BS EN 603-2-1997 Aluminium and aluminium alloys - Wrought forging stock - Mechanical properties《铝及铝合金 锻坯 机械性能》.pdf

《BS EN 603-2-1997 Aluminium and aluminium alloys - Wrought forging stock - Mechanical properties《铝及铝合金 锻坯 机械性能》.pdf》由会员分享，可在线阅读，更多相关《BS EN 603-2-1997 Aluminium and aluminium alloys - Wrought forging stock - Mechanical properties《铝及铝合金 锻坯 机械性能》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 603-2 : 1997 The Eu

2、ropean Standard EN 603-2 : 1996 has the status of a British Standard ICS 77.150.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Aluminium and aluminium alloys Wrought forging stock Part 2. Mechanical propertiesBS EN 603-2 : 1997 This British Standard, having been prepared u

3、nder the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 May 1997 BSI 1997 The following BSI references relate to the work on this standard: Committee reference NFE/35 Draft for comment 91/49165 DC ISBN 0 580 27136 6 Ame

4、ndments issued since publication Amd. No. Date Text affected Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee NFE/35, Light metals and their alloys, upon which the following bodies were represented: Aluminium Federation Al

5、uminium Stockholders Association Association of Light Alloy Refiners Limited Magnesium Industry Council Ministry of Defence The following bodies were also represented in the drafting of the standard, through subcommittees and panels: Association of British Welded Aluminium Tube Makers Institution of

6、 Structural Engineers Metal Packaging Manufacturers AssociationBS EN 603-2 : 1997 BSI 1997 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Text of EN 603-2 3ii BSI 1997 BS EN 603-2 : 1997 National foreword This British Standard has been prepared by Technical

7、 Committee NFE/35 and is the English language version of EN 603-2 : 1996, Aluminium and aluminium alloys Wrought forging stock Part 2: Mechanical properties published by the European Committee for Standardization (CEN). Cross-references Publications referred to Corresponding British Standards EN 515

8、 BS EN 515 : 1993 Aluminium and aluminium alloys Wrought products Temper designations EN 573-3 BS EN 573 Aluminium and aluminium alloys Chemical composition and form of wrought products Part 3: 1995 Chemical composition EN 603-1 BS EN 603 Aluminium and aluminium alloys Wrought forging stock Part 1:

9、Technical conditions for inspection and delivery EN 603-3 BS EN 603 Aluminium and aluminium alloys Wrought forging stock Part 3: Tolerances on dimensions and form EN 10002-1 BS EN 10002 Tensile testing of metallic materials Part 1: 1990 Method of test at ambient temperature EN 10204 BS EN 10204 : 19

10、91 Metallic products Types of inspection document ISO 468 BS 1134 Assessment of surface texture Part 1: 1988 Methods and instrumentation This Part of BS EN 603, together with BS EN 515, BS EN 573-3, BS EN 573-4, BS EN 586-2, BS EN 603-1 and EN 604-1 partially supersedes BS 1472 : 1972. When prEN 586

11、-1 is published, BS 1472 : 1972 will be withdrawn. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 6, an inside back cover and a

12、back cover.CEN European Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1996 Copyright reserved to CEN members Ref. No. EN 603-2 : 1996 E EUROPEAN STANDARD EN 603-2 NORME EUROPE ENNE EUROPA IS

13、CHE NORM September 1996 ICS 77.120.10 Descriptors: Aluminium products, aluminium alloys, rolled products, forgings, mechanical properties, acceptance testing, user supplier relations English version Aluminium and aluminium alloys Wrought forging stock Part 2: Mechanical properties Aluminium et allia

14、ges daluminium Produits corroye s destine sa la forge Partie 2: Caracte ristiques me caniques Aluminium und Aluminiumlegierungen Stranggepretes oder gewalztes Schmiedevormaterial Teil 2: Mechanische Eigenschaften This European Standard was approved by CEN on 1996-08-16. CEN members are bound to comp

15、ly with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Sec

16、retariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the off

17、icial versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.Page 2 EN 603-2 : 1996 BSI 1997 Foreword This European Stand

18、ard has been prepared by Technical Committee CEN/TC 132, Aluminium and aluminium alloys, the Secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 1997, and

19、conflicting national standards shall be withdrawn at the latest by March 1997. Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 3, Forgings and cast and wrought forging stock, to prepare the following standard: EN 603-2 Aluminium and aluminium alloys Wrought forgi

20、ng stock Part 2: Mechanical properties This standard is part of a set of three standards. The other standards deal with: EN 603-1 Aluminium and aluminium alloys Wrought forging stock Part 1: Technical conditions for inspection and delivery EN 603-3 Aluminium and aluminium alloys Wrought forging stoc

21、k Part 3: Tolerances on dimensions and form According to the CEN/CENELEC Internal Regulations, the national standards bodies of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Iceland, Italy, Luxembourg, Netherlands, Norway,

22、 Portugal, Spain, Sweden, and the United Kingdom. Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Definitions 3 4 Tensile testing 3 5 Mechanical properties 3 6 Electrical conductivity 3 Annex A (normative) Rules for rounding 6Page 3 EN 603-2 : 1996 BSI 1997 1 Scope This Part of EN 603

23、specifies the mechanical properties of wrought forging stock in aluminium and aluminium alloys for general engineering applications. The chemical composition and temper designations for these alloys are specified in EN 573-3 and EN 515 respectively. 2 Normative references This European Standard inco

24、rporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this Eur

25、opean standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 515 Aluminium and aluminium alloys Wrought products Temper designations EN 573-3 Aluminium and aluminium alloys Chemical composition and form of

26、wrought products Part 3: Chemical composition EN 603-1 Aluminium and aluminium alloys Wrought forging stock Part 1: Technical conditions for inspection and delivery EN 2004-1 Aerospace series Test methods for aluminium and aluminium alloy products Part 1: Determination of electrical conductivity of

27、wrought aluminium alloys EN 10002-1 Metallic materials Tensile testing Part 1: Method of test (at ambient temperature) 3 Definitions For the purposes of this standard the following definition applies: 3.1 section size The minor sectional dimension, i.e. diameter for extruded round bar, width across

28、flats for extruded square bar and thickness for extruded rectangular section, designated t. 4 Tensile testing For the selection of specimens and preparation of test pieces, see EN 603-1. Tensile testing shall be carried out in accordance with EN 10002-1. 5 Mechanical properties 5.1 Extruded forging

29、stock Extruded forging stock is normally supplied in the F or H112 temper condition. Testing to determine mechanical properties of extruded forging stock shall be undertaken only when requested by the purchaser and specified on the order (see EN 603-1). In instances where tensile testing is specifie

30、d on extruded forging stock in heat treatable alloys, the specimen selected for test shall be heat treated in accordance with the recommended practice for the temper condition of final use. The mechanical properties of aluminium alloys are specified in tables 1 to 6. Test results shall be rounded in

31、 accordance with the rules given in annex A. For section sizes greater than those quoted, the levels of mechanical properties shall be as agreed between purchaser and supplier. 5.2 Rolled forging stock Mechanical properties for rolled forging stock shall be subject to agreement between purchaser and

32、 supplier. 6 Electrical conductivity The electrical conductivity of extruded forging stock produced in alloy EN AW-7075 in the T732 temper condition shall be determined in accordance with EN 2004-1, as part of the inspection lot acceptance, by testing the surface of the previously selected tensile t

33、est specimen to the criteria shown in table 6.Page 4 EN 603-2 : 1996 BSI 1997 Table 1. Alloy EN AW-2014 (Al Cu4SiMg) Product Temper Section size t Tensile strength R m Proof stress R p0,2 Elongation A MPa MPa % mm min. min. min. Extruded T42 All sizes 370 210 11 T62 t# 180 440 380 6 Table 2. Alloy E

34、N AW-2024 (Al Cu4Mg1) Product Temper Section size t Tensile strength R m Proof stress R p0,2 Elongation A MPa MPa % mm min. min. min. Extruded T42 t# 150 420 260 8 Table 3. Alloy EN AW-5083 (Al Mg4, 5Mn0,7) Product Temper Section size t Tensile strength R m Proof stress R p0,2 Elongation A MPa MPa %

35、 mm min. min. min. Extruded H112 t# 150 270 110 12 Table 4. Alloy EN AW-5754 (Al Mg3) Product Temper Section size t Tensile strength R m Proof stress R p0,2 Elongation A MPa MPa % mm min. min. min. Extruded H112 t# 150 180 80 14 Table 5. Alloy EN AW-6082 (Al SiMgMn) Product Temper Section size t Ten

36、sile strength R m Proof stress R p0,2 Elongation A MPa MPa % mm min. min. min. Extruded T62 t# 200 310 260 7Page 5 EN 603-2 : 1996 BSI 1997 Table 6. Alloy EN AW-7075 (Al Zn5, 5MgCu) Product Temper Section size t Tensile strength R m Proof stress R p0,2 Elongation A MPa MPa % mm min. min. min. Extrud

37、ed T62 t# 100 510 430 7 T732 1) t# 100 455 385 6 1) For inspection lot acceptance purposes, extruded forging stock in T732 temper shall comply with the following criteria when tested on the previously selected tensile test specimen. Electrical conductivity (g) MS/m Level of mechanical properties Lot

38、 acceptance status g$23,2 per specified requirements acceptable 22,0#g23,2 per specified requirements and R p0,2 does not exceed minimum specified in the standard by more than 85 MPa acceptable 22,0#g 23,2 per specified requirements but R p0,2 exceeds minimum specified in the standard by more than 8

39、5 MPa suspect (see note) g 22,0 any level unacceptable NOTE. When the lot acceptance status is found to be suspect, the specimen shall be reprocessed or subjected to a heat treatment for not less than 30 min at (465 5) C and quenched into cold water. Electrical conductivity shall then be measured wi

40、thin 15 min of quenching. If the difference between this measurement and the original measurement on the specimen is 3,5 MS/m or more, the inspection lot is acceptable. If the difference is less than 3,5 MS/m the inspection lot is unacceptable.Page 6 EN 603-2 : 1996 BSI 1997 Annex A (normative) Rule

41、s for rounding In recording test results, the number representing the result of a test to determine a given property shall be expressed to the same number of decimal places as the corresponding number in this European Standard. The following rounding rules shall be used for determination of complian

42、ce with this standard: a) When the figure immediately after the last figure to be retained is less than 5, the last figure to be retained remains unchanged; b) When the figure immediately after the last figure to be retained is greater than 5, or equal to 5 and followed by at least one figure other

43、than zero, the last figure to be retained is increased by one; c) When the figure immediately after the last figure to be retained is equal to 5 and followed by zeros only, the last figure to be retained remains unchanged if even and is increased by one if odd. BSI 1997 BS EN 603-2 : 1997 List of re

44、ferences See national foreword.BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

45、| | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by

46、 amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Stand

47、ard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest e

48、ditions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those

49、that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards d