BS EN 61754-9-2002 Fibre optic connector interfaces - Type DS connector family《光纤连接器接口 DS型连接器族》.pdf

《BS EN 61754-9-2002 Fibre optic connector interfaces - Type DS connector family《光纤连接器接口 DS型连接器族》.pdf》由会员分享，可在线阅读，更多相关《BS EN 61754-9-2002 Fibre optic connector interfaces - Type DS connector family《光纤连接器接口 DS型连接器族》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 61754-9:2001 Fibre optic connector interfaces Part 9: Type DS connector family The European Standard EN 61754-9:2001 has the status of a British Standard ICS 33.180.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 61754-9:2001 This British Standar

2、d, having been prepared under the direction of the Electrotechnical Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 20 March 2002 BSI 20 March 2002 ISBN 0 580 39111 6 National foreword This British Standard is the official Eng

3、lish language version of EN 61754-9:2001. It was derived by CENELEC from IEC 61754-9:1996. The CENELEC common modifications have been implemented at the appropriate places in the text and are indicated by common modification tags . The UK participation in its preparation was entrusted by Technical C

4、ommittee GEL/86, Fibre optics, to Subcommittee GEL/86/2, Fibre optic interconnecting devices, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. From 1 January 1997, all IEC publications have the number 60000 added to t

5、he old number. For instance, IEC 27-1 has been renumbered as IEC 60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normall

6、y include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International S

7、tandards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British St

8、andard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and Euro

9、pean developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 10, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amen

10、dments issued since publication Amd. No. Date CommentsEUROPEAN STANDARD EN 61754-9 NORME EUROPENNE EUROPISCHE NORM December 2001 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Se

11、cretariat: rue de Stassart 35, B - 1050 Brussels 2001 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61754-9:2001 E ICS 33.180.20 English version Fibre optic connector interfaces Part 9: Type DS connector family (IEC 61754-9:1996

12、, modified) Interface de connecteurs pour fibres optiques Partie 9: Famille de connecteur de type DS (CEI 61754-9:1996, modifie) Steckgesichter von Lichtwellenleiter- Steckverbindern Teil 2: Bauart DS Steckverbinderfamilie (IEC 61754-9:1996, modifiziert) This European Standard was approved by CENELE

13、C on 1997-03-11. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards

14、 may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified

15、 to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Swe

16、den, Switzerland and United Kingdom.Foreword The text of document 86B/837/FDIS, future edition 1 of IEC 61754-9, prepared by SC 86B, Fibre optic interconnecting devices and passive components, of IEC TC 86, Fibre optics, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as E

17、N 61754-9 on 1997-03-11 with a corrigendum to the text of the International Standard. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2002-07-01 latest date by which the natio

18、nal standards conflicting with the EN have to be withdrawn (dow) 2002-07-01 _ Page2 EN617549:2001 BSI20March2002CONTENTS Page Clause 1 Scope 4 2 Description 4 3 Interfaces 4 Page3 EN617549:2001 BSI20March2002FIBRE OPTIC CONNECTOR INTERFACES Part 9: Type DS connector family 1 Scope This part of IEC 1

19、754 defines the standard interface dimensions for type DS family of connectors. 2 Description The parent connector for type DS connector family is a single position plug connector which is characterized by a cylindrical, spring-loaded ferrule of a 2,5 mm nominal ferrule diameter. The optical alignme

20、nt mechanism of the connectors is of a rigid hole or a resilient sleeve style, and is self-contained within the jack connector. 3 Interfaces This standard contains the following standard interfaces. Interface 9-1 : Plug connector interface Interface 9-2 : Jack connector interface The type DS connect

21、or family is a connector set of a plug and a jack configuration, and is generally used as a plug-in type backplane connector. The plug is retained to a backplane connector housing which is mounted to a backplane. The jack is retained to a printed board housing which is fixed to a printed board. The

22、plug mates to the jack by plugging the printed board into the backplane. The plug of interface 9-1 and jack of interface 9-2 have a ferrule with a spherically polished ferrule endface, and make physical contact. The following standard interfaces are intermateable. Interface 9-1 mates with interface

23、9-2. Page4 EN617549:2001 BSI20March2002NOTES 1 Allowable thickness of the backplane is maximum 2,5 mm specification. 2 Dashed lines are for information only and represent the backplane, the housing and the outer surface of the plug. Figure 1 Plug connector interface Page5 EN617549:2001 BSI20March200

24、2Table 1a Dimensions of the plug connector interface Reference Dimension Notes Minimum Maximum A 1, see table 1b B 4,4 mm 4,45 mm C 5,9 mm 6,0 mm D 1,475 mm 1,675 mm 2 E 8,1 mm F 0,4 mm 0,6 mm 45 chamfer BF 10 mm 25 mm Radius, 3 BG 1,75 mm 2,26 mm Diameter BI 25 35NOTES 1 A chamfer or radius is allo

25、wed to a maximum depth of 1,2 mm from the ferrule endface. 2 The dimension D is given for a plug endface when not mated. It is noticed that the ferrule is movable by a certain axial compression force with direct contacting end faces, and therefore dimension D is variable. Ferrule compression force s

26、hall be from 7,8 N to 11,8 N when the position of the optical datum target from the datum X is moved in the range of 1,775 mm to 1,975 mm. 3 Dome eccentricity of the spherically polished ferrule endface shall be less than 50 m. Table 1b Grade Grade Dimension mm Notes Minimum Maximum 1 2,4985 2,4995

27、See note 2 2,4980 2,5000 See note NOTE Add grade number to the interface reference number. Page6 EN617549:2001 BSI20March2002NOTE Dashed lines are for information only and represent the housing and the outer surface of the jack. Figure 2a Jack connector interface Page7 EN617549:2001 BSI20March2002Ta

28、ble 2a Dimensions of the jack connector interface Reference Dimension Notes Minimum Maximum A See table 2b B 2,7 mm 2,8 mm C 4,33 mm 4,38 mm D 6,1 mm 6,2 mm E 7,9 mm 8,0 mm F 1,775 mm 1,975 mm G 1, See table 2c H 0,35 mm 0,55 mm 45 chamfer I 0,4 mm 0,6 mm 45 chamfer J 0,1 mm 0,3 mm 45 chamfer BF 10

29、mm 25 mm Radius, 2 BG 1,75 mm 2,26 mm Diameter BI 25 35 NOTES 1 A chamfer or a radius is allowed to a maximum depth of 1,2 mm from the ferrule endface. 2 Dome eccentricity of the spherical polished endface shall be less than 50 m. Table 2b Alignment device grade Reference Dimension mm Notes Minimum

30、Maximum 1 Resilient sleeve, 1 and 2 2 Resilient sleeve, 1 and 2 NOTES 1 The connector alignment feature is a resilient alignment sleeve. The feature must accept a gauge pin to a depth of 7 mm with a force of 2 N to 5,9 N under the condition that another gauge pin is inserted into the feature from th

31、e other side. 2 Add grade number to the interface reference number. Table 2c Ferrule grade Grade Dimension mm Notes Minimum Maximum 1 2,4985 2,4995 See note 2 2,4980 2,5000 See note NOTE Add grade number to the interface reference number. Page8 EN617549:2001 BSI20March2002CN CL CK C or R IEC 1 109/9

32、6 Figure 2b Pin gauge for resilient alignment sleeve Table 2d Dimensions of the pin gauge for resilient alignment sleeve Reference Dimension mm Notes Minimum Maximum CK 2,4985 2,4995 Surface roughness R z = 0,2 m CL 2,8 4,8 CN 7 15 Page9 EN617549:2001 BSI20March2002National annex NA (informative) Or

33、iginal IEC text amended by CENELEC common modifications The text of the International Standard IEC 61754-9:1996 was approved by CENELEC as a European Standard with the following corrigendum to IEC 61754-9: Table 2d Replace “Surface roughness grade N4 (0,2 m radius)“ by “Surface roughness R z= 0,2 m“

34、. Page10 BSEN617549:2001 BSI20March2002BS EN 61754-9:2001 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is

35、incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if

36、 anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating

37、service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: orders

38、bsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a

39、wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0

40、)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 70

41、02. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publicati

42、ons. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photo

43、copying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.