BS ISO 11639-2010 Aerospace - Part numbering for hose assemblies《航空航天 软组件零件号码》.pdf

《BS ISO 11639-2010 Aerospace - Part numbering for hose assemblies《航空航天 软组件零件号码》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 11639-2010 Aerospace - Part numbering for hose assemblies《航空航天 软组件零件号码》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwide NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Standards Publication BS ISO 11639:2010 Aerospace Part numbering for hose assembliesBS ISO 11639:2010 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 11639:

2、2010. The UK participation in its preparation was entrusted to Technical Committee ACE/69, Aerospace hydraulic systems, fluids and components. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the neces

3、sary provisions of a contract. Users are responsible for its correct application. BSI 2010 ISBN 978 0 580 60862 9 ICS 49.080 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy

4、Committee on 31 July 2010 Amendments issued since publication Date Text affectedBS ISO 11639:2010Reference number ISO 11639:2010(E) ISO 2010INTERNATIONAL STANDARD ISO 11639 First edition 2010-06-01 Aerospace Part numbering for hose assemblies Aronautique et espace Numerotation des lments de systmes

5、de tuyauterie BS ISO 11639:2010 ISO 11639:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer

6、performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create th

7、is PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Cent

8、ral Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission

9、 in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2010 All rights reservedBS

10、 ISO 11639:2010 ISO 11639:2010(E) ISO 2010 All rights reserved iiiContents Page Foreword iv 1 Scope1 2 Terms and definitions .1 3 Construction of part numbers1 3.1 Part number length1 3.2 Basic numbers.1 3.3 Size codes 1 3.4 Assembly length codes 2 3.5 Assembly length tolerances.3 3.6 Fitting type c

11、odes4 3.7 Fitting configuration codes 4 3.8 Orientation codes5 3.9 General requirements .5 3.10 Limitations .6 4 Complex numbers .6 4.1 General .6 4.2 Hose assembly option codes.6 4.3 Sleeving Codes7 5 Hose assembly part numbering guidelines8 5.1 15-digit part numbers8 5.2 20-digit part numbers8 BS

12、ISO 11639:2010 ISO 11639:2010(E) iv ISO 2010 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical co

13、mmittees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with th

14、e International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft Internati

15、onal Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be

16、the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 11639 was prepared by Technical Committee ISO/TC 20, Aircraft and space vehicles, Subcommittee SC 10, Aerospace fluid systems and components. BS ISO 11639:2010 INTERNATIONAL STANDARD IS

17、O 11639:2010(E) ISO 2010 All rights reserved 1Aerospace Part numbering for hose assemblies 1 Scope This International Standard specifies a hose-assembly designation system and presents a part numbering scheme for aerospace fluid-system hose assemblies. Standardization on certain numbering systems pr

18、ovides for numbering simplicity, ease of interchangeability, and the suppression (as required), standardization and limitation of usable codes. 2 Terms and definitions For the purposes of this document the following terms and definitions apply. 2.1 basic standard number stem number number that is th

19、e drawing specification or standard number for a part or family of parts 2.2 dash number all digits of a part number, other than the basic standard number, used to define and differentiate individual part configurations with the standard 2.3 non-significant dash number dash number that is numerical,

20、 sequential and contains no coding 2.4 digit number, alpha character or symbol that occupies a space within a part number 3 Construction of part numbers 3.1 Part number length To the maximum extent possible, part numbers should be limited in length to 15 digits. Part numbers up to 20 digits in lengt

21、h are acceptable, if required to fully differentiate part numbers. 3.2 Basic numbers It is recommended that the basic standard number be a maximum of seven digits in length. 3.3 Size codes Size codes for hose assemblies shall be in accordance with Table 1. Hose assembly size codes shall be alphabeti

22、c. BS ISO 11639:2010 ISO 11639:2010(E) 2 ISO 2010 All rights reservedTable 1 Size codes Hose or fitting size Metric aImperial bSize code DN05 03 D DN06 04 E DN08 05 F DN10 06 G DN12 08 H DN16 10 J DN20 12 K DN25 16 M DN32 20 N DN40 24 P DN50 32 R a DN size in millimetres, example: DN05; 5 mm. b Dash

23、 size in 1/16 inch, example: 05 = 5/16 inch diameter. 3.4 Assembly length codes 15-digit part numbers Metric = three-digit code as given in Table 2. Inch = three digits in inches: first two digits in whole inches, last digit in 1/8 inch. 20-digit part numbers Metric = four digits in millimetres. Inc

24、h = four digits in inches: first three digits in whole inches, last digit in 1/8 inch. Hose assembly lengths shall be coded in whole millimetres. The length code of a hose assembly shall always be three digits long, using zeros when necessary. For hose assemblies length W 1 m, the length code shall

25、be defined using a prefix letter. BS ISO 11639:2010 ISO 11639:2010(E) ISO 2010 All rights reserved 3Table 2 Three-digit metric assembly length codes Length mm Three-digit metric code 0 to 999 000 to 999 1 000 to 1 099 A00 to A99 1 100 to 1 199 B00 to B99 1 200 to 1 299 C00 to C99 1 300 to 1 399 D00

26、to D99 1 400 to 1 499 E00 to E99 1 500 to 1 599 F00 to F99 1 600 to 1 699 G00 to G99 1 700 to 1 799 H00 to H99 1 800 to 1 899 J00 to J99 1 900 to 1 999 K00 to K99 2 000 to 2 099 L00 to L99 2 100 to 2 199 M00 to M99 2 200 to 2 299 N00 to N99 2 300 to 2 399 P00 to P99 2 400 to 2 499 R00 to R99 2 500 t

27、o 2 599 S00 to S99 2 600 to 2 699 T00 to T99 2 700 to 2 799 U00 to U99 2 800 to 2 899 V00 to V99 2 900 to 2 999 W00 to W99 3 000 to 3 099 Y00 to Y99 3.5 Assembly length tolerances The tolerances on assembly lengths shall be as follows. a) 3,2 mm for lengths under 0,46 m; 0,125 in for lengths under 1

28、8 in. b) 6,4 mm for lengths from 0,46 to 0,91 m exclusive; 0,125 in for lengths under 18 in. c) 12,7 mm for lengths from 0,91 to 1,3 m exclusive; 0,500 in for lengths from 36 to 50 in exclusive. d) 1 % for lengths of 1,3 m and over; 1 % for lengths of 50 in and over. BS ISO 11639:2010 ISO 11639:2010

29、(E) 4 ISO 2010 All rights reserved3.6 Fitting type codes Fitting type codes shall be in accordance with Table 3. Table 3 Fitting type codes Code Fitting thread type M Metric (mm) E Imperial (inch) 3.7 Fitting configuration codes Fitting configuration codes for hose assemblies shall be in accordance

30、with Table 4. Table 4 Fitting configuration codes Assembly aCode A B C D E F aThe fitting shape is given for information only. BS ISO 11639:2010 ISO 11639:2010(E) ISO 2010 All rights reserved 53.8 Orientation codes Double-elbow hose assemblies or other hose assemblies requiring end coupling orientat

31、ion shall have a three-digit orientation code, given in whole degrees, using zeros when necessary. The angle is determined with anti-clockwise orientation form the datum position given by the end coupling nearest to the observer. See Figure 1 and Table 5. The angle, , shall be in accordance with Tab

32、le 5. Figure 1 Angle determining end coupling orientation code Table 5 Orientation codes Angle degrees Code letter Angle degrees Code letter 0,0 165,0 L 15,0 A 180,0 M 30,0 B 195,0 N 45,0 C 210,0 P 60,0 D 225,0 R 75,0 E 240,0 S 90,0 F 255,0 T 105,0 G 270,0 U 120,0 H 285,0 V 135,0 J 300,0 W 150,0 K 3

33、30,0 Y 3.9 General requirements Whenever possible, a hyphen (-) should be used to separate numbers from each other (in lieu of a space) but should not be used to separate letter codes from numbers. Running letter or number codes consecutively should be avoided but is not prohibited. A hyphen shall c

34、onstitute one digit. If consecutive number codes or letter codes are used, no more than four successive number or letter codes shall be used, and adjacent codes shall not be ambiguous in meaning. When establishing a new basic series of numbering, issuance of the short basic standard number series sh

35、ould be limited to those parts requiring long, complex dash numbers, their use being justified in order to stay within the 15-digit limitation. Typical fluid system parts requiring this would be hose assemblies and reducer/expander tee fittings. A short basic standard number may also be needed to st

36、ay within the 20-digit limitation. BS ISO 11639:2010 ISO 11639:2010(E) 6 ISO 2010 All rights reserved3.10 Limitations The following limitations apply. Letters, “I”, “O”, “Q”, “X”, and “Z” shall not be used. Other letters shall be upper-case (capitalized). Numbers shall be Arabic numerals. Blank spac

37、es are not permitted. Symbols such as parentheses ( ), asterisk *, degree , plus + and minus shall not be used, except when referencing a government or industry document whose identification contains such a symbol. The total length of the part number, including the dash number(s), shall not exceed 1

38、5 digits, except under special circumstances, where the part number length may be a maximum of 20 digits. The dash number shall have the same characteristics as the basic standard number and may be composed of numbers, letters or any combination thereof. Part standard drawing revision letters (if an

39、y) shall not be included in the part number. 4 Complex numbers 4.1 General The following option codes, sleeving codes, numeric size codes, letter size codes, length codes, and angular orientation codes are established standards for use in the construction of significant part numbers. Use of these co

40、des is not mandatory if a non-significant numbering discipline is used. 4.2 Hose assembly option codes Option code letters to be used in the part number shall be in accordance with Table 6. Table 6 Option codes Code letter Options L Tie wire holes N Dry film lubricated H Tie wire holes and dry film

41、lubricated threads BS ISO 11639:2010 ISO 11639:2010(E) ISO 2010 All rights reserved 74.3 Sleeving Codes Sleeving code letters for each part standard shall be in accordance with Table 7. Table 7 Sleeving codes Temperature limits Sleeve code Sleeve description C C Hose only Hose specification limits A

42、 Abrasion sleeve, tubular, PTFE, black 54 to 232 65 to 450 B Abrasion sleeve, spiral coil, nylon, black 54 to 135 65 to 275 C Firesleeve, tubular, silicone, fibreglass, 15 min duration, fireproof Sil-FG 54 to 232 65 to 450 54 to 177 65 to 350 D Abrasion sleeve, internal, silicone Inactive for new de

43、sign superseded by code K E Abrasion sleeve, heat shrink, FEP 54 to 177 65 to 350 F Abrasion sleeve, heat shrink polyolefin, black 54 to 135 65 to 275 G Firesleeve, tubular, silicone fibreglass, 5 min duration, fire resistant Sil-FG 54 to 232 65 to 450 H Firesleeve, integral, silicone, 15 min durati

44、on, fire proof 54 to 232 65 to 450 J Firesleeve, integral, silicone, 5 min duration, fire resistant 54 to 232 65 to 450 K Abrasion sleeve, integral braided, polyester 54 to 149 65 to 300 L Abrasion sleeve, spiral coil, PTFE 54 to 232 65 to 450 18 to 93 0 to 200 M Abrasion sleeve, spiral coil, butyra

45、te, black Inactive for new design 54 to 232 65 to 450 N Firesleeve, tubular, silicone fibreglass, snug-fit, 15 min duration, fire proof Sil-FG Inactive for new design BS ISO 11639:2010 ISO 11639:2010(E) 8 ISO 2010 All rights reserved5 Hose assembly part numbering guidelines 5.1 15-digit part numbers

46、 5.2 20-digit part numbers BS ISO 11639:2010BS ISO 11639:2010 ISO 11639:2010(E) ICS 49.080 Price based on 8 pages ISO 2010 All rights reserved This page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, i

47、nformation and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. British Standards Institution (BSI) raising standards worldwide BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK Tel +44 (0)20 8996 9001 Fax +44

48、(0)20 8996 7001 British Standards are updated by amendment or revision. Users of British Stan- dards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and serv- ices. We would be grateful if anyone finding an i

49、naccuracy or ambiguity while using this British Standard would inform the Secretary of the technical com- mittee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 BSI offers Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Tel: +44 (0)20 8