BS DD ISO TS 16952-10-2009 Technical product documentation - Reference designation system - Power plants《技术产品文件 参考标识系统 发电厂》.pdf

《BS DD ISO TS 16952-10-2009 Technical product documentation - Reference designation system - Power plants《技术产品文件 参考标识系统 发电厂》.pdf》由会员分享，可在线阅读，更多相关《BS DD ISO TS 16952-10-2009 Technical product documentation - Reference designation system - Power plants《技术产品文件 参考标识系统 发电厂》.pdf（56页珍藏版）》请在麦多课文档分享上搜索。

1、DD ISO/TS16952-10:2008ICS 01.110NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWDRAFT FOR DEVELOPMENTTechnical productdocumentation Reference designationsystemPart 10: Power plantsThis Draft for Developmentwas published under theauthority of the StandardsPolicy and StrategyComm

2、ittee on 30 April2009 BSI 2009ISBN 978 0 580 64741 3Amendments/corrigenda issued since publicationDate CommentsDD ISO/TS 16952-10:2008National forewordThis Draft for Development is the UK implementation of ISO/TS16952-10:2008.This publication is not to be regarded as a British Standard.It is being i

3、ssued in the Draft for Development series of publications andis of a provisional nature. It should be applied on this provisional basis,so that information and experience of its practical application can beobtained.Comments arising from the use of this Draft for Development arerequested so that UK e

4、xperience can be reported to the internationalorganization responsible for its conversion to an international standard.A review of this publication will be initiated not later than 3 years afterits publication by the international organization so that a decision can betaken on its status. Notificati

5、on of the start of the review period will bemade in an announcement in the appropriate issue of Update Standards.According to the replies received by the end of the review period,the responsible BSI Committee will decide whether to support theconversion into an international Standard, to extend the

6、life of theTechnical Specification or to withdraw it. Comments should be sent tothe Secretary of the responsible BSI Technical Committee at BritishStandards House, 389 Chiswick High Road, London W4 4AL.The UK participation in its preparation was entrusted to TechnicalCommittee TDW/4, Technical produ

7、ct realization (TPR).A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot co

8、nfer immunityfrom legal obligations.DD ISO/TS 16952-10:2008Reference numberISO/TS 16952-10:2008(E)ISO 2008TECHNICAL SPECIFICATION ISO/TS16952-10First edition2008-11-15Technical product documentation Reference designation system Part 10: Power plants Documentation technique de produits Systme de dsig

9、nation de rfrence Partie 10: Centrales lectriques DD ISO/TS 16952-10:2008ISO/TS 16952-10:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded

10、 are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Det

11、ails of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem

12、relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including

13、 photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published i

14、n Switzerland ii ISO 2008 All rights reservedDD ISO/TS 16952-10:2008ISO/TS 16952-10:2008(E) ISO 2008 All rights reserved iiiContents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references . 1 3 Terms and definitions. 2 4 Designation systematic 5 4.1 General. 5 4.2 Process of forming desi

15、gnations 5 4.3 General rules for designation structure . 6 4.4 Rules for forming designations. 7 5 Designation tasks . 8 5.1 General. 8 5.2 Conjoint designation (optional). 9 5.3 Designation of technical objects Reference designation 9 5.4 Specific designations. 12 6 Structure and contents of design

16、ation blocks 12 6.1 General. 12 6.2 Designation block “Conjoint designation” 12 6.3 Function aspect 13 6.4 Product aspect 15 6.5 Transition from function aspect to product aspect 15 6.6 Location aspect. 19 6.7 Specific designations. 22 7 Application of designation. 26 7.1 Combination of designation

17、blocks 26 7.2 Designation notation 27 Annex A (normative) Representation of designations . 29 Annex B (normative) Special stipulations . 31 Annex C (informative) Stipulations between parties to the project 35 Annex D (informative) Application examples 36 Bibliography . 44 DD ISO/TS 16952-10:2008ISO/

18、TS 16952-10:2008(E) iv ISO 2008 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Eac

19、h member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Internation

20、al Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standard

21、s adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. In other circumstances, particularly when there is an urgent market requirement for such documents, a

22、 technical committee may decide to publish other types of document: an ISO Publicly Available Specification (ISO/PAS) represents an agreement between technical experts in an ISO working group and is accepted for publication if it is approved by more than 50 % of the members of the parent committee c

23、asting a vote; an ISO Technical Specification (ISO/TS) represents an agreement between the members of a technical committee and is accepted for publication if it is approved by 2/3 of the members of the committee casting a vote. An ISO/PAS or ISO/TS is reviewed after three years in order to decide w

24、hether it will be confirmed for a further three years, revised to become an International Standard, or withdrawn. If the ISO/PAS or ISO/TS is confirmed, it is reviewed again after a further three years, at which time it must either be transformed into an International Standard or be withdrawn. Atten

25、tion is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO/TS 16952-10 was prepared by Technical Committee ISO/TC 10, Technical product documentation, Subcommitt

26、ee SC 10, Process plant documentation and tpd-symbols. ISO 16952 consists of the following parts, under the general title Technical product documentation Reference designation system: Part 1: General application rules Technical Specification Part 10: Power plants Technical Specification Further part

27、s on sector-specific rules are under consideration. DD ISO/TS 16952-10:2008ISO/TS 16952-10:2008(E) ISO 2008 All rights reserved vIntroduction Based on ISO/TS 16952-1, this part of ISO 16952 serves to designate plants, sections of plants and items of equipment in any type of installation for industri

28、al production of electrical and thermal energy according to task, type and location. This sector-specific Reference Designation System (RDS) is intended for application by all engineering disciplines for the entire life cycle of a plant, from planning, licensing, construction, operation and maintena

29、nce, re-powering, extension and recreation, to dismantling and demolition. Based on the structuring principles and reference designation rules of IEC 61346 and other documents, ISO 16952 breaks down these rules into interdisciplinary guidelines for practical application. The relationships of input d

30、ocuments with this part of ISO 16952 are shown in Figure 1. Figure 1 Structuring and designation standards This part of ISO 16952 establishes the prerequisites for uniform designation of all power plant processes (see Figure 2 for a summary of the energy conversion cycle), uniform designation of all

31、 power plant types, language-independent codes to ensure international applicability, adequate capacity and possible detail for designation of all systems, equipment and structures, adequate extension possibilities for new technologies, consistent designation for planning, licensing, construction, o

32、peration, maintenance and decommissioning, common applicability in mechanical, electrical, instrumentation and control (I how the system or object is constructed (product viewpoint); where the system or object is located (location viewpoint). IEC 61346-1 3.3 auxiliary system system which is required

33、 for the support of a power plant process NOTE This includes auxiliary steam system, compressed air, carrier air, control air, central chemicals supply, sampling systems, etc. 3.4 control purposeful action on or in a process to meet specified objectives IEC 60050-351 NOTE This includes measure, coun

34、t, monitor, indicate, alert, record, log, manipulate, evaluate, optimize, intervene, manipulate by hand, safeguard, structure, configure, parameter, automate. 3.5 designation block structured compilation of related information units, consisting of a prefix, letters and numbers, and optionally a brea

35、kdown mark 1) Source: www.vgb.org DD ISO/TS 16952-10:2008ISO/TS 16952-10:2008(E) ISO 2008 All rights reserved 33.6 document kind class group of document kinds having similar characteristics concerning the content of information independent of the form of presentation IEC 61355 3.7 documentation coll

36、ection of documents related to a given subject NOTE This may include technical, commercial and/or other documents. IEC 61082-1 3.8 functional area combination of groups and/or elements in a unit that can be used independently 3.9 functional group combination of elements in a unit that can be used in

37、dependently 3.10 functional unit item under consideration defined according to function or effect NOTE 1 A functional unit produces the interactive effect between input variables and output variables. NOTE 2 A functional unit may be implemented by one or several physical units or program modules. NO

38、TE 3 If compound terms are used to designate functional units, the following should be used as the last word (in ascending order of rank): element; equipment; system. For the subject under consideration, it is understood that “element” should designate the smallest functional unit in each case. IEC

39、60050-351 3.11 multi-level reference designation reference designation derived from a structural path through an overall system IEC 61346-1 3.12 object entity treated in the process of design, engineering, realization, operation, maintenance and demolition NOTE 1 The entity may refer to a physical o

40、r non-physical “thing”, or to a set of information associated with it. NOTE 2 Depending on its purpose, an object may be viewed in different ways called “aspects”. IEC 61346-1 DD ISO/TS 16952-10:2008ISO/TS 16952-10:2008(E) 4 ISO 2008 All rights reserved3.13 operating equipment all products, which se

41、rve to implement technical tasks as a whole or in individual parts 3.14 physical unit item under consideration, defined according to construction or configuration NOTE 1 One or several functional units may be implemented in a single physical unit. The corresponding functional unit(s) is/are in some

42、cases not explicitly designated. NOTE 2 The various parts of a physical unit need not be functionally interrelated. For example, a physical unit may be in the form of an integrated circuit with four independent AND modules. NOTE 3 If compound terms are used to designate physical units, the following

43、 should be used as the last word (in ascending order of rank): component; assembly; device; plant. For the subject under consideration it is understood that “component” should designate the smallest physical unit in each case. NOTE 4 The designations of conceptually corresponding functional units an

44、d physical units are stated together in the following if they are commonly used but different from each other. IEC 60050-351 3.15 plant complete set of technical equipment and facilities for solving a defined technical task NOTE A plant includes apparatus, machines, instruments, devices, means of tr

45、ansportation, control equipment and other operating equipment. IEC 60050-351 3.16 plant section part of a process plant that can, at least occasionally, be operated independently ISO 10628 3.17 power plant process process for the generation of electrical energy and/or heat energy products, including

46、 the conversion, supply, and disposal processes 3.18 power plant unit technical plant including all equipment needed for fulfilment of a power plant process DD ISO/TS 16952-10:2008ISO/TS 16952-10:2008(E) ISO 2008 All rights reserved 53.19 system set of interrelated objects NOTE 1 Examples of a syste

47、m: a drive system, a water supply system, a stereo system, a computer. NOTE 2 When a system is part of another system, it may be considered as an object. IEC 61346-1 3.20 technical equipment physical or functional unit used to fulfil a technical task 3.21 terminal point of access to an object intend

48、ed for connection to an external network NOTE 1 The connection may refer to a) a physical interface between conductors and/or contacts, or piping and/or duct systems to provide a signal, energy or material flow path, b) an association of functional nature established between logical elements, softwa

49、re modules, etc. for conveying information. NOTE 2 The external networks may be of different nature and accordingly they may be classified. IEC 81714-3 provides such classifications. IEC 61666 3.22 works system of industrial complexes and the associated infrastructure in one location ISO 10628 4 Designation systematic 4.1 General The designation systematic has to be understood as a well-organized, methodical process of forming permanent designations with ergonomic no