BS EN ISO 11148-7-2012 Hand-held non-electric power tools Safety requirements Grinders《手持式非电动工具 安全要求 磨床》.pdf

《BS EN ISO 11148-7-2012 Hand-held non-electric power tools Safety requirements Grinders《手持式非电动工具 安全要求 磨床》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 11148-7-2012 Hand-held non-electric power tools Safety requirements Grinders《手持式非电动工具 安全要求 磨床》.pdf（66页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 11148-7:2012Hand-held non-electric powertools Safety requirementsPart 7: GrindersBS EN ISO 11148-7:2012 BRITISH STANDARDNational forewordThis British Standard is the UK

2、 implementation of EN ISO 11148-7:2012. It supersedes BS EN 792-7:2001+A1:2008, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee MCE/8/-/2, Hand-held, non-electric power tools - Safety.A list of organizations represented on this committee can be obtaine

3、d on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012Published by BSI Standards Limited 2012ISBN 978 0 580 63381 2 ICS 25.140.10 Compliance with

4、a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2012.Amendments issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM E

5、N ISO 11148-7 August 2012 ICS 25.140.10 Supersedes EN 792-7:2001+A1:2008English Version Hand-held non-electric power tools - Safety requirements - Part 7: Grinders (ISO 11148-7:2012) Machines portatives moteur non lectrique - Exigences de scurit - Partie 7: Meuleuses (ISO 11148-7:2012) Handgehaltene

6、 nicht elektrisch betriebene Maschinen - Sicherheitsanforderungen - Teil 7: Schleifmaschinen fr Schleifkrper (ISO 11148-7:2012) This European Standard was approved by CEN on 25 August 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for g

7、iving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three o

8、fficial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies

9、 of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spai

10、n, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN nat

11、ional Members. Ref. No. EN ISO 11148-7:2012: EBS EN ISO 11148-7:2012 EN ISO 11148-7:2012 (E) 3 Foreword This document (EN ISO 11148-7:2012) has been prepared by Technical Committee ISO/TC 118 “Compressors and pneumatic tools, machines and equipment“ in collaboration with Technical Committee CEN/TC 2

12、55 “Hand-held, non-electric power tools - Safety” the secretariat of which is held by SIS. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2013, and conflicting national standards shall b

13、e withdrawn at the latest by February 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 792-7:2001+A1:

14、2008. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.

15、According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Ger

16、many, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 11148-7:2012 has been approved by CEN as EN ISO 1114

17、8-7:2012 without any modification. BS EN ISO 11148-7:2012EN ISO 11148-7:2012 (E) 4 Annex ZA (informative) Relationship between this International Standard and the Essential Requirements of EU Directive 2006/42/EC This European Standard has been prepared under a mandate given to CEN by the European C

18、ommission and the European Free Trade Association to provide a means of conforming to Essential Requirements of the New Approach Directive 2006/42/EC on machinery. Once this standard is cited in the Official Journal of the European Union under that Directive and has been implemented as a national st

19、andard in at least one Member State, compliance with the clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity with the corresponding Essential Requirements of that Directive and associated EFTA regulations. WARNING Other requirements and othe

20、r EU Directives may be applicable to the product(s) falling within the scope of this standard. BS EN ISO 11148-7:2012ISO 11148-7:2012(E) ISO 2012 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope 12 Normative references . 23 Terms and definitions . 23.1 General terms and definitio

21、ns . 23.2 Terms and definitions related to grinders 43.3 Symbols . 54 Safety requirements and/or protective measures 54.1 General . 54.2 Mechanical safety 64.3 Thermal safety 214.4 Noise reduction 224.5 Vibration .224.6 Materials and substances processed, used or exhausted .234.7 Ergonomics .234.8 C

22、ontrols .235 Verification 245.1 General conditions for the tests 245.2 Noise .245.3 Vibration .245.4 Test of deformation of flanges .245.5 Test of guards .255.6 Unintentional start .265.7 Power tool construction 275.8 Test of alternative flanges .275.9 Structure of verification of safety requirement

23、s .286 Information for use .296.1 Marking, signs and written warnings .296.2 Instructions handbook .306.3 Operating instructions .356.4 Data .366.5 Maintenance instructions 36Annex A (informative) List of significant hazards 38Annex B (informative) Examples of grinders covered by this part of ISO 11

24、148 40Annex C (normative) Symbols for labels and signs42Annex D (informative) Examples of abrasive products for hand-held grinders 43Annex E (informative) Example of calculating procedure of clamping force .50Bibliography .54BS EN ISO 11148-7:2012ISO 11148-7:2012(E)ForewordISO (the International Org

25、anization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been establi

26、shed has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardizatio

27、n.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Pu

28、blication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent

29、 rights.ISO 11148-7 was prepared by Technical Committee ISO/TC 118, Compressors and pneumatic tools, machines and equipment, Subcommittee SC 3, Pneumatic tools and machines. ISO 11148 consists of the following parts, under the general title Hand-held non-electric power tools Safety requirements: Par

30、t 1: Assembly power tools for non-threaded mechanical fasteners Part 2: Cutting-off and crimping power tools Part 3: Drills and tappers Part 4. Non-rotary percussive power tools Part 5: Rotary percussive drills Part 6: Assembly power tools for threaded fasteners Part 7: Grinders Part 8: Sanders and

31、polishers Part 9: Die grinders Part 10: Compression power tools Part 11: Nibblers and shears Part 12: Circular, oscillating and reciprocating sawsA Part 13 dealing with fastener driving tools is under preparation.iv ISO 2012 All rights reservedBS EN ISO 11148-7:2012ISO 11148-7:2012(E)IntroductionThi

32、s document is a type-C standard as stated in ISO 12100.The machinery concerned and the extent to which hazards, hazardous situations and events are covered are defined in the Scope of this part of ISO 11148.When requirements of this type-C standard are different from those which are stated in type-A

33、 or -B standards, the requirements of this type-C standard take precedence over the requirements of other standards, for machines that have been designed and built according to the requirements of this type-C standard.ISO 11148 consists of a number of independent parts for individual types of hand-h

34、eld non-electric power tools.Certain parts of ISO 11148 cover hand-held non-electric power tools driven by internal combustion engines powered by gaseous or liquid fuel. In these parts, the safety aspects relating to internal combustion engines are found in a normative annex.The parts are type-C sta

35、ndards and refer to pertinent standards of type A and B where such standards are applicable. ISO 2012 All rights reserved vBS EN ISO 11148-7:2012BS EN ISO 11148-7:2012Hand-held non-electric power tools Safety requirements Part 7: GrindersIMPORTANT The colours represented in the electronic file of th

36、is document can be neither viewed on screen nor printed as true representations. For the purposes of colour matching, see ISO 3864-4, which provides colorimetric and photometric properties together with, as a guideline, references from colour order systems.1 ScopeThis part of ISO 11148 specifies saf

37、ety requirements for hand-held non-electric power tools (hereinafter “grinders”) intended for grinding and cutting-off with abrasive products, for use on all kinds of materials. The grinders can be powered by compressed air or hydraulic fluid and are intended to be used by one operator and supported

38、 by the operators hand or hands, with or without a suspension, e.g. a balancer.NOTE 1 At the time of publication, no grinders driven by internal combustion engines are known (other than cutting-off machines within the scope of ISO 19432). Once these are identified, it is intended to amend this part

39、of ISO 11148 to include such power tools.This part of ISO 11148 is applicable to grinders used with: abrasive products with a peripheral operating speed less than or equal to 80 m/s; cutting-off wheels with a peripheral operating speed less than or equal to 100 m/s; abrasive products with an outside

40、 nominal diameter less than or equal to 230 mm; cutting-off wheels with an outside nominal diameter less than or equal to 250 mm; wire brushes; diamond and reinforced (segmented) wheels with an outside nominal diameter less than or equal to 450 mm; flap discs and flap wheels.NOTE 2 For examples of g

41、rinders, see Annex B.NOTE 3 Typical abrasive products used together with hand-held grinders are listed in Annex D.This part of ISO 11148 does not cover special requirements and modifications of grinders for the purpose of mounting them in fixtures.This part of ISO 11148 is not applicable to: die gri

42、nders with collets, which are treated in ISO 11148-9; polishers and sanders (i.e. tools used with coated abrasives except flap discs and flap wheels), which are treated in ISO 11148-8; cutting-off machines which are driven by internal combustion engines and are used for cutting construction material

43、s, which are treated in ISO 19432; shaft-mounted wire brushes, which are treated in ISO 11148-9.INTERNATIONAL STANDARD ISO 11148-7:2012(E) ISO 2012 All rights reserved 1BS EN ISO 11148-7:2012ISO 11148-7:2012(E)This part of ISO 11148 deals with all significant hazards, hazardous situations or hazardo

44、us events relevant to grinders when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, with the exception of the use of grinders in potentially explosive atmospheres.NOTE 4 EN 13463-1 gives requirements for non-electrical equipment for pote

45、ntially explosive atmospheres.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applie

46、s.ISO 3857-3, Compressors, pneumatic tools and machines Vocabulary Part 3: Pneumatic tools and machinesISO 5391, Pneumatic tools and machines VocabularyISO 12100:2010, Safety of machinery General principles for design Risk assessment and risk reductionISO 13732-1, Ergonomics of the thermal environme

47、nt Methods for the assessment of human responses to contact with surfaces Part 1: Hot surfacesISO 13732-3, Ergonomics of the thermal environment Methods for the assessment of human responses to contact with surfaces Part 3: Cold surfacesISO 15744, Hand-held non-electric power tools Noise measurement

48、 code Engineering method (grade 2)ISO 17066, Hydraulic tools VocabularyISO 20643, Mechanical vibration Hand-held and hand-guided machinery Principles for evaluation of vibration emissionISO 28927-1:2009, Hand-held portable power tools Test methods for evaluation of vibration emission Part 1: Angle a

49、nd vertical grindersISO 28927-4, Hand-held portable power tools Test method for evaluation of vibration emission Part 4: Straight grindersEN 10111, Continuously hot rolled low carbon steel sheet and strip for cold forming Technical delivery conditionsEN 10130, Cold rolled low carbon steel flat products for cold forming Technical delivery conditionsEN 12096, Mechanical vibration Declaration and verification of vibration emission valuesEN 12418, Masonry and stone cutting-off machines for