BS EN 60684-3-165-2004 Flexible insulating sleeving - Specifications for individual types of sleeving - Extruded Polyolefin flame retarded limited fire hazard sleeving《绝缘软套管 各种型号软套.pdf

《BS EN 60684-3-165-2004 Flexible insulating sleeving - Specifications for individual types of sleeving - Extruded Polyolefin flame retarded limited fire hazard sleeving《绝缘软套管 各种型号软套.pdf》由会员分享，可在线阅读，更多相关《BS EN 60684-3-165-2004 Flexible insulating sleeving - Specifications for individual types of sleeving - Extruded Polyolefin flame retarded limited fire hazard sleeving《绝缘软套管 各种型号软套.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 60684-3-165: 2004 Flexible insulating sleeving Part 3: Specifications for individual types of sleeving Sheet 165: Extruded polyolefin, flame retarded, limited fire hazard sleeving The European Standard EN 60684-3-165:2004 has the status of a British Standard ICS 29.035.20 BS E

2、N 60684-3-165:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 9 August 2004 BSI 9 August 2004 ISBN 0 580 44233 0 National foreword This British Standard is the official English language version of EN 60684-3-165:2004. It is identical wit

3、h IEC 60684-3-165:2004. The UK participation in its preparation was entrusted by Technical Committee GEL/15, Insulating material, to Subcommittee GEL/15/3, Material specifications, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to

4、 its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electro

5、nic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to und

6、erstand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document compri

7、ses a front cover, an inside front cover, the EN title page, pages 2 to 8, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEAN STANDARD EN 60684-3-16

8、5 NORME EUROPENNE EUROPISCHE NORM July 2004 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2004 CENELEC - All rights of exploit

9、ation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60684-3-165:2004 E ICS 29.035.20 English version Flexible insulating sleeving Part 3: Specifications for individual types of sleeving Sheet 165: Extruded polyolefin, flame retarded, limited fire hazard sleeving (I

10、EC 60684-3-165:2004) Gaines isolantes souples Partie 3: Spcifications pour types particuliers de gaines Feuille 165: Gaines en polyolfine extrudes, retardes la flamme, rsistance au feu limite (CEI 60684-3-165:2004) Isolierschluche Teil 3: Anforderungen fr einzelne Schlauchtypen Blatt 165: Extrudiert

11、e Polyolefinschluche, flammwidrig, mit verbessertem Verhalten im Brandfall (IEC 60684-3-165:2004) This European Standard was approved by CENELEC on 2004-07-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standa

12、rd the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, Frenc

13、h, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, C

14、yprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 68604-3-61:50024 - - 2 Foreword The text of

15、document 15C/1598/FDIS, future edition 1 of IEC 60684-3-165, prepared by SC 15C, Specifications, of IEC TC 15, Insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60684-3-165 on 2004-07-01. The following dates were fixed: latest date by which the EN

16、 has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2005-04-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2007-07-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of

17、the International Standard IEC 60684-3-165:2004 was approved by CENELEC as a European Standard without any modification. _ Page2 EN606843165:2004066-48-3165 EI2:C400 9 FLEXIBLE INSULATING SLEEVING Part 3: Specifications for individual types of sleeving Sheet 165: Extruded polyolefin, flame retarded,

18、 limited fire hazard sleeving 1 Scope This standard gives the requirements for two types of extruded polyolefin, flame retarded, limited fire hazard sleeving. Type A: Thin wall Internal diameter up to 30 mm Type B: Thick wall Internal diameter up to 30 mm These sleevings are normally supplied in the

19、 following colours: black, red, green, blue, white and yellow. These sleevings are for use up to temperatures of 90 C. Sizes or colours other than those listed in this standard may be available as custom items. These items are considered to comply with this standard if they comply with the requireme

20、nts listed in Tables 2, 3, and 4, excluding dimensions. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in tha

21、t application and not based on this specification alone. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (incl

22、uding any amendments) applies. IEC 60684-1:2003, Flexible insulating sleeving Part 1: Definitions and general requirements IEC 60684-2:1997, Flexible insulating sleeving Part 2: Methods of test IEC 60757:1983, Codes for designation of colours ISO 1817:1999, Rubber, vulcanized Determination of the ef

23、fect of liquids Page3 EN606843165:2004066-48-3165 EI2:C400 11 3 Designation This sleeving shall be identified by the following designation: Description IEC publication number IEC part number IEC sheet number TypeSize (nominal internal diameter, in mm) Colour Sleeving IEC 60684 - 3 - 165 - A - 10 - G

24、N Any colour abbreviations shall comply with IEC 60757. Where no abbreviation is given, the colour shall be written in full. 4 Requirements In addition to the general requirements given in IEC 60684-1, the sleeving shall comply with the requirements set out in Tables 1, 2, 3, and 4. 5 Sleeving confo

25、rmance Conformance to the requirements of this specification shall normally be based on the results from 10 mm internal diameter black sleeving for Type A and B. The colour fastness to light shall be determined for all colours. Table 1 Dimensional requirements for Types A and B Type A Type B Wall th

26、ickness mm Wall thickness mm Nominal internal diameter mm Tolerance on internal diameter mm Nominal Tolerance Nominal Tolerance 1,0 1,5 2,0 2,5 3,0 4,0 5,0 8,0 10,0 12,0 16,0 20,0 25,0 30,0 0,15 0,15 0,15 0,15 0,15 0,25 0,25 0,25 0,5 0,5 0,5 0,5 0,5 0,5 0,25 0,25 0,25 0,25 0,25 0,25 0,25 0,25 0,30 0

27、,35 0,35 0,35 0,45 0,55 0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,5 0,5 0,5 0,5 0,5 0,5 0,5 0,65 0,65 0,65 0,85 0,85 0,85 0,85 0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,1 Page4 EN606843165:2004066-48-3165 EI2:C400 31 Table 2 Property requirements Property IEC 60684-2 Clau

28、se or subclause Units Max. or min. Requirements Remarks Dimensions Internal diameter Wall thickness 3 3.1.2 3.3.2 mm mm Table 1 Table 1 Density 4 g/cm 3Max. 1,6 Bending at low temperature 14 - - No cracking shall be visible Condition at 40 C 2 K. For strips, the mandrel shall be no more than 20X the

29、 wall thickness. Full section sleeving is tested unfilled and the mandrel shall be no more than 20X the outer diameter Tensile strength Elongation at break 19.1 and 19.2 19.1 and 19.2 MPa % Min. Min. 10 175 Use a jaw separation rate of 250 mm/min Below 8,0 mm internal diameter, test as sleeving At 8

30、 mm internal diameter and above as dumb-bells Breakdown voltage 21 kV Min. Table 3 Flame propagation 26 Method A s Max. 60 In addition, the indicator flag shall not be burnt and the cotton shall not be ignited Volume resistivity - at room temperature - after damp heat 23 23.4.2 23.4.4 m m Min. Min.

31、10 1110 10 Oxygen index - at ambient temperature - at elevated temperature 27 27.1 27.2 % C Min. Min. 29 250 Colour fastness to light Standard identification number 34 Min. The colour standard contrast between the exposed and unexposed parts of the specimen shall be equal to, or less than, that of t

32、he fastness standard Fastness standard 4 Resistance to selected fluids Tensile strength Elongation at break 36 19.1 and 19.2 19.1 and 19.2 MPa % Min. Min. 5 100 Use the fluids and test temperatures specified in Table 4 Page5 EN606843165:2004066-48-3165 EI2:C400 51 Table 2 (continued) Property IEC 60

33、684-2 Clause or subclause Units Max. or min. Requirements Remarks Heat ageing Tensile strength Elongation at break 39 19.1 and 19.2 19.1 and 19.2 MPa % Min. Min. 5 100 Heat at 100 C 3 K Smoke index 43 - Max. 20 Toxicity index 44 - Max. 5 Halogen content 45 45.1 45.2 % % Max. Max. 0,2 0,1 Acid gas ge

34、neration 46 46.2 pH pH S/mm Min. Max. Max. 3,5 10,5 10,0 Long term ageing Elongation 50 19.1 and 19.2 % Min. 100 The ageing temperature shall be 90 C 2 K The breakdown voltage shall be determined by any of the methods described in 21.2, 21.3 or 21.4 of IEC 60684-2. The central value shall comply wit

35、h the minimum value in Table 3 below. The rate of application of the voltage shall be 500 V/s. Table 3 Requirements for breakdown voltage Nominal wall thicknessamm Breakdown voltage Min. kV 0,25 0,35 3,0 0,45 0,55 4,0 0,65 0,75 5,0 0,85 0,95 6,0 aFor non-standard wall thicknesses, the breakdown volt

36、age shall be at least that of the next smaller standard wall thickness. Page6 EN606843165:2004066-48-3165 EI2:C400 71 Table 4 Resistance to selected fluids Fluids Type Standard or symbol Immersion temperature C 2 K Gasoline ISO 1817 Liquid B 23 Fuels Kerosene ISO 1817 Liquid F 23 Phosphate base ISO

37、1817 Fluid 103 23 Silicone base S-1714* 23 Hydraulic fluids Mineral base H-520* 23 Synthetic base ISO 1817 Liquid 101 23 Mineral base ISO1817 Oil no. 2 23 Mineral base O-1176* 23 Oils Mineral base O-142* 23 Isopropyl alcohol 23 Propanol 25 % White spirit 75 % 23 Cleaning fluids Solvent Methylethylke

38、tone 23 Runway de-icers Inhibited potassium acetate 50 %. Water 50 % 23 De-icing fluids Aircraft de-icers Ethylene glycol 80 % Water 20 % 23 * These are commercially available fluids which can be identified in aviation fluid guides. NOTE Other fluids and/or temperatures may be specified for customer

39、s with specific needs. These additional fluids and/or temperatures shall be applicable when incorporated into agreements between the supplier and the customer. _ Page7 EN606843165:2004 - - 3 EN 68604-3-61:50024 Annex ZA (normative) Normative references to international publications with their corres

40、ponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE Where an inter

41、national publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60684-1 2003 Flexible insulating sleeving Part 1: Definitions and general requirements EN 60684-1 2003 IEC 60684-2 1997 Part 2: Methods of test EN 606

42、84-2 1997 IEC 60757 1983 Code for designation of colours HD 457 S1 1985 ISO 1817 1999 Rubber, vulcanized - Determination of the effect of liquids - - Page8 EN606843165:2004blankBS EN 60684-3-165: 2004 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent n

43、ational body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they posses

44、s the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity

45、of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international

46、 and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the

47、BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI elec

48、tronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can b