BS EN ISO 11148-3-2012 Hand-held non-electric power tools Safety requirements Drills and tappers《手持式非电动工具 安全要求 钻孔机和攻丝机》.pdf

《BS EN ISO 11148-3-2012 Hand-held non-electric power tools Safety requirements Drills and tappers《手持式非电动工具 安全要求 钻孔机和攻丝机》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 11148-3-2012 Hand-held non-electric power tools Safety requirements Drills and tappers《手持式非电动工具 安全要求 钻孔机和攻丝机》.pdf（38页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 11148-3:2012Hand-held non-electric power tools Safety requirementsPart 3: Drills and tappersCopyright European Committee for Standardization Provided by IHS under licen

2、se with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 11148-3:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 11148-3:2012. It supersedes BS EN ISO 11148-3:2010 which is withdrawn.The UK participation in

3、 its preparation was entrusted to Technical Committee MCE/8/-/2, Hand-held, non-electric power tools - Safety.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Use

4、rs are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013ISBN 978 0 580 78565 8 ICS 25.100.30; 25.140.10 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under th

5、e authority of the Standards Policy and Strategy Committee on 31 January 2013.Amendments issued since publicationDate T e x t a f f e c t e dCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license fr

6、om IHS-,-,-EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 11148-3 December 2012 ICS 25.140.10 Supersedes EN ISO 11148-3:2010English Version Hand-held non-electric power tools - Safety requirements - Part 3: Drills and tappers (ISO 11148-3:2012) Machines portatives moteur non lectrique - Ex

7、igences de scurit - Partie 3: Perceuses et taraudeuses (ISO 11148-3:2012) Handgehaltene nicht elektrisch betriebene Maschinen - Sicherheitsanforderungen - Teil 3: Bohrmaschinen und Gewindeschneider (ISO 11148-3:2012) This European Standard was approved by CEN on 17 December 2012. CEN members are bou

8、nd to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the C

9、EN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre

10、has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,

11、Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012

12、 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 11148-3:2012: ECopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from I

13、HS-,-,-BS EN ISO 11148-3:2012EN ISO 11148-3:2012 (E) 3 Foreword This document (EN ISO 11148-3:2012) has been prepared by Technical Committee ISO/TC 118“Compressors and pneumatic tools, machines and equipment“ in collaboration with Technical CommitteeCEN/TC 255 “Hand-held, non-electric power tools -

14、Safety” the secretariat of which is held by SIS. This European Standard shall be given the status of a national standard, either by publication of an identicaltext or by endorsement, at the latest by June 2013, and conflicting national standards shall be withdrawn atthe latest by June 2013. Attentio

15、n is drawn to the possibility that some of the elements of this document may be the subject of patentrights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 11148-3:2010. This document has been prepared under a mandate g

16、iven to CEN by the European Commission and theEuropean Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the n

17、ational standards organisations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, CzechRepublic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Latvia, Lit

18、huania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 11148-3:2012 has been approved by CEN as a EN ISO 11148-3:2012 without anymodification. Copyright European Commi

19、ttee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 11148-3:2012EN ISO 11148-3:2012 (E) 4 Annex ZA (informative) Relationship between this European Standard and the EssentialRequirements of EU Dir

20、ective 2006/42/EC This European Standard has been prepared under a mandate given to CEN by the European Commissionand the European Free Trade Association to provide a means of conforming to Essential Requirements of theNew Approach Directive 2006/42/EC on machinery. Once this standard is cited in th

21、e Official Journal of the European Union under that Directive and has beenimplemented as a national standard in at least one Member State, compliance with the clauses of thisstandard confers, within the limits of the scope of this standard, a presumption of conformity with thecorresponding Essential

22、 Requirements of that Directive and associated EFTA regulations. WARNING Other requirements and other EU Directives may be applicable to the product(s) fallingwithin the scope of this standard. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo re

23、production or networking permitted without license from IHS-,-,-BS EN ISO 11148-3:2012ISO 11148-3:2012(E) ISO 2012 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope 12 Normative references . 13 Terms and definitions . 23.1 General definitions 23.2 Definitions related to drills and

24、 tappers 44 Safety requirements and/or protective measures 44.1 General . 44.2 Mechanical safety 44.3 Thermal safety 54.4 Noise reduction 54.5 Vibration . 64.6 Materials and substances processed, used or exhausted . 64.7 Ergonomics . 74.8 Controls . 75 Verification 85.1 General conditions for tests

25、. 85.2 Noise . 85.3 Vibration . 85.4 Unintentional start . 85.5 Power tool construction 85.6 Structure of verification of safety requirements . 96 Information for use . 96.1 Marking, signs and written warnings . 96.2 Instructions handbook .106.3 Operating instructions .156.4 Data .156.5 Maintenance

26、instructions 16Annex A (informative) List of significant hazards 17Annex B (informative) Examples of drills and tappers covered by this part of ISO 11148 .19Annex C (normative) Symbols for labels and signs21Annex D (normative) Additional safety requirements related to internal combustion engine powe

27、r tools .23Bibliography .27Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 11148-3:2012ISO 11148-3:2012(E)ForewordISO (the International Organization for Standardizatio

28、n) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be rep

29、resented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards ar

30、e drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Internationa

31、l Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 11148-3 was prep

32、ared by Technical Committee ISO/TC 118, Compressors and pneumatic tools, machines and equipment, Subcommittee SC 3, Pneumatic tools and machines.This second edition cancels and replaces the first edition (ISO 11148-3:2010), of which it constitutes a minor revision.ISO 11148 consists of the following

33、 parts, under the general title Hand-held non-electric power tools Safety requirements: Part 1: Assembly power tools for non-threaded mechanical fasteners Part 2: Cutting-off and crimping power tools Part 3: Drills and tappers Part 4: Non-rotary percussive power tools Part 5: Rotary percussive drill

34、s Part 6: Assembly power tools for threaded fasteners Part 7: Grinders Part 8: Sanders and polishers Part 9: Die grinders Part 10: Compression power tools Part 11: Nibblers and shears Part 12: Circular, oscillating and reciprocating sawsA part 13, dealing with fastener driving tools, is under prepar

35、ation.iv ISO 2012 All rights reservedCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 11148-3:2012ISO 11148-3:2012(E)IntroductionThis document is a type C standard as st

36、ated in ISO 12100.The machinery concerned and the extent to which hazards, hazardous situations and events are covered are defined in the Scope of this part of ISO 11148.When provisions of this type C standard are different from those that are stated in type A or B standards, the requirements of thi

37、s type C standard take precedence over the requirements of other standards for machines that have been designed and built according to the requirements of this type C standard.ISO 11148 consists of a number of independent parts for individual types of hand-held, non-electric power tools.Certain elem

38、ents of this part of ISO 11148 cover hand-held, non-electric power tools driven by internal combustion engines powered by gaseous or liquid fuel. In these parts, the safety aspects relating to internal combustion engines are found in a normative annex.The parts are type C standards and refer to pert

39、inent standards of types A and B where such standards are applicable. ISO 2012 All rights reserved vCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 11148-3:2012Copyrigh

40、t European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 11148-3:2012Hand-held non-electric power tools Safety requirements Part 3: Drills and tappersIMPORTANT The electronic file of th

41、is document contains colours that are considered useful for the correct understanding of the document. Users should consider printing this document using a colour printer. ISO 3864-4 provides colorimetric and photometric properties together with, as a guideline, references from colour order systems.

42、1 ScopeThis part of ISO 11148 applies to hand-held non-electric power tools (hereinafter “drills and tappers”) intended for rotary drilling of holes in all kinds of material, e.g. wood, metal, concrete and plastics, or for tapping and cleaning threads in metal and plastics. The drills and tappers ca

43、n be powered by compressed air, hydraulic fluid or internal combustion engines and are intended for use by one operator and supported by the operators hand or hands, with or without a suspension, e.g. a balancer.This part of ISO 11148 is applicable to drills; heavy duty drills with two handles; tapp

44、ers.NOTE 1 For examples of drills and tappers, see Annex B.This part of ISO 11148 is not applicable to special requirements and modifications of drills and tappers for the purpose of mounting them in fixtures.This part of ISO 11148 deals with all significant hazards, hazardous situations or hazardou

45、s events when drills and tappers are used as intended and under conditions of misuse that are reasonably foreseeable by the manufacturer, with the exception of their use in potentially explosive atmospheres.NOTE 2 EN 13463-1 gives requirements for non-electrical equipment for potentially explosive a

46、tmospheres.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 3857-3, Compr

47、essors, pneumatic tools and machines Vocabulary Part 3: Pneumatic tools and machinesISO 3864-2, Graphical symbols Safety colours and safety signs Part 2: Design principles for product safety labelsISO 5391, Pneumatic tools and machines VocabularyISO 7000, Graphical symbols for use on equipment Regis

48、tered symbols1)ISO 9158, Road vehicles Nozzle spouts for unleaded gasoline1) The graphical symbol collections of ISO 7000, ISO 7001 and ISO 7010 are also available online in the ISO web store. For more information, consult http:/www.iso.org/iso/fr/publications_and_e-products/databases.htm.INTERNATIONAL STANDARD ISO 11148-3:2012(E) ISO 2012 All rights reserved 1Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN