BS EN 1395-3-2007 Thermal spraying - Acceptance inspection of thermal spraying equipment - Arc spraying《热喷涂 热喷涂设备的验收检验 电弧喷涂》.pdf

《BS EN 1395-3-2007 Thermal spraying - Acceptance inspection of thermal spraying equipment - Arc spraying《热喷涂 热喷涂设备的验收检验 电弧喷涂》.pdf》由会员分享，可在线阅读，更多相关《BS EN 1395-3-2007 Thermal spraying - Acceptance inspection of thermal spraying equipment - Arc spraying《热喷涂 热喷涂设备的验收检验 电弧喷涂》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58equipment Part 3: Arc sprayingThe European Standard EN 1395-3:2007 has the status of a British Stan

2、dardICS 25.220.20Thermal spraying Acceptance inspection of thermal spraying BRITISH STANDARDBS EN 1395-3:2007BS EN 1395-3:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 February 2007 BSI 2007ISBN 978 0 580 50279 8Amendments issued sin

3、ce publicationAmd. No. Date Commentssecretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations. National forewordThis British Sta

4、ndard was published by BSI. It is the UK implementation of EN 1395-3:2007. This standard together with BS EN 1395-1, BS EN 1395-2, BS EN 1395-4, BS EN 1395-5, BS EN 1395-6 and BS EN 1395-7 supersedes BS EN 1395:1996.The UK participation in its preparation was entrusted to Technical Committee STI/40,

5、 Thermally sprayed inorganic finishes.A list of organizations represented on STI/40 can be obtained on request to its EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 1395-3January 2007ICS 25.220.20 Supersedes EN 1395:1996 English VersionThermal spraying - Acceptance inspection of thermal sprayinge

6、quipment - Part 3: Arc sprayingProjection thermique - Contrle dacceptation du matrielde projection thermique - Partie 3: Projection larcThermisches Spritzen - Abnahmeprfungen fr Anlagenzum thermischen Spritzen - Teil 3: LichtbogenspritzenThis European Standard was approved by CEN on 23 December 2006

7、.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on ap

8、plication to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre

9、has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Por

10、tugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means r

11、eservedworldwide for CEN national Members.Ref. No. EN 1395-3:2007: EEN 1395-3:2007 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Principles of acceptance inspection4 5 Procedure of acceptance inspection.5 6 Designation 5 7 Inspection report5 Annex A (i

12、nformative) Inspection report for arc spraying equipment (initial test/retest)6 Bibliography 8 EN 1395-3:2007 (E) 3 Foreword This document (EN 1395-3:2007) has been prepared by Technical Committee CEN/TC 240 “Thermal spraying and thermally sprayed coatings”, the secretariat of which is held by DIN.

13、This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2007, and conflicting national standards shall be withdrawn at the latest by July 2007. This document together with EN 1395-1, 1395-2, 1395-4,

14、1395-5, 1395-6 and 1395-7 supersedes EN 1395:1996. EN 1395 consists of the following Parts, under the general title Thermal spraying Acceptance inspection of thermal spraying equipment: Part 1: General requirements; Part 2: Flame spraying including HVOF; Part 3: Arc spraying; Part 4: Plasma spraying

15、; Part 5: Plasma spraying in chambers; Part 6: Manipulator systems; Part 7: Powder feed systems. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech

16、 Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 1395-3:2007 (E) 4 1 Scope This European Standar

17、d specifies requirements for the acceptance inspection of thermal spraying equipment, in this case arc spraying, used to produce thermally sprayed coatings of reproducible quality. This part should be used in conjunction with EN 1395-1, which includes general requirements and explanations of procedu

18、res. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 657:2005, Thermal

19、spraying Terminology, classification EN ISO 14919:2001, Thermal spraying Wires, rods and cords for flame and arc spraying Classification Technical supply conditions (ISO 14919:2001) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 657:2005 apply. 4 Pri

20、nciples of acceptance inspection 4.1 General The following clauses reveal state of the art technology in thermal spraying equipment and the minimum requirements concerning a stable parameter setting and maintenance as given in Annex A. 4.2 Atomising gas The atomising gas hoses and the control device

21、 shall be designed in such a manner that an undisturbed operation is ensured. 4.3 Arc spraying nozzle The nozzle system (contact tubes and air nozzle) shall permit a constant arc to be maintained and provide atomisation without causing deposits that might disturb the operation. 4.4 Spraying wire fee

22、d unit A continuously controllable and reproducible feed of the wires shall be provided. A precondition for this is an adequate constant air pressure and supply of electrical power. EN 1395-3:2007 (E) 5 5 Procedure of acceptance inspection 5.1 General Spraying equipment shall be deemed to have been

23、properly supplied for all suitable spraying applications and for use with all suitable spraying materials required for the spraying process if it complies with the following requirements: 5.2 Electrical power and wire feed unit Proof of the power rating required for continuous operation and of compl

24、iance of the feed unit with the requirements as specified in 4.4 shall be deemed to have been provided if: no deviations of the adjusted electrical values of more than 5 % or other disturbances due to an increased thermal loading occur; and system is operating at a maximum capacity for 10 min with a

25、 coating material with a suitable diameter: 1) anti-corrosion arc spraying system: zinc aluminium alloy, thermal spray material according to EN ISO 14919:2001, 2.3, or 2) engineering application arc spraying system: pure copper, thermal spray material according to EN ISO 14919:2001, 4.1. 5.3 Atomisi

26、ng gas The equipment shall be deemed to comply with the requirements of 4.2 if the atomising gas pressure indication does not deviate by more than 5 % from the set point over a 10 min period of spraying. 5.4 Arc spraying nozzle The nozzle system shall be deemed to comply with the requirements given

27、in 4.3 if, after testing according to 4.4, no disturbances occur in the arc and no disturbing deposits have been built up on the nozzle system by more or less molten spraying material. 6 Designation Acceptance inspection of the thermal spraying equipment for arc spraying shall be designated as follo

28、ws: Acceptance inspection according to EN 1395-3. 7 Inspection report An example for the inspection report is given in Annex A. EN 1395-3:2007 (E) 6 Annex A (informative) Inspection report for arc spraying equipment (initial test/retest) The initial test/retest fulfils the requirements of the accept

29、ance inspection according to EN 1395-3. User:. Manufacturer:. Year of manufacture: . Type of equipment: Type of spraying gun: . Spraying wire used for testing . Diameter: mm CE-documentation complete: yes / no Change after 10 minute continuous testing Evaluation actual value Item tested, where appli

30、cable Full scale Set point min. max. maximum deviation in % Limit in % passed failed Current A 5 Electrical power Voltage V 5 Pressure bar 5 Atomising gas Flow Nl/min1) 5 Wire feed Speed m/min 5 Flow l/min 10 Cooling water temperature to spraying gun C 10 C 1)Referred to temperature 0 C and normal p

31、ressure (1 013,25 hPa). EN 1395-3:2007 (E) 7 Deposits: yes / no Nozzle disturbance: yes / no Time needed for stabilisation: . Automatic energy shutdown: Lack of gas: yes / no Lack of cooling water: yes / no Excessive variations in feed: yes / no Limits of error of measuring instruments: % of set poi

32、nt (max. 5 %) Class 2,5 2): yes / no Comments: . The thermal spraying equipment has been accepted: yes / no Date: Inspectors signature: Date: Customers signature: . Date: Suppliers signature: 2)Maximum permissible error expressed by percentage of measuring span. EN 1395-3:2007 (E) 8 Bibliography 1 E

33、N 1395-1, Thermal spraying Acceptance inspection of thermal spraying equipment Part 1: General requirements blankBS EN BSI389 Chiswick High RoadLondonW4 4AL1395-3:2007BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK

34、 view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve t

35、he quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax:

36、 +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:

37、 +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless o

38、therwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products

39、 and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits

40、contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.Co

41、pyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted

42、 in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.