BS EN ISO 4796-3-2001 Laboratory glassware Bottles Aspirator bottles《实验室玻璃器皿 瓶 吸气瓶》.pdf

《BS EN ISO 4796-3-2001 Laboratory glassware Bottles Aspirator bottles《实验室玻璃器皿 瓶 吸气瓶》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 4796-3-2001 Laboratory glassware Bottles Aspirator bottles《实验室玻璃器皿 瓶 吸气瓶》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN ISO 4796-3:2001 Inc

2、orporating Corrigendum No. 1 The European Standard EN ISO 4796-3:2000 has the status of a British Standard ICS 71.040.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Laboratory glassware Bottles Part 3: Aspirator bottlesThis British Standard, having been prepared under the

3、direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 April 2001 BSI 5 October 2001 ISBN 0 580 34837 7 BS EN ISO 4796-3:2001 Amendments issued since publication Amd. No. Date Comments 13417 Corrigendum

4、No. 1 5 October 2001 Incorporating annex ZA. National foreword This British Standard is the official English language version of EN ISO 4796-3:2000. It is identical with ISO 4796-3:2000. The UK participation in its preparation was entrusted by Technical Committee LBI/36, Laboratory glassware and rel

5、ated apparatus, to Subcommittee LBI/36/2, General laboratory glass and plastics ware, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK inter

6、ests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include

7、an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards C

8、orrespondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard doe

9、s not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN ISO title page, the EN ISO foreword page, the ISO title page, pages ii and iii, a blank page, pages 1 to 4, the annex ZA page and a back cover. The BSI copyri

10、ght notice displayed in this document indicates when the document was last issued.EUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM ENISO47963 April2000 ICS71.040.20 Englishversion LaboratoryglasswareBottlesPart3:Aspiratorbottles(ISO 47963:2000) VerreriedelaboratoireFlaconsPartie3:Flacons tubulurebasse

11、(ISO47963:2000) LaborgerteausGlasFlaschenTeil3:Tubusflaschen (ISO47963:2000) ThisEuropeanStandardwasapprovedbyCENon1April2000. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Upt

12、odatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheManagementCentreortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownla

13、nguageandnotifiedtotheManagementCentrehasthesamestatusasthe official versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,CzechRepublic,Denmark,Finland,France,Germany,Greece, Iceland,Ireland,Italy,Luxembourg,Netherlands,Norway,Portugal,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEAN

14、COMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2000CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.ENISO47963:2000EgaPe2 INESO7469:30020 Foreword Corrected20010328 The

15、textoftheInternationalStandardISO47963:2000hasbeenpreparedbyTechnical CommitteeISO/TC48“Laboratoryglasswareandrelatedapparatus“incollaborationwith TechnicalCommitteeCEN/TC332“Laboratoryequipment“,thesecretariatofwhichisheldby DIN. ThisEuropeanStandardshallbegiventhestatusofanationalstandard,eitherby

16、publication ofanidenticaltextorbyendorsement,atthelatestbyOctober2000,andconflictingnational standardsshallbewithdrawnatthelatestbyOctober2000. AccordingtotheCEN/CENELECInternalRegulations,thenationalstandardsorganizationsof thefollowingcountriesareboundtoimplementthisEuropeanStandard:Austria,Belgiu

17、m, CzechRepublic,Denmark,Finland,France,Germany,Greece,Iceland,Ireland,Italy, Luxembourg,Netherlands,Norway,Portugal,Spain,Sweden,SwitzerlandandtheUnited Kingdom. Endorsementnotice ThetextoftheInternationalStandardISO47963:2000wasapprovedbyCENasaEuropean Standardwithoutanymodification. NOTE:Normativ

18、ereferencestoInternationalStandardsarelistedinannexZA(normative). ENISO47963:2000 Reference number ISO 4796-3:2000(E) INTERNATIONAL STANDARD ISO 4796-3 First edition 2000-04-01 Laboratory glassware Bottles Part 3: Aspirator bottles Verrerie de laboratoire Flacons Partie 3: Flacons tubulure basse ENI

19、SO47963:2000 ii ENISO47963:2000 ISO -69743:(0002)E iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees.

20、 Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Interna

21、tional Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies

22、 for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of ISO 4796 may be the subject of patent rights. ISO shall not be held responsible for identifyin

23、g any or all such patent rights. International Standard ISO 4796-3 was prepared by Technical Committee ISO/TC 48, Laboratory glassware and related apparatus, Subcommittee SC 2, General laboratory glassware (other than measuring apparatus). ISO 4796 consists of the following parts, under the general

24、title Laboratory glassware Bottles: Part 1: Screw-neck bottles Part 2: Conical neck bottles Part 3: Aspirator bottles ENISO47963:2000 ENISO47963:2000 INTENRATIONAL TSANDADR ISO -69743:(0002)E 1 Laboratory glassware Bottles Part 3: Aspirator bottles 1 Scope This part of ISO 4796 specifies a series of

25、 aspirator bottles with a screw neck or with a conical neck suitable for the delivery of liquid chemicals and reagents in general laboratory use. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of I

26、SO 4796. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 4796 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated belo

27、w. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 383:1976, Laboratory glassware Interchangeable conical ground joints. ISO 4796-1:2000, Laboratory glassware Bottles P

28、art 1: Screw-neck bottles. ISO 4796-2:2000, Laboratory glassware Bottles Part 2: Conical neck bottles. 3 Types and capacities 3.1 There are three types of aspirator bottles specified in this part of ISO 4796: type ASN: aspirator bottles with a screw neck; type ACS: aspirator bottles with a conical n

29、eck socket; type ACJ: aspirator bottles with an interchangeable conical ground joint. 3.2 The nominal capacities of aspirator bottles shall be chosen from the following series: 0,5 l 1 l 2 l 5 l 10 l and 20 l 3.3 The nominal capacity of an aspirator bottle indicates the quantity of liquid which a bo

30、ttle of average wall thickness shall contain when the bottle is filled to the turn of the shoulder. 3.4 The design of the bottle shall be such that the total capacity to the base of the neck shall be approximately 15 % greater than that to the shoulder. ENISO47963:2000 ISO -69743:(0002)E 2 4 Dimensi

31、ons The dimensions and tolerances of aspirator bottles are given in Figure 1 and in Tables 1 and 2 below. Table 1 Dimensions of aspirator bottles with a screw neck Nominal capacity Total height h 1 Height to shoulder h 2 Outside diameter d Wall thickness s l mm approx. mm approx. mm approx. mm min.

32、1 225 153 100 2,0 2 260 170 136 2,0 5 330 208 181 2,0 10 410 265 227 2,7 20 505 330 288 3,0 Table 2 Dimensions of aspirator bottles with a conical neck Nominal capacity Total height h 1 Outside diameter d Wall thickness s Neck socket a Ground joint at outlet l mm approx. mm approx. mm min. 0,5 162 8

33、6 1,3 24/29 19/26 1 198 107 1,7 29/32 19/26 2 246 133 2,0 29/32 19/26 5 318 181 2,0 45/40 29/32 10 398 227 2,7 60/46 29/32 20 492 288 3,0 60/46 29/32 a Or ground joint in accordance with ISO 383 (see 5.2.8 for details) 5 Construction 5.1 Material In accordance with 5.1 of ISO 4796-1:2000. 5.2 Design

34、 5.2.1 The base of the bottle shall be constructed so as to enable the bottle to stand firmly on a flat surface without rocking or spinning. ENISO47963:2000 ISO -69743:(0002)E 3 Dimensions in millimetres Key 1 Taper 1:30 Figure 1 Example of an aspirator bottle 5.2.2 The base of the bottle shall have

35、 a suitable radius in order to provide a smooth transition between the base and the side. The main portion of the side shall be slightly tapered with the smaller diameter at the base of the bottle. The diameter d and the heights h 1 and h 2 shall be as given in Tables 1 and 2. 5.2.3 The shoulder of

36、the bottle shall have a suitable radius so as to provide a smooth transition between the side and the conical upper proportion of the bottle. 5.2.4 The upper portion of the shoulder shall be of conical shape. The transition radius from the shoulder to the neck shall be as small as possible to be com

37、patible with good manufacturing practice. 5.2.5 The bottle shall be blown so as to evenly distribute the glass in the mould avoiding sudden changes in the wall thickness. The thinnest areas shall not have a thickness less than the minimum values specified in Table 1. ENISO47963:2000 ISO -69743:(0002

38、)E 4 5.2.6 The neck of the bottle shall be stoutly constructed and finished with a strengthening lip designed to facilitate pouring without liquid running down the outside of the bottle. A clip-on anti-drip ring of plastics material fitting into a slightly recessed channel on the outside of the neck

39、 is permitted as an alternative for aspirator bottles with a screw neck. NOTE There are suitable national standards for the dimensions and design of the thread of the screw neck. 5.2.7 The outer glass surface of the bottles may be coated with a suitable plastics material for protection and to limit

40、leakage of a liquid if the bottle is damaged. The coating shall be resistant to steam sterilization at 135 C. 5.2.8 The internal surface of the conical neck socket shall be smooth, suitable to fit with a rubber stopper, or shall be finished by fine grinding. If the surface is finished, the grinding

41、shall comply with the interchangeable conical ground joints specified in ISO 383 and dimensions specified in Table 2 of this part of ISO 4796. If the socket surface is smooth, the socket dimensions shall be suited for finishing by fine grinding so as to fit an interchangeable conical ground joint sp

42、ecified in Table 1. 5.2.9 The outlet in the side wall of the bottle shall have a distance of approximately 28 mm (see Figure 1) from the bottom. The outlet shall be supplied with an interchangeable ground joint, size 19/26 or 29/32 in accordance with ISO 383, or with an external screw thread, comply

43、ing with suitable national or International Standards. 5.3 Closure for aspirator bottles with a screw neck In accordance with 5.3 of ISO 4796-1:2000. 5.4 Stoppers for aspirator bottles with a conical neck In accordance with 5.3 of ISO 4796-2:2000. 6 Designation If a designation of bottles is require

44、d, this shall be by reference to this part of ISO 4796, i.e. ISO 4796-3, together with the nominal capacity of the bottle and the type specified in 3.1. EXAMPLE For a bottle with a nominal capacity of 2 l and of type ACS (aspirator bottle with a conical neck socket), the designation would be as foll

45、ows: Laboratory bottle ISO 4796-3 - 2 ACS 7 Marking In accordance with clause 7 of ISO 4796-1:2000. ENISO47963:2000 gaPe3 INESO7469:30020 AnnexZA (normative) Normativereferencestointernationalpublications withtheirrelevantEuropeanpublications ThisEuropeanStandardincorporatesbydatedorundatedreference

46、,provisionsfromother publications.Thesenormativereferencesarecitedattheappropriateplacesinthetextandthe publicationsarelistedhereafter.Fordatedreferences,subsequentamendmentstoorrevisions ofanyofthesepublicationsapplytothisEuropeanStandardonlywhenincorporatedinitby amendmentorrevision.Forundatedrefe

47、rencesthelatesteditionofthepublicationreferredto applies(includingamendments). NOTEWhereanInternationalPublicationhasbeenmodifiedbycommonmodifications, indicatedby(mod.),therelevantEN/HDapplies. Publication Year Title EN Year ISO47961 2000 LaboratoryglasswareBottlesPart1: Screwneckbottles ENISO47961 2000 ISO47962 2000 LaboratoryglasswareBottlesPart2: Conicalneckbottles ENISO47962 2000 ENISO47963:2000 BS EN ISO 4796-3:2001 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents th