BS ISO 17082-2004 Pneumatic fluid power - Valves - Data to be included in supplier literature《气压传动 阀 供货商文件中的数据》.pdf

《BS ISO 17082-2004 Pneumatic fluid power - Valves - Data to be included in supplier literature《气压传动 阀 供货商文件中的数据》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 17082-2004 Pneumatic fluid power - Valves - Data to be included in supplier literature《气压传动 阀 供货商文件中的数据》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 17082:2004 Pneumatic fluid power Valves Data to be included in supplier literature ICS 23.100.50 BS ISO 17082:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 7 December 2004 BSI 7 December 2004 ISBN 0 580 45002 3

2、National foreword This British Standard reproduces verbatim ISO 17082:2004 and implements it as the UK national standard. The UK participation in its preparation was entrusted by Technical Committee MCE/18, Fluid power systems and components, to Subcommittee MCE/18/-/5, Control components, which has

3、 the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may be found in the BSI Catalogue under the section entitled “I

4、nternational Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with

5、a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related internatio

6、nal and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii to iv, pages 1 to 6, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the

7、document was last issued. Amendments issued since publication Amd. No. Date Comments Reference number ISO 17082:2004(E) OSI 4002INTERNATIONAL STANDARD ISO 17082 First edition 2004-06-01 Pneumatic fluid power Valves Data to be included in supplier literature Transmissions pneumatiques Distributeurs D

8、onnes inclure dans la documentation des fournisseurs BSISO17082:2004IS:28071 O4002(E) DPlcsid Fremia ihTs PDF file may ctnoian emdebt dedyfepcaes. In ccaocnadrw eith Aebods licensilop gnic,y this file mairp eb ynted iv roweb detu slahl ton ide ebtlnu deess the typefaces whice era hml era deddebicsne

9、de to i dnanstlaled t noeh computfrep reormign tide ehtin.g In wodlnidaot gnhis file, trapise atpecc tiereht nser ehnopsiiblity fo not infriigngn Aebods licensilop gnic.y ehT ISO tneClar Secrteiraat caceptl on siibality in this .aera Ai ebods a tredamafo kr Aebod SystemI sncotaropr.de teDails fo teh

10、 softwacudorp erts sut deo crtaee this PDF file cna f ebi dnuon tlareneG eh Info leratit evo the file; tP ehDc-Frtaeion marapterew setpo erimizde for irpnti.gn Evyre caer neeb sah taken to sneeru that the file is suitlbae fosu re yb ISO memdob rebeis. In tlnu ehikletneve y ttah lborp aem leratit gno

11、 it is f,dnuo plsaee inform ttneC ehlar Secrteiraat ta the serddaig sleb nevwo. ISO 4002 All irthgs erse.devr lnUeto sswrehise specified, on trap fo this lbupictaion maeb y cudorperro de tuilizi den yna form ro na ybm ynae,s lecetrinoc ro mecinahcal, inclidung tohpcoiypodna gn micrfoilm, wittuoh rep

12、missii non writign from ietI rehSa Ot tsserdda eh ebolw or ISOs memreb i ydobn the cnuotrfo y ttseuqer ehe.r ISO cirypothg fofice saCe tsopale 65 eneG 1121-HC 02 av leT. 4 + 10 947 22 1 11 xaF0 947 22 14 + 9 74 E-mail coirypthgiso.o gr We bwww.is.o gro Pulbisdehi n Switlrez dnaii ISO 4002 Allr ithgs

13、r esedevrBSISO17082:2004IS:28071 O4002(E) I SO 4002 All irthgs ersedevr iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO t

14、echnical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates clos

15、ely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draf

16、t International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this docum

17、ent may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 17082 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 5, Control products and components. BSISO17082:2004IS:28071 O4002(E) iv I SO 4002 A

18、ll irthgs ersedevrIntroduction In pneumatic fluid power systems, power is transmitted and controlled through air under pressure within a circuit. Typical components found in such systems are pneumatic valves. These devices control flow direction, pressure or flow rate of air in the circuit. BSISO170

19、82:2004INTENRATIONAL TSANDADR IS:28071 O4002(E)I SO 4002 All irthgs ersedevr 1Pneumatic fluid power Valves Data to be included in supplier literature 1 Scope This International Standard specifies which data are to be included in the manufacturers supplier literature that accompanies any kind of pneu

20、matic valve. These data are vital in selecting the proper valve for a particular application. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edi

21、tion of the referenced document (including any amendments) applies. ISO 1219-1, Fluid power systems and components Graphic symbols and circuit diagrams Part 1: Graphic symbols ISO 3448, Industrial liquid lubricants ISO viscosity classification ISO 4400, Fluid power systems and components Three-pin e

22、lectrical plug connectors with earth contact Characteristics and requirements ISO 5598, Fluid power systems and components Vocabulary ISO 5599-1, Pneumatic fluid power Five-port directional control valves Part 1: Mounting interface surfaces without electrical connector ISO 5599-2, Pneumatic fluid po

23、wer Five-port directional control valves Part 2: Mounting interface surfaces with optional electrical connector ISO 6358, Pneumatic fluid power Components using compressible fluids Determination of flow-rate characteristics ISO 6952, Fluid power systems and components Two-pin electrical plug connect

24、ors with earth contact Characteristics and requirements ISO 11727, Pneumatic fluid power Identification of ports and control mechanisms of control valves and other components ISO 12238, Pneumatic fluid power Directional control valves Measurement of shifting time ISO 15217, Fluid power systems and c

25、omponents 16 mm square electrical connector with earth contact Characteristics and requirements ISO 15218, Pneumatic fluid power 3/2 solenoid valves Mounting interface surfaces ISO 15407-1, Pneumatic fluid power Five-port directional control valves, sizes 18 mm and 26 mm Part 1: Mounting interface s

26、urfaces without electrical connector BSISO17082:2004IS:28071 O4002(E) 2 I SO 4002 All irthgs ersedevrISO 15407-2, Pneumatic fluid power Five-port directional control valves, sizes 18 mm and 26 mm Part 2: Mounting interface surfaces with electrical connector IEC 60529, Degrees of protection provided

27、by enclosures (IP Code) 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 5598 apply. 4 Data to be included in supplier literature The information called for in the columns titled “Types of data” and “Requirements” of Table 1 is the minimum that shall

28、be included in supplier literature. Information in the “Examples” column is given for informative purposes only. Table 1 Types of data to be included in supplier literature Type of data Requirements Examples Supply pressure range of the valve Minimum and maximum 0 to 1 600 kPa (0 to 16 bar) Operatin

29、g fluid Description compressed air inert gases vacuum other Shifting pressure range Minimum and maximum NOTE Description of any internal and/or external solenoid pilot supply requirement, where they exist, should be explained. 170 to 1 000 kPa (1,7 to 10 bar) Lubrication requirements Yes/No if yes,

30、viscosity of the lubricant ISO VG 32, in accordance with ISO 3448 Compressed air quality requirements Moisture-free, filtered with a filter rated at 40 m or finer Temperature rating Maximum and minimum NOTE The temperature rating covers the effect of ambient and fluid temperatures on the function of

31、 the valve. 10 C to +50 C Mass Amount, not including packaging 1,1 kg Dimensional standards to which the valve conforms. Identification of standard ISO 5599-1 ISO 5599-2 ISO 15218 ISO 15407-1 ISO 15407-2 Certifications The standard to which the valve has been certified. UL 429 CSA 22.2-139 EN standa

32、rds related to CE markings BSISO17082:2004IS:28071 O4002(E) I SO 4002 All irthgs ersedevr 3Table 1 (continued) Type of data Requirements Examples Dimensions length, width, height mounting holes, hole centres connecting ports, port centres other major features Valve function description Type of valve

33、 Directional control valves (for example, 3/2, 4/2, 5/2 and 5/3) Flow control valves Non-return (check) valves, etc. Valve connection symbols and port identification In accordance with ISO 1219-1 and ISO 11727. Flow rating b and C, determined in accordance with the test method in ISO 6358. b = 0,3;

34、C = 560 dm 3 /(skPa) (5,6 dm 3 /sbar) NOTE Flow rating coefficients determined in accordance with local or regional standards or practices may be included. Basic materials of construction Description of major elements: body base valving element seals springs Aluminium Zinc Nitrile BSISO17082:2004IS:

35、28071 O4002(E) 4 I SO 4002 All irthgs ersedevrTable 1 (continued) Type of data Requirements Examples Valve type Description of valving element spool with O-rings spool, bonded spool, packed bore poppet lapped spool lapped disc Control mechanisms Description of control mechanism types Driving types:

36、manual mechanical remote pilot solenoid Return types: spring spring and pilot internal or external pilot Solenoid characteristics Direct-acting Solenoid pilot internal (see minimum shifting pressure, above) external pilot option yes/no, with explanation of how external pilot is connected. Electrical

37、 characteristics operating voltage (AC, DC), including ratings inrush and holding current for AC power consumption solenoid duty cycles type of electrical connections (ISO 4400, ISO 6952, ISO 15217, or other types) arc suppression option solenoid overrides yes/no type of override 120 V AC +10%; 15%;

38、 24 V DC 10 % 0,09 A inrush; 0,07 A holding 4,8 W; 6,0 VA at 60 Hz 100 % DIN, flying leads, etc. locking or non-locking extended or flush button, lever, etc. Wiring information and polarity Degree of protection provided by enclosure for electrical equipment IP 65 (in accordance with IEC 60529) Light

39、s, including listing of colour LED neon other type Port type and size threaded port push-to-connect (instant) barb connection other 1/4-inch NPT; G 1/4; 1/4 R c5/32 or 4 mm tubing Built-in flow controls Describe, if available. Shifting time Determined in accordance with the test method in ISO 12238

40、Shifting on-time = 50 ms Shifting off-time = 80 ms Actuating force or torque and travel For valves with manual and/or mechanical control 1 N palm button shift force BSISO17082:2004IS:28071 O4002(E) I SO 4002 All irthgs ersedevr 55 Identification statement (reference to this International Standard) U

41、se the following statement in test reports, catalogues and sales literature when electing to comply with this International Standard: “Pneumatic valve data given in accordance with ISO 17082, Pneumatic fluid power Valves Data to be included in supplier literature.” BSISO17082:2004IS:28071 O4002(E) 6

42、 I SO 4002 All irthgs ersedevrBibliography 1 ANSI/(NFPA)T3.21.3-1990, Pneumatic fluid power Flow rating test procedure and reporting method For fixed orifice components 2 SAE J2051-JUN92, Qualifications for Four-Way Subbase Mounted Air Valves for Automotive Manufacturing Applications BSISO17082:2004

43、blankBS ISO 17082:2004 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revi

44、sions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or am

45、biguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures t

46、hat subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available

47、from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on nation

48、al, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these