BS EN 1155-1997 Building hardware - Electrically powered hold-open devices for swing doors - Requirements and test methods《建筑五金 旋转门用电控器 试验方法和要求》.pdf

《BS EN 1155-1997 Building hardware - Electrically powered hold-open devices for swing doors - Requirements and test methods《建筑五金 旋转门用电控器 试验方法和要求》.pdf》由会员分享，可在线阅读，更多相关《BS EN 1155-1997 Building hardware - Electrically powered hold-open devices for swing doors - Requirements and test methods《建筑五金 旋转门用电控器 试验方法和要求》.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58swing doors Requirements and test methodsThe European Standard EN 1155:1997, with the incorporation

2、 of amendment A1:2002, has the status of a British StandardICS 91.190Building hardware Electrically powered hold-open devices for BRITISH STANDARDBS EN 1155:1997Incorporating Amendment No. 1 and Corrigendum Nos. 1, 2 and 3BS EN 1155:1997This British Standard, having been prepared under the direction

3、 of the Sector Board for Building and Civil Engineering, was published under the authority of the Standards Board and comes into effect on 15 September 1997 BSI 2006ISBN 0 580 28341 0obligations.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2

4、to 23 and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date Comments14075 20 February 2003 See revised national foreword14400 Corr. No. 113 March 2003 National foreword corrected14492 Corr. No

5、. 223 May 2003 Corrections to 7.2.1, 7.2.8, 7.2.8.2 and 7.2.1016311 Corr. No. 331 August 2006 Corrections to clause 8 and ZA.3The Commission in consultation with Member States have agreed a transition period for the co-existence of “harmonized” European Standards and their corresponding national sta

6、ndard(s). It is intended that this period will comprise a period, usually nine months, after the date of availability of the European Standard, during which any required changes to national regulations are to be made, followed by a further period, usually twelve months, for the implementation of CE

7、marking. At the end of this co-existence period, the national standard(s) will be withdrawn.Since BS EN 1155:1997 is the current national standard the changes introduced by amendment no. 1 may be implemented from nine months after publication.Based on this nominal transition period of twenty-one mon

8、ths, BS EN 1155:1997 (as amended) would be fully effective in September 2004.NOTE This date is approximate. Users of this standard should contact BSI Customer Services for confirmation of withdrawal.The UK participation in its preparation was entrusted by Technical Committee B/538, Doors, windows, s

9、hutters, hardware and curtain walling, to Subcommittee B/538/4, Building hardware, which has the responsibility to: aid enquirers to understand the text; present to the responsible/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; mo

10、nitor related international and European developments and promulgate them in the UK.A list of organizations represented on this committee can be obtained on request to its Secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this docum

11、ent may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. U

12、sers are responsible for its correct application.Compliance with a British Standard does not of itself confer immunity from legal National forewordThis British Standard is the official English language version of EN 1155:1997, including amendment A1:2002 and corrigendum February 2006, published by t

13、he European Committee for Standardization (CEN).The start and finish of text introduced or altered by CEN amendment A1 is indicated in the text by tags !“.EN 1155:1997 (as amended) is a candidate “harmonized” European Standard and fully takes into account the requirements of the European Commission

14、mandate M/101, Doors, windows, shutters, gates and related hardware, given under the EU Construction Products Directive (89/106/EEC), and intended to lead to CE marking. The date of applicability of EN 1155:1997 (as amended) as a “harmonized” European Standard, i.e. the date after which this standar

15、d may be used for CE marking purposes, is subject to an announcement in the Official Journal of the European Communities.EUROPISCHE NORMICS 91.190Descriptors: Har finitions, classifications, sp tance, markingBuilding hardware Electrically powered hold-open devices for swing doors RequQuincaillerie r

16、etenue lectbattantes Pres(inclut lamendemch ardizationComit Europen de NormalEuropisches Komitee fr NormungCentral Secretariat: rue de Stassart 3 1997 CEN All rights of exploitation in any form and by anynational members.isation6, B-1050 Brusselsmeans reserved worldwide for CEN Ref. No. EN 1155:1997

17、 + A1:2002 ECENEuropean Committee for StandThis European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same statu

18、s as the official versions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.amendment A1 was approved by CEN

19、on 2002-11-07. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such national standards may be

20、 obtained on application to the Central Secretariat or to any CEN member.dware, buildings, doors, fire doors, door closing devices, stopping devices, electromagnetic equipment, deecifications, performance evaluation, installation, tests, fatigue tests, performance tests, corrosion resisEnglish versi

21、onirements and test methods(includes amendment A1:2002)pour le btiment Dispositifs de romagntique pour portes criptions et mthodes dessai ent A1:2002)Schlsser und Baubeschlge Elektrisbetreibene Festellvorrichtungen fr Drehflgeltren Anforderungen und Prfverfahren (enthlt nderung A1:2002)This European

22、 Standard was approved by CEN on 1997-04-06 and May 1997+ A1December 2002EUROPEAN STANDARDNORME EUROPENNEEN 1155EN 1155:1997ForewordThis European Standard has been prepared by Technical Committee CEN/TC 33, Doors, windows, shutters, building hardware and curtain walling, the Secretariat of which is

23、held by AFNOR.This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of the EU Directive (89/106/EEC).For relationship with EU Directive 89/106/EEC, see informative Annex ZA which is an inte

24、gral part of the document.Whatever reference is made to classes, they are considered to be technical classes and not classes according to Article 3(2) of the Construction Products Directive (89/106/EEC).This European Standard is part of a package of European Standards dedicated to building hardware

25、products, and derives from performance requirements contained in various texts cited in Annex C.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 1997, and conflicting national standards sh

26、all be withdrawn at the latest by November 1997.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Irel

27、and, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.Foreword to amendment A1This document EN 1155:1997/A1:2002 has been prepared by Technical Committee CEN /TC 33, Doors, windows, shutters, building hardware and curtain walling, the Secretariat of

28、 which is held by AFNOR.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2003, and conflicting national standards shall be withdrawn at the latest by September 2004.This document has been prep

29、ared under a mandate given to CEN by the European Commission and The European Free Trade Association, and supports For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.NOTE This amendment refers only to requirements under the Construction Produc

30、ts Directive (89/106/EEC), and CE marking is considered only in regard to this Directive. Where full CE marking may require compliance with other directives it is understood that this is done by following the relevant risk assessment(s) of these other directives, performed in addition to the require

31、ments of this standard.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, M

32、alta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.ContentsPageForeword 21Scope 32 Normative references 33 Definitions 34 Classification 45 Requirements 56 Test apparatus 77 Test methods 88 Marking 129 Evaluation of conformity 12Annex A (informative) Overload perf

33、ormance test apparatus 14Annex B (normative) Flow chart of test procedures 16Annex C (informative) Bibliography 17Annex ZA (informative) Clauses addressing the provisions of the EU Construction Products Directive (89/106/EEC) 18Figure A.1 Typical general arrangement 14Figure A.2 Arrangement for open

34、ing overload test 15Table 1 52essential requirements of EU Directive(s). BSI 2006EN 1155:19971 ScopeThis European Standard specifies requirements for separate hold-open devices and also for hold-open mechanisms incorporated in a door closer !intended to be used on fire/smoke compartmentation doors“.

35、 Electrically powered hold-open devices for swing doors manufactured according to this European Standard can hold a swing door at a fixed position or can allow the door to swing freely. In each case interruption of the electrical supply will cause the controlled door to close positively.Electrically

36、 powered hold-open devices manufactured in accordance with this European Standard are recommended for use wherever there is a requirement for reliable hold-open and release of self-closing fire/smoke door assemblies.Whilst these devices can incorporate smoke or fire detection elements, the performan

37、ce of those particular elements is outside the scope of this European Standard.!Door closing devices are covered by EN 1154.“NOTE The series of European Standards EN 54 covers the requirements, test methods and performance criteria of resettable smoke/fire detectors.2 Normative referencesThis Europe

38、an Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications a

39、pply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies.EN 1154, Building hardware Controlled door closing devices Requirements and test methods.!EN 1634-1“, Fire resistance tests for door

40、and shutter assemblies Part 1: Method of test for fire resistance of fire doors and shutters.!EN 1634-3, Fire resistance tests for door and shutter assemblies Part 3: Smoke control doors and shutters.“!EN 1670“, Building hardware Corrosion resistance of hardware for doors, windows, shutters and curt

41、ain walling Requirements and test methods.3 Definitions!For the purposes of this European Standard, the terms and definitions listed in EN 1154 apply together with the following:“3.1 electrically powered hold-open device3.1.1 electrically powered separate hold-open devicedevice that allows a door, f

42、itted with a separate door closer, to remain open at either a preset or chosen angle until electrically released3.1.2 electrically powered hold-open door closerdoor closer that incorporates an electrically powered hold-open3.1.3 electrically powered free-swing door closerdoor closer that allows a do

43、or, after an initial opening to a predetermined position, to swing freely anywhere from that position to its closed position without any resistance or damping. Upon removal of the electrical supply, the door returns to the closed position under the control of the door closer!Text deleted“3 BSI 2006E

44、N 1155:1997!3.2“hold-open power sizemeasure of the holding force exerted by the hold-open device, related to the power size of the door closing devices fitted!3.3“manual releaseaction of pulling a door held open by a device to this European Standard, from its held position without removing the elect

45、rical supply, such that it will continue to the closed position under the control of the door closer!3.4“release momentmoment required to manually release a door from its held position!3.5“rated supply voltagenominal voltage for which the device is intended!Text deleted“4 Classification4.1 !Coding s

46、ystem“For the purpose of this European Standard, electrically powered hold-open devices shall be classified according to the following six digit coding system:4.2 Category of use (first digit)Only one category of use is identified for electrically powered hold-open devices: grade 3: For doors for us

47、e by the public, and others, with little incentive to take care, i.e. where there is some chance of misuse of the door.NOTE For electrically powered hold-open and free-swing door closers, where the opening angle is limited by the device, provision of a separate door stop should be considered.4.3 !Du

48、rability“ (second digit)Two test durations are identified for devices manufactured to this European Standard: grade 5: 50 000 test cycles. For all electrically powered hold-open devices (see 5.2.4); grade 8: 500 000 test cycles. For all electrically powered hold-open and free-swing door closers and

49、devices that contain operating arms (see 7.2.8.3).4.4 !Hold-open power size“ (third digit)!Five hold-open power sizes are identified according to Table 1 of this European Standard.“Where an electrically powered hold-open device is suitable for a range of door closer power sizes, both the minimum and maximum power sizes shall be identified.!Text deleted“4.5 !Suitability for use on fire/smoke compartmentation doors“ (fourth digit)Only one grade of !suitability for use on f