or accelerate their na

16、tural decay rates.Specifying the chemical and physical characteristics of the storage and display materials does not, by itself, ensure satisfactory storage or display behaviour. It is also essential to provide proper storage temperature, humidity and light levels (if on display), as well as protect

17、ion from the hazards of fire, water, and fungal growth, from contact with certain chemicals in solid, liquid or gaseous form (e.g. atmospheric pollutants), and from physical damage.Recommended storage conditions are given in the following International Standards for the different types of imaging ma

18、terials: ISO 18911, ISO 18918, ISO 18920, and ISO 18934.This International Standard does not apply to supplementary materials that may be stored with imaging materials such as documents and ephemera (for permanence requirements for paper for documents, see ISO 9706).Note that the term “archival” is

19、not used in International Standards for imaging materials or for storage and display materials, because the meaning of “archival” has become too ambiguous. Therefore, storage and display materials should not be referred to as “archival,” but rather as meeting the specifications of this International

20、 Standard. ISO 2013 All rights reserved vBS ISO 18902:2013BS ISO 18902:2013Imaging materials Processed imaging materials Albums, framing and storage materials1 ScopeThis International Standard specifies the principal physical and chemical requirements for album, storage and framing materials to prev

21、ent damage to processed or printed imaging materials over time. This International Standard covers requirements for paper and paperboard, plastics, metals, writing instruments, adhesives, tapes, self-adhesive labelling materials, stamping inks and pads as well as framing and glazing materials used a

22、s or in the construction of storage and display materials for black-and-white or colour reflection prints or negatives made with traditional silver-halide and silver dye bleach photographic materials, as well as dye- and pigment-based inkjet; dye diffusion thermal transfer (“dye sublimation”), and l

23、iquid- and dry-toner electrophotographic digital prints.This International Standard does not provide specifications for the design, construction or durability of the storage and display materials themselves. The requirements are limited to the characteristics of the storage or display materials that

24、 may affect the imaging materials either chemically or physically when they are stored or displayed under recommended conditions.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated refere

25、nces, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 302, Pulps Determination of Kappa numberISO 10716, Paper and board Determination of alkali reserveISO 12757-1:1998, Ball point pens and refills Part 1: G

26、eneral useISO 12757-2:1998, Ball point pens and refills Part 2: Documentary use (DOC)ISO 14145-1:1998, Roller ball pens and refills Part 1: General useISO 14145-2:1998, Roller ball pens and refills Part 2: Documentary use (DOC)ISO 18916, Imaging materials Processed imaging materials Photographic act

27、ivity test for enclosure materialsISO 18932, Imaging materials Adhesive mounting systems SpecificationsTAPPI T509, Hydrogen ion concentration (pH) of paper extracts (cold extraction method)ASTM D1193, Standard Specification for Reagent Grade Water3 Terms and definitionsFor the purposes of this docum

28、ent, the following terms and definitions apply.3.1acid-free adhesiveadhesive with a cold extraction pH equal to or greater than the reference water minus 0,5 and less than 10,0INTERNATIONAL STANDARD ISO 18902:2013(E) ISO 2013 All rights reserved 1BS ISO 18902:2013ISO 18902:2013(E)3.2acid-free paper

29、or paperboardpaper or paperboard with a cold extraction pH equal to or greater than reference water minus 0,5 and less than 10,03.3anti-blocking agentadditive or component which prevents sticking or fusing of adjacent resins or plastic films, either through microscopic bumps on the surface or by oth

30、erwise reducing the likelihood that two materials will stick togetherNote 1 to entry: Examples are talc, other silicates, and amides.3.4bufferedpaper or paperboard with an alkali reserve that is equivalent to at least 2,0 % by weight calcium carbonate (CaCO3)3.5lignin-freepaper or paperboard with a

31、Kappa number of 7,0 or less, corresponding to a lignin concentration of approximately 1,0 % or less by mass3.6photo-safematerial that meets all requirements within this International Standard so that it will not accelerate the natural aging of photographic prints or films or digitally printed images

32、Note 1 to entry: Material that only meets pH requirements or passes the photographic activity test described in ISO 18916 is not necessarily photo-safe due to other factors that may be harmful. Only materials that meet all requirements of this International Standard can be considered photo-safe.3.7s

33、lip agentcomponent added to plastic material to reduce the coefficient of friction4 Materials4.1 Paper and boardPaper or paperboard shall be acid-free as determined by a cold extraction pH measurement equal to or greater than the reference water minus 0,5 and less than 10,0 using the method given in

34、 TAPPI T509, with the following modifications. ASTM D1193 Type or Type water shall be used for this measurement and shall have a pH between 6,0 and 8,0. If the pH does not meet these requirements, the water shall be boiled for 1 h so that it meets these requirements. The temperature of the water sha

35、ll be (25 5)C and the circuit of the pH meter shall include temperature compensation. Reagent water may be added as a single 75 ml addition to limit the exposure of the extract solution to acids in the atmosphere. The sample and the reference water shall be gently agitated at least once during the 1

36、 h soak. The probe shall be rinsed with a small quantity of extract or reference water before measuring the pH.Paper and paperboard material shall include an alkali reserve of at least 2,0 % by weight calcium carbonate (CaCO3), as determined by the alkali reserve test described in ISO 10716. The alk

37、ali reserve 2 ISO 2013 All rights reservedBS ISO 18902:2013ISO 18902:2013(E)should be evenly distributed throughout the paper or paperboard. There is no maximum limit for alkali reserve content.A minimum of sizing chemicals should be used, the amount being dictated by the requirements of the end use

38、 (enclosures, overwraps, interleaving, etc.). If sizing is used, neutral or alkaline sizing chemicals (internal and/or surface) shall be employed.Unprinted, pre-consumer recycled material may be used; however, post-consumer recycled material shall not.Paper and paperboard material shall meet the req

39、uirements of the photographic activity test described in ISO 18916.Paper and paperboard material shall have a Kappa number of 7,0 or less as determined by the method described by ISO 302.Dyes or pigments used to colour the paper shall show no bleeding or transfer when soaked in distilled water for 2

40、4 h while held in direct contact with white bond paper.Each colour of paper or paperboard shall be tested separately to meet all requirements in this International Standard.Album, storage and framing materials made with paper or paperboard that are coated or laminated on both sides with a plastic fi

41、lm shall be subject to 4.2, Plastic, and not 4.1, Paper. Album, storage and framing materials that are coated or laminated on only one side with a plastic film shall be subject to both 4.1, Paper, and 4.2, PlasticFor album bindings, requirements for the photographic activity test, lignin and sizing

42、do not apply when the bindings will not come in direct contact with the imaging materials inside (either front or back), when the bindings are separated by a barrier material such as a plastic cover sheet over the pages, or when the interior lining of the binding is either a barrier or meets all of

43、the requirements in 4.1.4.2 PlasticPlastics shall meet the requirements of the photographic activity test described in ISO 18916.Chlorinated, nitrated or acetate plastic sheeting, such as polyvinyl chloride, cellulose nitrate, and cellulose acetate, shall not be used as they have poor chemical stabi

44、lity.Plasticized sheeting or coatings shall not be employed, as this might result in image transfer, sticking, or changes to the image surface. Plastics containing residual solvents or plasticizers are suspect, because these chemicals may escape and have a harmful effect on the imaging materials.Fir

45、e-retardant plastics used for containers shall contain anti-oxidants and non-halogenated fire retardants, such as antimony oxide.Album, storage and framing materials made with paper or paperboard that are coated or laminated on both sides with a plastic film shall be subject to 4.2, Plastic, and not

46、 4.1, Paper. Album, storage and framing materials that are coated or laminated on only one side with a plastic film shall be subject to both 4.1, Paper, and 4.2, Plastic.Historically, pigment inkjet prints on all paper types and dye inkjet prints on matte-surface papers have been sensitive to scuffi

47、ng and smudging, but resistance to abrasion has been improved for more recent products. These prints should be sleeved in smooth plastic enclosures; however, some plastics, such as polyester, may develop a static charge that can attract dust which may also damage the surface of prints. All valuable

48、prints should be housed in such a way that no material comes in direct contact with the surface of the print.NOTE Examples of suitable plastic enclosure materials are polyester poly(ethylene terephthalate), polystyrene, polyethylene, polypropylene, and spun-bonded polyolefins as they are usually ine

49、rt, unplasticized, and have good chemical stability. Other plastics may be satisfactory, but there has been no extended experience with such materials. ISO 2013 All rights reserved 3BS ISO 18902:2013ISO 18902:2013(E)4.3 MetalMetals used for cores, reels, cans, frames, etc. shall be non-corrodible and non-reactive, such as anodized aluminium or stainless steel. The use of steel is permissible, provided the surface is well protected by powder coating, tinning, plating, or some other corrosion-resistant finish